We designed a new seismic source model for Italy to be used as an input for country-wide probabilistic seismic hazard assessment (PSHA) in the frame of the compilation of a new national reference map.
We started off by reviewing existing models available for Italy and for other European countries, then discussed the main open issues in the current practice of seismogenic zoning.
The new model, termed ZS9, is largely based on data collected in the past 10 years, including historical earthquakes and instrumental seismicity, active faults and their seismogenic potential, and seismotectonic evidence from recent earthquakes. This information allowed us to propose new interpretations for poorly understood areas where the new data are in conflict with assumptions made in designing the previous and widely used model ZS4.
ZS9 is made out of 36 zones where earthquakes with Mw > = 5 are expected. It also assumes that earthquakes with Mw up to 5 may occur anywhere outside the seismogenic zones, although the associated probability is rather low. Special care was taken to ensure that each zone sampled a large enough number of earthquakes so that we could compute reliable earthquake production rates.
Although it was drawn following criteria that are standard practice in PSHA, ZS9 is also innovative in that every zone is characterised also by its mean seismogenic depth (the depth of the crustal volume that will presumably release future earthquakes) and predominant focal mechanism (their most likely rupture mechanism). These properties were determined using instrumental data, and only in a limited number of cases we resorted to geologic constraints and expert judgment to cope with lack of data or conflicting indications. These attributes allow ZS9 to be used with more accurate regionalized depth-dependent attenuation relations, and are ultimately expected to increase significantly the reliability of seismic hazard estimates. 相似文献
A crucial point in any methodology for avalanche hazard assessment is the evaluation of avalanche distance exceeded probability, i.e., the annual probability that any assigned location along a given path is reached or exceeded by an avalanche. Typically this problem is faced by estimating the snow volume in the starting zone that is likely to accumulate an average every T years by statistical analysis of snowfall record, and then using this volume as input to an appropriately calibrated avalanche dynamics model to determine the runout distancesfor this design event. This methodology identifies the areas that canbe affected by an avalanche for the considered value of the return period (i.e. the average interval of time for a certain event to repeat itself), ¯T. However, it does not allow us to evaluate the actual avalanche encounter probability for any given point in the runout zone. In the present work this probability is computed by numerical integration of the expression P(x) = ∫0∞ P*(V)f(V) dV, where f is the probabilitydensity function (PDF) of the avalanche release volume V, and P* is the probability of the point x being reached or passed by an avalanche if the release volume is V; this latter probability is calculated by avalanche dynamics simulations. The procedure is implemented using a one-dimensional hydraulic-continuum avalanche dynamic model, calibrated on data from different Italian Alpine ranges, and is applied to a real world hazard mapping problem. 相似文献
LIDAR (Light Detection and Ranging) is one of the most recent technologies in surveying and mapping. LIDAR is based on the combination of three different data collection tools: a laser scanner mounted on an aircraft, a Global Positioning System (GPS) used in phase differential kinematic modality to provide the sensor position and an Inertial Navigation System (INS) to provide the orientation. The laser sends towards the ground an infrared signal, which is reflected back to the sensor. The time employed by the signal, given the aircraft position and attitude, allows computation of the earth point elevation. In standard conditions, taking into account the flight (speed 200–250 km/hour, altitude 500–2,000 m) and sensor characteristics (scan angle ± 10–20 degrees, emission rate 2,000–50,000 pulses per second), earth elevations are collected within a density of one point every 0.5–3 m. The technology allows us therefore to obtain very accurate (5–20 cm) and high resolution Digital Surface Models (DSM). For many applications, the Digital Terrain Model (DTM) is needed: we have to automatically detect and discard from the previous DSM all the features (buildings, trees, etc.) present on the terrain. This paper describes a procedure that has been implemented within GRASS to construct DTMs from LIDAR source data. 相似文献
A multi‐method approach (palaeothermal and thermochronological analyses; thermal modelling) is applied to reconstruct the exhumation history of the Altotiberina Fault (ATF), a representative example of crustal‐scale active low‐angle normal faulting in the Northern Apennines (Italy). Thermal maturity and thermochronological data yield similar burial histories but different exhumation patterns for the sedimentary successions in the hangingwall and the footwall of the ATF. Since 3.8 Ma, the ATF footwall has exhumed at rates of 0.90 mm a?1. Exhumation led to bending and deactivation of the ATF uppermost portion as a result of tectonic unloading and isostatic adjustment, followed by migration of extension and the development of a set of domino‐like, east‐dipping normal faults, rooting on the buried portion of the ATF. ATF activity and isostatic rebound exhumed Triassic rock units from depths of about 4 km. We suggest that isostatic instability is accommodated at shallow crustal levels, in a similar way to what is observed on larger structures at mid‐low crustal levels. 相似文献
Computational Geosciences - Anthropogenic land subsidence can be evaluated and predicted by numerical models, which are often built over deterministic analyses. However, uncertainties and... 相似文献
Three Australian brown coals have been separated into humin and humic acid fractions and studied by high resolution solid state 13C NMR spectroscopy and Fourier transform IR spectroscopy. The aromatic rings of the humic acids are highly substituted showing that extensive cross linking must have occurred during formation from wood lignin and tannin. However, the humins contain more aliphatic carbon and hydrogen than the corresponding humic acids. This shows that little cross linking has occurred with other components of the brown coal such as resins, waxes cutin and algal detritus, and cross linking has not rendered the aromatics alkali insoluble. The kinetics of extraction are complex and not simple first order. This is reflected in the chemical composition of the humic acid which is extraction temperature dependent. We also observed that there is a conversion of aromatic carbon to aliphatic carbon and gas during extraction, probably by alkaline oxidation, resulting in ring opening. A range of suitable model compounds have been studied to confirm this finding. Such a mechanism may account for the modification of lignin in oxidising environments such as those occurring in the initial stages of coalification (lignite or brown coal formation) and in soils. 相似文献
The judicious choice of dipolar dephasing times or carbon magnetization holding times has been shown to improve resolution in solid state nuclear magnetic resonance (NMR) spectra of complex materials. Signals from protonated and alkylated aromatic carbons are reduced to enhance resolution of aromatic oxygenated groups. Rapidly rotating methyl groups can be resolved from other aliphatic carbon types. These techniques were used to investigate the structure of a brown coal, xylite fractions of a brown coal, a bituminous coal, an oil shale and a solvent-refined coal. The results allow estimates of the fraction of aromatic carbon that is protonated in coal to be made, and demonstrate that methyl groups in coal rotate rapidly at room temperature. 相似文献