A laboratory experiment to monitor the contact state of a fault by transmission waves

We performed a series of laboratory experiments in which elastic waves were transmitted across a simulated fault. Two types of experiments were carried out: (1) Normal Stress Holding Test (NSHT): normal stress was kept constant for about 3 h without shear stress and transmission waves were observed. (2) Shear Stress Increasing Test (SSIT): shear stress was gradually increased until a stick-slip event occurred. Transmission waves were continuously observed throughout the process of stress accumulation. We focused on the change in transmission waves during the application of shear stress and especially during precursory slips.It was found in NSHT that the amplitude of transmission waves linearly increased with the logarithm of stationary contact time. The increase amounted to a few percent after about 3 h. Creep at asperity contacts is responsible for this phenomenon. From a theoretical consideration, it was concluded that the real contact area increased with the logarithm of stationary contact time.We observed in SSIT a significant increase in wave amplitude with shear stress application. This phenomenon cannot be attributed to the time effect observed in NSHT. Instead, it can be explained by the mechanism of “junction growth” proposed by Tabor. Junction growth yields an increase in real contact area. It is required for junction growth to occur that the material in contact is already plastic under a purely normal loading condition. A computer simulation confirmed that this requirement was satisfied in our experiments. We also found that the rate at which the amplitude increased was slightly reduced prior to a stick-slip event. The onset time of the reduction well coincides with the onset of precursory slip. The cause of the reduction is attributed to the reset of stationary contact time due to displacement. This interpretation is supported by the result of NSHT. Taking the time of stationary contact in SSIT into account, we may expect the change in wave amplitude to be, at most, only a few percent. The observed slight reduction in increasing rate is, in this sense, reasonable. The static stiffness of the fault also decreases with precursory slip. It was also found that low frequency waves are a better indicator of precursory slip than high frequency waves. This might suggest that low frequency waves with longer wavelength are a better indicator of average behavior of faults. The problem, however, merits a further investigation. The shifts in phase were also found to be a good indicator of the change in contact state of the fault. The changes in both amplitude and phase of transmission waves are unifyingly understood through the theory of transmission coefficient presented by Pyrak-Nolte et al. Rough surfaces have a tendency to give larger stick-slips than smooth surfaces. The amount of precursory slip is larger for rough surfaces than for smooth surfaces. Although it was confirmed by a computer simulation that rough surfaces have larger contact diameters than smooth surfaces, the rigorous relationship between the surface roughness (contact diameter) and the amount of precursory slips was not established.     

The characteristic displacement in rate and state-dependent friction from a micromechanical point of view

The physical meaning of the characteristic displacement that has been observed in velocity-stepping friction experiments was investigated based on the micromechanics of asperity contact. It has been empirically found for bare rock surfaces that the magnitude of the characteristic displacement is dependent only on surface roughness and insensitive to both slip velocity and normal stress. Thus the characteristic displacement has been interpreted as the displacement required to change the population of contact points completely. Here arises a question about the physical mechanism by which the contact population changes. Because individual asperity contacts form, grow and are eliminated with displacement, there are at least two possible interpretations for the characteristic displacement: (1) it is the distance over which the contacts existing at the moment of the velocity change all fade away, being replaced by new asperity contacts, or (2) it is the distance required for a complete replacement in the real contact area that existed at the moment of the velocity change. In order to test these possibilities, theoretical models were developed based on the statistics of distributed asperity summits. A computer simulation was also performed to check the validity of the theoretical models using three-dimensional surface topography data with various surface roughnesses. The deformation was assumed to be elastic at each asperity contact. The results of both the simulation and the theoretical models show that the characteristic displacement in (1) is about three times longer than that in (2). Comparison of the results with the experimental observations obtained by others indicates that the possibility (2) is the correct interpretation. This means that the state in the rate and state variable friction law is memorized in a very confined area of real contact. Further, our results explain why the characteristic displacement is insensitive to normal stress: this comes from the fact that the microscopic properties such as the mean contact diameter are insensitive to normal stress. The approach based on the micromechanics of asperity contact is useful to investigate the underlying mechanism of various phenomena in rock friction.     

Crystal chemistry and oxidation state of Fe-rich prehnite from a hydrothermally altered dolerite

Mineralogy and Petrology - Fe-rich prehnite, Ca2(Al,Fe)(AlSi3)O10(OH)2, in a hydrothermally altered dolerite sill from Mitsu, Shimane Peninsula, Japan, was studied using 57Fe Mössbauer...     

International Pellet Watch: Global monitoring of persistent organic pollutants (POPs) in coastal waters. 1. Initial phase data on PCBs, DDTs, and HCHs

Samples of polyethylene pellets were collected at 30 beaches from 17 countries and analyzed for organochlorine compounds. PCB concentrations in the pellets were highest on US coasts, followed by western Europe and Japan, and were lower in tropical Asia, southern Africa and Australia. This spatial pattern reflected regional differences in the usage of PCBs and was positively correlated with data from Mussel Watch, another monitoring approach. DDTs showed high concentrations on the US west coast and in Vietnam. In Vietnam, DDT was predominant over its metabolites (DDE and DDD), suggesting the principal source may be current usage of the pesticide for malaria control. High concentrations of pesticide HCHs were detected in the pellets from southern Africa, suggesting current usage of the pesticides in southern Africa. This study demonstrates the utility and feasibility of the International Pellet Watch approach to monitor POPs at a global scale.