A Shear Model Accounting Scale Effect in Rock Joints Behavior

Understanding the scale effect on the mechanical behavior of a single rock joint is still very important in rock engineering. Rock joints can be classified into three different categories depending on their scale: the “micro scale” which is the scale of the asperities; the “meso scale” is the scale of the specimens tested in laboratory; and the “macro scale” which is the scale of the rock mass. The purpose of this paper is to propose an effective way to model rock joints at both the meso and macro scale. An original constitutive mechanical model, in which parameters are deduced from experimental results, has been developed. This model is then extended to simulate the discontinuities occurring at a larger size. At the macro scale, the constitutive modeling was carried out for both small and large relative displacements. Large displacements lead to substantial changes in dilation. For both cases, the peak shear stress vanishes for joints longer than 2 m.     

A viscoplastic model including anisotropic damage for the time dependent behaviour of rock

This paper presents a new constitutive model for the time dependent mechanical behaviour of rock which takes into account both viscoplastic behaviour and evolution of damage with respect to time. This model is built by associating a viscoplastic constitutive law to the damage theory. The main characteristics of this model are the account of a viscoplastic volumetric strain (i.e. contractancy and dilatancy) as well as the anisotropy of damage. The latter is described by a second rank tensor. Using this model, it is possible to predict delayed rupture by determining time to failure, in creep tests for example. The identification of the model parameters is based on experiments such as creep tests, relaxation tests and quasi‐static tests. The physical meaning of these parameters is discussed and comparisons with lab tests are presented. The ability of the model to reproduce the delayed failure observed in tertiary creep is demonstrated as well as the sensitivity of the mechanical response to the rate of loading. The model could be used to simulate the evolution of the excavated damage zone around underground openings. Copyright © 2005 John Wiley & Sons, Ltd.     

Experimental Study of Mechanical Behaviour of Rock Joints Under Cyclic Loading

Summary Evaluation of the effects of small repetitive earthquakes on the strength parameters of rock joints in active seismic zones is of interest of the designers of underground constructions. In order to evaluate these effects, it is necessary to study the behaviour of rock joints under dynamic and cyclic loadings. This paper presents the results of a systematic study on the behaviour of artificial rock joints subjected to cyclic shearing. More than 30 identical replicas have been tested using triaxial compression devices under different conditions of monotonic and cyclic loading. At the first stage a few samples have been tested in monotonic loading modes under various confining pressures and rate of displacement. In the second series of tests, small cyclic loads were applied on the samples for increasing number of cycles, frequency levels and stress amplitudes. These were then followed by monotonic loading again. The variations of maximum and residual shear strengths for each test have been studied. The results show increase of shear strength as a result of the increase in confining pressure and they display decrease of shear strength due to the increase of rate of loading, number of cycles, frequency levels and stress amplitudes.     

Evaluation of shear strength of rock joints subjected to cyclic loading

Variation of the shear strength of rock joints due to cyclic loadings is studied in the present paper. Identical joint surfaces were prepared using a developed moulding method with special mortar and shear tests were performed on these samples under both static and cyclic loading conditions. Different levels of shear displacement were applied on the samples to study joint behaviour before and during considerable relative shear displacement. It was found that the shear strength of joints is related to rate of displacement (shearing velocity), number of loading cycles and stress amplitude. Finally, based on the experimental results, mathematical models were developed for evaluation of shear strength in cyclic loading conditions.     

Analytical model for the mechanical behaviour of bolted rock joints subjected to shearing

Summary This study proposes a new analytical model for the prediction of the contribution of bolts to the shear strength of a rock joint. The main characteristics of this model are the accounts for the interaction of the axial and the shear forces mobilised in the bolt, as well as the large plastic displacements of the bolt occurring during the loading process. The complete curve of the bolt contribution as a function of the displacement along the joint can be computed, and the maximum bolt contribution is obtained by dissociating the bolt cohesion and the confinement effects. The comparison of the performances of this analytical model with test results shows its capacity to describe the observed phenomena. The effects of the most important parameters such as bolt inclination, mechanical properties of bolt material, rock strength and joint friction angle are clearly established and discussed.     

Damage and Changes in Mechanical Properties of a Gabbro Thermally Loaded up to 1,000°C

Thermal loading of rocks at high temperatures induces changes in their mechanical properties. In this study, a hard gabbro was tested in the laboratory. Specimens were slowly heated to a maximum temperature of 1,000°C. Subsequent to the thermal loading, specimens were subjected to uniaxial compression. A drastic decrease of both unconfined compressive strength and elastic moduli was observed. The thermal damage of the rock was also highlighted by measuring elastic wave velocities and by monitoring acoustic emissions during testing. The micromechanisms of rock degradation were investigated by analysis of thin sections after each stage of thermal loading. It was found that there is a critical temperature above which drastic changes in mechanical properties occur. Indeed, below a temperature of 600°C, microcracks start developing due to a difference in the thermal expansion coefficients of the crystals. At higher temperatures (above 600°C), oxidation of Fe²⁺ and Mg²⁺, as well as bursting of fluid inclusions, are the principal causes of damage. Such mechanical degradation may have dramatic consequences for many geoengineering structures.     

Thermal structure and metamorphic evolution of the Piemont-Ligurian metasediments in the northern Western Alps

In the Western Alps, the Piemont-Ligurian oceanic domain records blueschist to eclogite metamorphic conditions during the Alpine orogeny. This domain is classically divided into two “zones” (Combin and Zermatt-Saas), with contrasting metamorphic evolution, and separated tectonically by the Combin fault. This study presents new metamorphic and temperature (RSCM thermometry) data obtained in Piemont-Ligurian metasediments and proposes a reevaluation of the P–T evolution of this domain. In the upper unit (or “Combin zone”) temperatures are in the range of 420–530 °C, with an increase of temperature from upper to lower structural levels. Petrological evidences show that these temperatures are related to the retrograde path and to deformation at greenschist metamorphic conditions. This highlights heating during exhumation of HP metamorphic rocks. In the lower unit (or “Zermatt-Saas zone”), temperatures are very homogeneous in the range of 500–540 °C. This shows almost continuous downward temperature increase in the Piemont-Ligurian domain. The observed thermal structure is interpreted as the result of the upper and lower unit juxtaposition along shear zones at a temperature of ~500 °C during the Middle Eocene. This juxtaposition probably occurred at shallow crustal levels (~15–20 km) within a subduction channel. We finally propose that the Piemont-Ligurian Domain should not be viewed as two distinct “zones”, but rather as a stack of several tectonic slices.     

Numerical evidence of site effects contributing to triggering the Las Colinas landslide during the 2001 <Emphasis Type="Italic">M</Emphasis><Subscript>w</Subscript> = 7.7 El Salvador earthquake

The Las Colinas landslide, which was triggered by the 13 January 2001, M_w?=?7.7 El Salvador earthquake, was highly destructive. The local site is composed of pyroclastic flows, brown cinders, soft pyroclastic fall deposits and a thin palaeosol and is characterised by steep slopes. The extremely high ground motions recorded near the landslide location are assumed to be both produced by site effects and responsible for the landslide. To characterise the ground motion amplifications due to site effects in terms of the variation in geometrical and geological settings, parametric studies were conducted with a linear elastic slope model, which was vertically subjected to the scattering SV wave of the Gabor wavelet. The results show that a maximum amplification is obtained when the model slope angle is approximately 30° (similar to the actual slope angle), and the maximum amplification is located approximately 20 m behind the crest, where the actual movement was initiated. Additionally, a slope with a height of approximately 160 m enhances ground motion amplification. The subsurface geology is found to induce a greater effect on amplification than that of the slope topography. In particular, a soft pyroclastic fall deposit is observed to contribute most of the ground motion amplification. According to the numerical results, it can be concluded that the local site conditions induced extremely high ground motions that then contributed to the slope movement. Although the thin, buried layer of palaeosol did not cause any significant amplification, its weak cohesion enhanced movement.