Assessment of seismic hazard for the Sannio-Matese area of Southern Italy — A summary

The working group on Test Regions for Evaluation of Methods for Seismic Hazard Assessment in Europe (TERESA), consisted of 15 members from 10 different European countries. Methods and experience gathered in these countries have been compared and discussed for two test areas in Europe: the Sannio-Matese region, Southern Italy, with high seismic activity, and the border region between Belgium, The Netherlands, and Federal Republic of Germany, with low activity.This paper summarizes the results for one of the test areas, Sannio-Matese. Most of the participants used statistical procedures to assess earthquake hazard, receiving results in terms of probability of occurrence for intensity as the ground-motion parameter. It was found that careful preparation of input data and parameters is the major influencing factor, therefore most of the efforts of the working group was devoted to this task.The scatter of the obtained results of the group is considerable, mainly because of the uncertainties in the data and the subjectiveness involved in the procedures. For better control of both factors, more objective methods have to be developed.     

Seismic hazard computations for regions with low earthquake activity — A case study for the Belgium,The Netherlands and NW Germany area

The algorithms to evaluate seismic hazard, used and/or developed by five teams participating in the TERESA project, applied to the low seismicity area Belgium, The Netherlands and NW Germany are compared. The main differences in the results can be explained by the majority criterion of Egozcue et al. (1989), the differences in the upper bound and zonification and, in some cases, by a higher attenuation.     

Infrared estimates of aliphatic kerogen carbon in sedimentary rocks

An infrared routine has been developed to estimate the aliphatic portion of kerogen carbon in sedimentary rocks. The procedure does not require isolation of the organic matter and is based on a computer-assisted determination of global band areas in the region of the aliphatic carbon-hydrogen stretching vibrations around 2900cm⁻¹. From these integrated absorptions the amount of aliphatic carbon C_al (mg of aliphatic carbon per gram of solvent-extracted rock) is calculated by means of a calibration with model rocks. Carbonate overtones which interfere in the case of limestones are eliminated by comparison to a CaCO₃ standard.The method has been applied to rocks containing kerogens of different types and maturities at TOC levels of 0.5 to 12%. The aliphatic carbon concentrations range from 0.5 to 60mg·g⁻¹ and correlate reasonably well with the residual genetic potentials of the rocks as measured by S₂ values from Rock-Eval pyrolysis. The ratio S₂/C_al is found to decrease with burial depth reflecting a maturity enhanced conversion of aliphatic carbon to fixed aromatic carbon under Rock-Eval conditions.     

Seismotectonic scheme of Central and Eastern Europe

Summary The distribution of earthquake foci in the crust and the upper mantle indicates the position of mobile zones. Comparing epicentral maps of Central and Eastern Europe, known tectonic lines, results of deep seismic sounding and gravimetric survey enables a scheme of potential seismogenic zones, which correspond to active fault zones separating plates and blocks in the area, to be compiled. The level of earthquake activity varies along the investigated boundaries and can be considered as a measure of the intensity of the present geodynamic processes.Paper presented at the joint symposium AlO of the XVIIth General Assembly of the European Seismological Commission and of the 7th Annual Meeting of the European Geophysical Society, Budapest (Hungary), Aug. 21. – 29., 1980.     

Time pattern of large earthquake sequences in Europe in 1976–1979

Summary The time development of three large sequences, Friuli 1976, Thessaloniki 1978 and Monte Negro-Albania 1979, was investigated by analysing the characteristics of the time distribution of magnitudes of the events, M(t), of average magnitudes, (t), and of the number of events, n(t), as well as the strain release curves and the magnitude-frequency relations, N(M). The existence of time gaps and of an anomalous decay of the numbers of shocks before major events, as well as the oscillation of ( const b^–1) may be considered as precursory phenomena. The clustering of events has been tested by the Poisson and negative binomial laws.Communication presented at the XVIIth General Assembly of the European Seismological Commission in Budapest, 21–29 August, 1980 under the title Properties of Seismic Regime and Recent Earthquake Sequences in Europe.     

Corrigenda

Corrigendum

Corrigenda     

Eine pleistozäne Rutschung bei Kitzbühel/Tirol

ZusammenfassungEine pleistozäne Rutschung bei Kitzbühel/Tirol Bei einem Grabenaushub wurden in Grundmoräne zwei fossile Rutschkörper festgestellt. Ein Beispiel wird anhand von alten Bewegungsstrukturen beschrieben, die durch Oxydationsstreifen abgebildet wurden. Nach dem Geländeschnitt rissen z. T. die alten Schwächestellen infolge geringer Abweichungen der Scherfestigkeit des Materials wieder auf.

---

SummaryA Pleistocene Landslide near Kitzbühel/Tyrol During excavation of a ditch two fossil landslides have been ascertained. One example is described the structures of which are copied by oxide bands. After excavating the old joints have opened again.

---

RésuméUn glissement pléistocène près de Kitzbühel/Tyrol Pendant l'excavation d'un fossé deux glissements fossiles étaient constatés dans la moraine. Un glissement est décrit dont les structures sont illustrées par bandes d'oxydes. Les observations ont demontré que les fissures vieilles se sont ouvertes après l'excavation.

---

---

Mit 1 Abbildung     

Validation of a model for impact breakage incorporating particle size effect

Investigation of a breakage probability model published by Vogel and Peukert [Vogel, L. and Peukert, W., 2004. Determination of material properties relevant to grinding by practicable labscale milling tests. Int. J. Miner. Process., 74S, 329–338.] has led to a modification of their model to describe the degree of impact breakage, t₁₀. The modified model takes a form similar to the JKMRC prior art breakage model, but with particle size and breakage properties incorporated explicitly in the model.