Analysis of pressuremeter geometry effects in clay using critical state models

The conventional interpretation methods of pressuremeter testing effectively approximate pressuremeter membranes as infinitely long. As a result, the effects of the two‐dimensional geometry of pressuremeters are ignored, leading to an overestimation of soil shear strength by pressuremeter testing, as demonstrated in several previous studies. This paper presents results of a numerical study of two‐dimensional geometry effects on self‐boring pressuremeter tests in undrained clay. The results are obtained using critical state soil models with an effective stress formulation. This is in contrast to most (if not all) existing studies on pressuremeter geometry effects, which were based on perfectly plastic soil models (e.g. Yu (Cavity expansion theory and its application to the analysis of pressuremeters. DPhil Thesis, The University of Oxford, 1990), Yeung and Carter (Proc. 3rd Int. Symp. on Pressuremeters, 1990), and Houlsby and Carter (Géotechnique, 1993; 43 (4):567–576)). The present study suggests that the overestimation of soil strength due to the neglect of finite pressuremeter length is significantly affected by the soil model used in the calculations. It is found that for clays with a high overconsolidation ratio (OCR) the strength overestimation predicted using critical state soil models could be considerably smaller than that predicted using perfectly plastic soil models. The main conclusion of this numerical study is that care must be exercised before directly applying any numerically determined pressuremeter geometry correction factors in practice. Copyright © 2005 John Wiley & Sons, Ltd.     

Prediction of creep characteristic of rock under varying environment

The strain developed due to creep is mainly proportional to the logarithm of the time under load, and is mostly proportional to the stress and temperature. At higher temperature the creep rate falls slowly with respect to time, and the creep strain is proportional to a fractional power of time, with the exponent increasing as the temperature increases and reaching a value approximately one-third at temperatures of about 0.5°C. At these temperatures, the creep increases with stress according to a power greater than unity and possibly exponentially. It increases with temperature as (−U/kT), where U is an activation energy and k is Boltzman’s constant. There are different methods to determine the creep strain and the energy of Jog (B) including experimental methods, multivariate regression analysis, and by numerical simulation. These methods are less cumbersome and time consuming. In the present investigation, artificial neural network technique has been used for prediction of the creep strain and energy of Jog (B). Two different networks have been tested and validated. Both the networks have four input neurons and one hidden layer with five neurons, and one output neuron. The data for different rocks at temperatures up to 750°C under conditions of compressive or tortional stress are taken from the literatures. The training and testing data sets used were 163 and 14, respectively. To deal with the problem of overfitting of data, Bayesian regulation has been used and network is trained with suitable training epochs. The coefficients of correlation among the predicted and observed values are found high and they improve the confidence of the users. The mean absolute percentage error obtained are also very low.     

Development of a soil moisture‐based distributed hydrologic model for determining hydrologically based critical source areas

A simple grid cell‐based distributed hydrologic model was developed to provide spatial information on hydrologic components for determining hydrologically based critical source areas. The model represents the critical process (soil moisture variation) to run‐off generation accounting for both local and global water balance. In this way, it simulates both infiltration excess run‐off and saturation excess run‐off. The model was tested by multisite and multivariable evaluation on the 50‐km² Little River Experimental Watershed I in Georgia, U.S. and 2 smaller nested subwatersheds. Water balance, hydrograph, and soil moisture were simulated and compared to observed data. For streamflow calibration, the daily Nash‐Sutcliffe coefficient was 0.78 at the watershed outlet and 0.56 and 0.75 at the 2 nested subwatersheds. For the validation period, the Nash‐Sutcliffe coefficients were 0.79 at the watershed outlet and 0.85 and 0.83 at the 2 subwatersheds. The per cent bias was less than 15% for all sites. For soil moisture, the model also predicted the rising and declining trends at 4 of the 5 measurement sites. The spatial distribution of surface run‐off simulated by the model was mainly controlled by local characteristics (precipitation, soil properties, and land cover) on dry days and by global watershed characteristics (relative position within the watershed and hydrologic connectivity) on wet days when saturation excess run‐off was simulated. The spatial details of run‐off generation and travel time along flow paths provided by the model are helpful for watershed managers to further identify critical source areas of non‐point source pollution and develop best management practices.     

A cavity expansion–based solution for interpretation of CPTu data in soils under partially drained conditions

A cavity expansion–based solution is proposed in this paper for the interpretation of CPTu data under a partially drained condition. Variations of the normalized cone tip resistance, cone factor, and undrained-drained resistance ratio are examined with different initial specific volume and overconsolidation ratio, based on the exact solutions of both undrained and drained cavity expansion in CASM, which is a unified state parameter model for clay and sand. A drainage index is proposed to represent the partially drained condition, and the critical state after expansion and stress paths of cavity expansion are therefore predicted by estimating a virtual plastic region and assuming a drainage-index–based mapping technique. The stress paths and distributions of stresses and specific volume are investigated for different values of drainage index, which are also related to the penetration velocity with comparisons of experimental data and numerical results. The subsequent consolidation after penetration is thus predicted with the assumption of constant deviatoric stress during dissipation of the excess pore pressure. Both spherical and cylindrical consolidations are compared for dissipation around the cone tip and the probe shaft, respectively. The effects of overconsolidation ratio on the stress paths and the distributions of excess pore pressure and specific volume are then thoroughly investigated. The proposed solution and the findings would contribute to the interpretation of CPTu tests under a random drained condition, as well as the analysis of pile installation and the subsequent consolidation.     

Three-dimensional active earth pressure from cohesive backfills with tensile strength cutoff

Most of previous analyses on the active earth pressure were performed in two-dimensional cases using the Mohr-Coulomb (M-C) failure function to describe the soil strength. However, all failures of retained slopes indicate a somewhat three-dimensional (3D) feature, and the M-C function is found to overestimate the tensile strength of cohesive soil. In this work, a kinematic limit analysis–based approach is developed for computing the 3D active earth pressure resulting from cohesive backfills. The concept of tensile strength cutoff is adopted to implement the reduction or elimination of tensile strength from the strength envelope. An extended 3D horn failure mechanism that is associated with the modified strength envelope is developed to characterize the collapse of retained slopes. The resultant of active earth pressure is evaluated from the work rate balance equation and expressed as an unfactored coefficient. The obtained results indicate that less support provided by the wall is required when allowing the existence of soil cohesion and 3D effects and that eliminating the tensile strength can observably increase the active earth pressure, especially for the backfill with a great level of cohesion.     

Stability analysis of tunnels driven in jointed rocks by means of a homogenized limit analysis approach

Conceived as a potential alternative to the classical design methods employed for analyzing the stability of underground structures driven in jointed rocks, the homogenization approach stems from the heuristic idea that, from a macroscopic point of view, a rock mass cut by a network of joints may be perceived as a homogenized continuum. The strength properties of the latter can be theoretically obtained from the failure conditions of its individual constituents: rock matrix and joint interfaces. At the material level, the limit analysis reasoning is used in the context of homogenization to formulate the homogenized strength criterion of a jointed rock mass in the particular situation of a single set of parallel joints. As it could be expected, the obtained closed‐form expressions show the strength anisotropy induced by joint preferential orientation. The support functions (π functions) associated with the homogenized strength criterion are also determined in both plane strain and three‐dimensional cases. This criterion is then applied to the investigation of stability analysis of a tunnel excavated in a jointed rock mass. Upper bounds estimated of the stability factor are derived from the implementation of the kinematic approach directly on the homogenized underground structure. Finally, the approach is applied to analyze and discuss the collapse of the Pinheiros subway station (São Paulo, Brazil). Copyright © 2014 John Wiley & Sons, Ltd.     

Mechanical transitional behavior of binary mixtures via DEM: Effect of differences in contact-type friction coefficients

This report presents a numerical investigation of the shear behavior of binary mixtures via a two-dimensional discrete element method. The effect of the coarse particle content on the peak shear strength of mixtures is investigated for different contact-type friction coefficients. A detailed analysis on the anisotropies enables us to understand the microscopic mechanisms that result in the dependency of the peak shear strengths on the coarse particle content. The contributions of different contact types to the peak shear strength are quantified. Lastly, the inter-particles structures are examined when the binary mixtures become coarse-particle-supported structures.     

From soil aggregates to riverine flocs: a laboratory experiment assessing the respective effects of soil type and flow shear stress on particles characteristics

Particles eroded from hillslopes and exported to rivers are recognized to be composite particles of high internal complexity. Their architecture and composition are known to influence their transport behaviour within the water column relative to discrete particles. To‐date, hillslope erosion studies consider aggregates to be stable once they are detached from the soil matrix. However, lowland rivers and estuaries studies often suggest that particle structure and dynamics are controlled by flocculation within the water column. In order to improve the understanding of particle dynamics along the continuum from hillslopes to the lowland river environment, soil particle behaviour was tested under controlled laboratory conditions. Seven flume erosion and deposition experiments, designed to simulate a natural erosive event, and five shear cell experiments were performed using three contrasting materials: two of them were poorly developed and as such can not be considered as soils, whilst the third one was a calcareous brown soil. These experiments revealed that soil aggregates were prone to disaggregation within the water column and that flocculation may affect their size distribution during transport. Large differences in effective particle size were found between soil types during the rising limb of the bed shear stress sequence. Indeed, at the maximum applied bed shear stress, the aggregated particles median diameter was found to be three times larger for the well‐developed soil than for the two others. Differences were smaller in the falling limb, suggesting that soil aggregates underwent structural changes. However, characterization of particles strength parameters showed that these changes did not fully turn soil aggregates into flocs, but rather into hybrid soil aggregate–floc particles. Copyright © 2013 John Wiley & Sons, Ltd.     

Spatial and temporal variability of stable isotopes (δ18O and δ2H) in surface waters of arid,mountainous Central Asia

Characterization of spatial and temporal variability of stable isotopes (δ¹⁸O and δ²H) of surface waters is essential to interpret hydrological processes and establish modern isotope–elevation gradients across mountainous terrains. Here, we present stable isotope data for river waters across Kyrgyzstan. River water isotopes exhibit substantial spatial heterogeneity among different watersheds in Kyrgyzstan. Higher river water isotope values were found mainly in the Issyk‐Kul Lake watershed, whereas waters in the Son‐Kul Lake watershed display lower values. Results show a close δ¹⁸O–δ²H relation between river water and the local meteoric water line, implying that river water experiences little evaporative enrichment. River water from the high‐elevation regions (e.g., Naryn and Son‐Kul Lake watershed) had the most negative isotope values, implying that river water is dominated by snowmelt. Higher deuterium excess (average d = 13.9‰) in river water probably represents the isotopic signature of combined contributions from direct precipitation and glacier melt in stream discharge across Kyrgyzstan. A significant relationship between river water δ¹⁸O and elevation was observed with a vertical lapse rate of 0.13‰/100 m. These findings provide crucial information about hydrological processes across Kyrgyzstan and contribute to a better understanding of the paleoclimate/elevation reconstruction of this region.     

Alteration of hydrological processes and streamflow with juniper (Juniperus virginiana) encroachment in a mesic grassland catchment

To understand the effect of woody plant encroachment on hydrological processes of mesic grasslands, we quantified infiltration capacity in situ, the temporal changes in soil water storage, and streamflow of a grassland catchment and a catchment heavily encroached by juniper (Juniperus virginiana, eastern redcedar) in previously cultivated, non‐karst substrate grasslands in north‐central Oklahoma for 3 years. The initial and steady‐state infiltration rates under the juniper canopy were nearly triple to that of the grassland catchment and were intermediate in the intercanopy spaces within the encroached catchment. Soil water content and soil water storage on the encroached catchment were generally lower than on the grassland catchment, especially when preceding the seasons of peak rainfall in spring and fall. Frequency and magnitude of streamflow events were reduced in the encroached catchment. Annual runoff coefficients for the encroached catchment averaged 2.1%, in contrast to 10.6% for the grassland catchment. Annual streamflow duration ranged from 80 to 250 h for the encroached catchment compared with 600 to 800 h for the grassland catchment. Our results showed that the encroachment of juniper into previously cultivated mesic grasslands fundamentally alters catchment hydrological function. Rapid transformation of mesic grassland to a woodland state with juniper encroachment, if not confined, has the potential to drastically reduce soil water, streamflow and flow duration of ephemeral streams in the Southern Great Plains. Copyright © 2013 John Wiley & Sons, Ltd.