Stochastic modelling of groundwater flow and solute transport in aquifers

This paper presents an introductory overview of recently developed stochastic theories for tackling spatial variability problems in predicting groundwater flow and solute transport. Advantages and limitations of the theories are discussed. Lastly, strategies based on the stochastic approaches to predict solute transport in aquifers are recommended.     

Effect of spatial variation characteristics on contouring of design storm depth

The ordinary kriging method, a geostatistical interpolation technique, was applied for developing contour maps of design storm depth in northern Taiwan using intensity–duration–frequency (IDF) data. Results of variogram modelling on design storm depths indicate that the design storms can be categorized into two distinct storm types: (i) storms of short duration and high spatial variation and (ii) storms of long duration and less spatial variation. For storms of the first category, the influence range of rainfall depth decreases when the recurrence interval increases, owing to the increasing degree of their spatial independence. However, for storms of the second category, the influence range of rainfall depth does not change significantly and has an average of approximately 72 km. For very extreme events, such as events of short duration and long recurrence interval, we do not recommend usage of the established design storm contours, because most of the interstation distances exceed the influence ranges. Our study concludes that the influence range of the design storm depth is dependent on the design duration and recurrence interval and is a key factor in developing design storm contours. Copyright © 2003 John Wiley & Sons, Ltd.     

CO<Subscript>2</Subscript> Flux Measurements over the Sea Surface by Eddy Correlation and Aerodynamic Techniques

The measurements of the vertical transport of CO₂ were carried out over the Sea of Japan using the specially designed pier of Kyoto University on September 20 to 22, 2000. CO₂ fluxes were measured by the eddy correlation and aerodynamic techniques. Both techniques showed comparable CO₂ fluxes during sea breeze conditions: −0.001 to −0.08 mg m⁻²s⁻¹ with the mean of −0.05 mg m⁻²s⁻¹. This means that the measuring site satisfies the fetch requirement for meteorological observations under sea breeze conditions. Moreover, the eddy diffusivity coefficient used in the aerodynamic technique is found to be consistent with the coefficient used in the eddy correlation technique. The present result leads us to conclude that the aerodynamic technique may be applicable to underway CO₂ flux measurements over the ocean and may be used in place of the bulk technique. The important point is the need to maintain a measuring accuracy of CO₂ concentration difference of the order of 0.1 ppmv on the research vessels or the buoys.     

Scaling analysis of deposition from turbidity currents

Many oil-bearing sedimentary deposits are formed by the settling of particles from turbidity currents. Modeling sedimentary processes that form these turbidites enables the calculation of properties such as extent, depth, porosity and permeability of hydrocarbon-bearing reservoirs. This paper estimates the extent and thickness of turbidites from the initial conditions of the turbidity flow. This is achieved by the application of scaling analysis of the partial differential equations that govern the dynamics of and deposition from turbidity currents. We apply the results of scaling analysis to five modern submarine fans. The predicted and actual values of the dimensions of the fan deposits match well. We then compare the derived results against tabulated sizes of ancient turbidites. The comparisons are good as long as we correctly identify the flow regimes in which the deposition took place. The good agreements observed in the two cases show that the estimates obtained using scaling analysis can provide useful first-guess values for the dimensions of the deposits.     

Simple determination of dimethylsulfide (DMS) and dimethylsulfoniopropionate (DMSP) using solid-phase microextraction and gas chromatography-mass spectrometry

Solid-phase microextraction (SPME) is a simple, sensitive and less destructive method for the determination of dimethylsulfide (DMS) in seawater. Combined with detection by gas chromatography-mass spectrometry (GC-MS), the method had sufficient sensitivity (minimum detectable concentration of DMS was 0.05 nM), and practical levels of reproducibility (relative standard deviation ≤7%) and linearity (r ² > 0.995) over a wide concentration range (0.5 to 910 nM). The protocol developed was applied to a Sagami Bay water sample to determine concentrations of DMS and DMSP, and in situ DMSP-lyase activity.     

Pumpellyite in Low-grade Metamorphism

The regional metamorphism of the Kant? Mountains in Japan producedrocks of the following facies, with rising temperature: chloritefacies, pumpellyite-chlorite facies, glauco-phane-schist facies,and greenschist facies. This relationship is compared with theprogressive metamorphic zones in other regions where pumpellyitehas been found. Almost similar relations appear to hold in manymetamorphic terrains. Pumpellyites in glaucophanitic metamorphicterrains have, generally, low Fe'/R'R ratios. Physical andchemical conditions responsible for the formation of pumpellyiteare also discussed.     

Fluid inclusion studies of the Abawso gold prospect,near the Ashanti Belt,Ghana

The major Ghanaian lode gold deposits are preferentially aligned along the western and eastern contacts of the Kumasi Basin with the Ashanti and Sefwi Belts, respectively. The investigated area of the Abawso small-scale concession, covering the workings of the old Ettadom mine, is situated 3 km west of the lithological contact of the Birimian metavolcanic rocks of the Akropong Belt in the east with the Birimian metasedimentary rocks of the Kumasi Basin in the west. The rocks of the Abawso concession represent a steeply NW-dipping limb of a SE-verging anticline with an axis plunging to the SW. Quartz veining occurs predominantly in the form of en échelon dilatational veins along NNE–SSW-striking shear zones of a few metres width and shows evidence of brittle and ductile deformation. Also stockwork-style quartz veining occurs in the vicinity of the main shaft of the old Ettadom mine. Hydrothermal alteration includes sericitisation, sulphidation and locally carbonatisation. The auriferous quartz veins mainly follow the trend of brittle to ductile deformed quartz veins; however, some occur in stockwork. Fluid inclusion studies reveal a large number of H₂O inclusions along intragranular trails in auriferous quartz vein samples, as well as an overall dominance of H₂O and H₂O-CO₂ inclusions over CO₂ inclusions. Textural observations and physico-chemical fluid inclusion properties indicate post-entrapment modifications for all quartz vein samples due to grain boundary migration recrystallisation. This process is interpreted to be responsible for the generation of the CO₂ inclusions from a H₂O-CO₂ parent fluid. In comparison with mineralisation at the Ashanti and Prestea deposits, which are characterised by CO₂±N₂ inclusions, the observed inclusion assemblage may be due to a shallower crustal level of mineralisation, or different degrees and styles of recrystallisation, or a less pronounced development of laminated quartz veins due to comparably restricted pressure fluctuations. Furthermore, the microthermometric observations allow the reconstruction of a possible retrograde P-T path, depicting near-isothermal decompression in the P-T range of the brittle/ductile transition.Editorial handling: E. Frimmel