Consolidation of double‐layered ground with vertical drains

Vertical drains are usually installed in subsoil consisting of several layers. Due to the complex nature of the problem, over the past decades, the consolidation properties of multi‐layered ground with vertical drains have been analysed mainly by numerical methods. An analytical solution for consolidation of double‐layered ground with vertical drains under quasi‐equal strain condition is presented in this paper. The main steps for the computation procedure are listed. The convergence of the series solution is discussed. The comparisons between the results obtained by the present analytical method and the existing numerical solutions are described by figures. The orthogonal relation for the system of double‐layered ground with vertical drains is proven. Finally, some consolidation properties of double‐layered ground with vertical drains are analysed. Copyright © 2001 John Wiley & Sons, Ltd.     

Three dimensional simulation of fluid flow in X‐ray CT images of porous media

A numerical scheme is developed in order to simulate fluid flow in three dimensional (3‐D) microstructures. The governing equations for steady incompressible flow are solved using the semi‐implicit method for pressure‐linked equations (SIMPLE) finite difference scheme within a non‐staggered grid system that represents the 3‐D microstructure. This system allows solving the governing equations using only one computational cell. The numerical scheme is verified through simulating fluid flow in idealized 3‐D microstructures with known closed form solutions for permeability. The numerical factors affecting the solution in terms of convergence and accuracy are also discussed. These factors include the resolution of the analysed microstructure and the truncation criterion. Fluid flow in 2‐D X‐ray computed tomography (CT) images of real porous media microstructure is also simulated using this numerical model. These real microstructures include field cores of asphalt mixes, laboratory linear kneading compactor (LKC) specimens, and laboratory Superpave gyratory compactor (SGC) specimens. The numerical results for the permeability of the real microstructures are compared with the results from closed form solutions. Copyright © 2004 John Wiley & Sons, Ltd.     

Relict mountain slope deposits of northern Portugal: facies,sedimentogenesis and environmental implications

This paper deals with the formation processes and the palaeoenvironmental significance of relict slope deposits located on the uppermost part of the north Portugal mountains. For this purpose, seven key sites representative of the different lithofacies have been selected and analysed in detail. The data show that three main dynamic processes are responsible for the emplacement of regional fossil slope deposits: runoff, debris flows and dry grain flows. The ubiquity of these processes and the lack of frost‐related features or landforms do not support the existence of severe Pleistocene climates in this part of the lberian Peninsula as postulated by previous work. Pedological data gathered at one of the study sites show that a subalpine environment was probably present at 700–800 m altitude between 29 and 14 kyr. Using data from the Pyrenees Mountains, a 6.5 to 12°C depression in mean annual temperature has been tentatively postulated for this Pleniglacial period. Copyright © 2003 John Wiley & Sons, Ltd.     

Bond rolling resistance and its effect on yielding of bonded granulates by DEM analyses

A discrete element modelling of bonded granulates and investigation on the bond effect on their behaviour are very important to geomechanics. This paper presents a two‐dimensional (2‐D) discrete element theory for bonded granulates with bond rolling resistance and provides a numerical investigation into the effect of bond rolling resistance on the yielding of bonded granulates. The model consists of mechanical contact models and equations governing the motion of bonded particles. The key point of the theory is that the assumption in the original bond contact model previously proposed by the authors (55th CSCE‐ASCE Conference, Hamilton, Ont., Canada, 2002; 313–320; J. Eng. Mech. (ASCE) 2005; 131 (11):1209–1213) that bonded particles are in contact at discrete points, is here replaced by a more reliable assumption that bonded particles are in contact over a width. By making the idealization that the bond contact width is continuously distributed with the normal/tangential basic elements (BE) (each BE is composed of spring, dashpot, bond, slider or divider), we establish a bond rolling contact model together with bond normal/tangential contact models, and also relate the governing equations to local equilibrium. Only one physical parameter β needs to be introduced in the theory in comparison to the original bond discrete element model. The model has been implemented into a 2‐D distinct element method code, NS2D. Using the NS2D, a total of 86 1‐D, constant stress ratio, and biaxial compressions tests have been carried out on the bonded granular samples of different densities, bonding strengths and rolling resistances. The numerical results show that: (i) the new theory predicts a larger internal friction angle, a larger yielding stress, more brittle behaviour and larger final broken contact ratio than the original bond model; (ii) the yielding stress increases nonlinearly with the increasing value of β, and (iii) the first‐yield curve (initiation of bond breakage), which define a zone of none bond breakage and which shape and size are affected by the material density, is amplified by the bond rolling resistance in analogous to that predicted by the original bond model. Copyright © 2006 John Wiley & Sons, Ltd.     

Effect of spatial variation characteristics on contouring of design storm depth

The ordinary kriging method, a geostatistical interpolation technique, was applied for developing contour maps of design storm depth in northern Taiwan using intensity–duration–frequency (IDF) data. Results of variogram modelling on design storm depths indicate that the design storms can be categorized into two distinct storm types: (i) storms of short duration and high spatial variation and (ii) storms of long duration and less spatial variation. For storms of the first category, the influence range of rainfall depth decreases when the recurrence interval increases, owing to the increasing degree of their spatial independence. However, for storms of the second category, the influence range of rainfall depth does not change significantly and has an average of approximately 72 km. For very extreme events, such as events of short duration and long recurrence interval, we do not recommend usage of the established design storm contours, because most of the interstation distances exceed the influence ranges. Our study concludes that the influence range of the design storm depth is dependent on the design duration and recurrence interval and is a key factor in developing design storm contours. Copyright © 2003 John Wiley & Sons, Ltd.     

Elastic solutions for stresses in a transversely isotropic half‐space subjected to three‐dimensional buried parabolic rectangular loads

In many areas of engineering practice, applied loads are not uniformly distributed but often concentrated towards the centre of a foundation. Thus, loads are more realistically depicted as distributed as linearly varying or as parabola of revolution. Solutions for stresses in a transversely isotropic half‐space caused by concave and convex parabolic loads that act on a rectangle have not been derived. This work proposes analytical solutions for stresses in a transversely isotropic half‐space, induced by three‐dimensional, buried, linearly varying/uniform/parabolic rectangular loads. Load types include an upwardly and a downwardly linearly varying load, a uniform load, a concave and a convex parabolic load, all distributed over a rectangular area. These solutions are obtained by integrating the point load solutions in a Cartesian co‐ordinate system for a transversely isotropic half‐space. The buried depth, the dimensions of the loaded area, the type and degree of material anisotropy and the loading type for transversely isotropic half‐spaces influence the proposed solutions. An illustrative example is presented to elucidate the effect of the dimensions of the loaded area, the type and degree of rock anisotropy, and the type of loading on the vertical stress in the isotropic/transversely isotropic rocks subjected to a linearly varying/uniform/parabolic rectangular load. Copyright © 2002 John Wiley & Sons, Ltd.     

The influence of a non‐associated flow rule on the calculation of the factor of safety of soil slopes

This paper presents a method that incorporates a non‐associated flow rule into the limit analysis to investigate the influence of the dilatancy angle on the factor of safety for the slope stability analysis. The proposed method retain's the advantage of the upper bound method, which is simple and has no stress involvement in the calculation of the energy dissipation and the factor of safety. Copyright © 2001 John Wiley & Sons, Ltd.     

Depositional and post‐depositional history of warm stage deposits at Knocknacran,Co. Monaghan,Ireland: implications for preservation of Irish last interglacial deposits

Organic‐rich deposits, uncovered during overburden removal from mantled gypsum karst at Knocknacran opencast gypsum mine, Co. Monaghan, are the best candidate to date for a last interglacial record in Ireland. The two till and organic‐rich deposits (preserved at different quarry elevations) were emplaced on to a Tertiary dolerite surface during high‐energy flood events and subsequently folded and faulted by movement towards sinkholes in underlying gypsum. Uranium–thorium disequilibrium dating suggests that the organic‐rich deposits in the upper section were hydrologically isolated at ca. 41 ka and those in the lower section at ca. 86 ka. Interpretation of the pollen content, although tentative because of the depositional and post‐depositional history of the material, suggests that the organic material originated in a warm stage possibly warmer than the post‐Eemian interstadials. The unusual setting of preservation may indicate that in situ, last interglacial deposits have generally been removed by erosion in Ireland. Copyright © 2004 John Wiley & Sons, Ltd.     

FITS、BMP和SCR图象格式及相互转换

本文详细介绍图象的ＦＩＴＳ格式、ＢＭＰ格式和ＳＣＲ格式。ＦＩＴＳ格式已经是天文界的通用格式，几乎所有的天文软件包都支持这一格式，而ＢＭＰ格式在ＰＣ计算机上有广泛的运用，有大量ＰＣ软件支持ＢＭＰ图象的显示，处理和打印。云南天文台的ＳＣＲ格式是ＰＣ机采集ＣＣＤ图象所使用的格式。实现这三种格式的相互转换，就可以自由的将ＣＣＤ图象在ＰＣ机和工作站上进行各种处理。转换的包括图象头和图象数据的转换，其关键在于交换数据的高低字节。     

Simulating methane emission from a Chinese rice field as influenced by fertilizer and water level

Natural and agricultural wetlands are considered to be the major sources of global atmospheric methane (CH₄). A one‐dimensional model was developed to simulate methane emission and used to examine the influence of various physical processes on the rate of methane emission. Three processes involved in the methane emission are implemented in the model: production, reoxidation and transport. Three transport pathways were considered: diffusion across water–air or soil–air interfaces, ebullition and diffusion through plants. These pathways are influenced by soil properties, plant growth, water‐table conditions, temperature and external inputs (e.g. fertilizer). The model was used to examine the seasonal variation of the methane emission at a rice field in Hunan, China, which was observed during a field experiment for consecutive (early and late) rice seasons in 1992. The observed seasonal variations of methane emission, and role of plants in transporting methane to the atmosphere, are captured by the model simulation. Further model applications were conducted to simulate effects of fertilizer and water‐level condition on the methane emission. The results indicate that unfermented organic fertilizer produces a higher methane emission rate than mineral fertilizer. The simulations with treatments of a deep‐water covering and constant moisture reduced the methane emission. The rice field study provides a framework for further development of the model towards simulations based on spatially distributed variables (e.g. water table, soil temperature and vegetation) at a regional scale. Copyright © 2003 John Wiley & Sons, Ltd.