Enhanced Oxygen Isotope Determination in Uranium Oxides Using BrF5 Fluorination

A new method for accurate determination of oxygen isotopes in uranium oxides encountered in the nuclear fuel cycle was developed using the conventional BrF₅ fluorination technique. Laser‐assisted fluorination was tested for comparison. We focused on fine powders of triuranium octoxide (U₃O₈), uranium dioxide (UO_2±x with 0 ≤ x ≤ 0.25), uranium trioxide (UO₃.nH₂O, with 0.8 ≤ n ≤ 2) and diuranates (M₂U₂O₇.nH₂O, with M = NH₄, Na or Mg_0.5 and 0 ≤ n ≤ 6). Fluorination at room temperature and heating under vacuum at 150 °C are shown to eliminate both adsorbed and structural water from the powder samples. Precision fit for purpose of δ¹⁸O values (± 0.3‰, 1s) and oxygen yields (close to 100%) were obtained for U₃O₈ and UO₂ where oxygen is only bound to uranium. A lower precision was observed for UO₃.nH₂O and M₂U₂O₇.nH₂O where oxygen is both present in the structural H₂O and bonded to uranium and where the extracted O_2(g) can be contaminated by NF₃ and NO_x compounds. Laser‐assisted fluorination gave shifted δ¹⁸O values between +0.8 and +1.4‰ for U₃O₈, around ?0.8‰ for UO₃.nH₂O and between ?3.9 and ?4.5‰ for M₂U₂O₇.nH₂O (± 0.3‰, 1s) compared with the conventional method.     

Thermal Impact on Damaged Boom Clay and Opalinus Clay: Permeameter and Isostatic Tests with μCT Scanning

Within the framework of the TIMODAZ project, permeameter tests and isostatic tests were performed on Boom Clay and Opalinus Clay in order to assess the impact of temperature, pore water composition, and confining stress on the sealing of damaged samples of Boom Clay and Opalinus Clay. A microfocus X-ray computed tomography technique was used to visualize the evolution of the sealing process. Compared to the fast sealing of Boom Clay, the sealing of Opalinus Clay was much slower. The heating showed a significant, favorable impact on the sealing behavior of Opalinus Clay under permeameter test conditions, while the sealing behavior of Boom Clay appeared to be unaffected. Tests performed under isostatic conditions did not reveal a significant influence of a heating–cooling cycle on the sealing behavior of these clays. The reappearance of the fractures or holes in the samples after dismantling confirms earlier observations which showed that after sealing, the original mechanical properties are not recovered. In other words, a heating cycle does not seem to induce healing.     

3D quantification of mineral components and porosity distribution in Westphalian C sandstone by microfocus X-ray computed tomography

Microfocus X-ray computed tomography (µCT) measurements were performed on deltaic sandstone samples from the diagenetically altered Westphalian C strata (Campine basin, north-east Belgium) in order to collect three dimensional data on mineral (quartz, kaolinite, ankerite, etc.) and porosity distribution. The acquired µCT data were compared with point counting results of stained impregnated thin-sections to qualify the sensitivity of µCT. Comparison between techniques shows positive results with regard to the quantification of main mineral phases such as quartz and ankerite, and porosity distribution. However, major discrepancies exist when studying the clay minerals. This can be explained by the influence of microporosity associated with these clay minerals, resulting in partial volume effects.     

The use of neutrons and monochromatic X-rays for non-destructive testing in geological materials

In the paper we present our results for element sensitive high-energy X-ray tomography and high-speed thermal neutron tomography applied to geological samples. The tuneable monochromatic X-ray beam was used for element sensitive tomography of geological samples containing heavy elements using the K-edge dichromatic scanning technique. This type of NDT (non-destructive testing) allowed us to reveal the quantity and location of uranium, lead and mercury in Oklo samples (natural nuclear reactor) and Cinnabar stones. Fast 3-D thermal neutron imaging of dynamical processes was successfully tested at the high flux neutron tomography station of the ILL. The qualitative investigation of water repellents and consolidants applied on sandstones of Bray and limestones of Maastricht were the first samples to be studied with the new imaging technique.