复合体系有机气体氧化生成二次有机气溶胶研究进展

生物源与人为源有机气体氧化形成的二次有机气溶胶(SOA)对气候变化和人类健康具有重要影响。SOA的产生与其前体物研究已取得了一些进展,但由于有机气体之间存在复合相互作用以及SOA形成机制复杂,目前对不同有机气体混合体系中SOA的形成认知还比较匮乏。因此,深入了解有机气体多源、复杂的相互作用,摸清有机气体的大气氧化机制、SOA的形成及影响等对深入理解真实大气有机气体化学演变具有指导意义。本文旨在了解复合体系有机气体氧化生成SOA的相关研究进展。一方面总结了复合体系有机气体产生SOA质量浓度、产率、成分、挥发性、光学性质等的变化,侧重于实验室复合体系有机气体氧化对SOA形成的多重影响以及SOA组成元素、分子构成的变化特征,并总结了目前实验室基于模型对复合体系SOA生成的模拟研究和拟合情况;另一方面探究了环境因素,如相对湿度(RH)、温度(T)以及无机气体,如氮氧化物(NO_x)、二氧化硫(SO₂)、氨气(NH₃)等对复合体系有机气体形成SOA的影响。     

三峡库首区重点断裂围限区蓄水的加卸载效应

通过对蓄水前后三峡库首区构造应力场进行三维数值模拟发现,相对于蓄水前,蓄水至135 m水位时,官渡口断裂-马鹿池断裂-牛口断裂围限区、秭归地理中心和九湾溪断裂带,出现了4个主应力下降区和共轭的主应力增长区,形成了差应力场;175 m水位与135 m水位相比,局部差应力场呈现逆向变化,即形成了加载效应与卸载效应的交替过程。这一过程,可能是水库诱发地震的诱震(或触震)因素。     

不同水沙条件下黄河下游二级悬河的发展过程

以大量实测横断面资料为基础,研究了1973~1997年不同水沙过程对黄河下游二级悬河形成过程的影响。发现花园口至高村河段二级悬河集中形成于1985~1997年的枯水阶段。高村以下河段二级悬河的形成可分两个阶段,1973~1985年大水条件下是冲刷主槽和淤积滩地的时期,但是由于泥沙主要堆积在靠近滩唇的部位,造成河床横比降增大;1985~1997年枯水条件下泥沙在主槽中大量淤积,导致二级悬河的形势更加严重。生产堤限制了泥沙的堆积范围,导致生产堤内滩地平均高程增长速度明显快于生产堤外滩地平均高程增长速度,生产堤距较窄的河段生产堤内滩地平均高程增长速度较快,显示了生产堤对二级悬河的发展有促进作用。     

ATTEM系统中电流关断期间瞬变电磁场响应求解的研究

在瞬变电磁法中,由于发射电流关断时间不为零、接收线圈的谐振频率有限,早期瞬变电磁信号发生畸变,只能舍弃,因此存在着探测盲区. 针对这一问题,研究了瞬变电磁方法中发射电流关断期间总磁场的形成过程,论证了一次场、二次场和总瞬变场的关系,分析了接收线圈的频率特性和关断时间对瞬变电磁场的影响,提出从总磁场中剔除一次磁场影响的方法,从而获得电流关断期间和电流关断后的早期瞬变电磁场. 采用吉林大学自主研制的瞬变电磁测量系统(ATTEM)在长春市伊通河活断层进行勘探,进一步验证了算法的有效性,缩短了瞬变电磁法的勘探盲区,实现了近地表4 m以下的勘探,可以清晰地分辨近地表的低阻异常,提高了浅层探测精度和分辨率.     

白云岩成因相关问题及主要形成模式

在综述白云岩成因研究历程和最新成果的基础上,总结阐述了与之相关的4个方面的问题:①尽管白云岩原生沉淀与次生交代成因分歧依旧,但越来越多的证据表明白云岩的形成以次生交代为主;②白云石难以直接沉淀的原因是受结晶动力学条件制约,而非热力学因素;③控制次生交代强度和规模的关键条件是富Mg流体的来源及其量的大小;④微生物活动很可能有助于白云岩的形成。关于白云岩化模式,其核心是构建富Mg流体与先成钙质碳酸盐岩相互作用的条件与场所,其中浓缩正常海水模式、萨布哈模式、混合水模式和埋藏白云岩化模式等具有一定的普遍性。理清白云岩成因问题,对于认识以白云岩及其相关的碳酸盐岩为储层的油气勘探工作尤为重要。     

中国地震次生地质灾害危险性评价

地震次生地质灾害主要指地震引起的崩塌、滑坡、塌陷、地裂缝、砂土液化。震级大于5级、烈度超过Ⅵ度的地震可能引发不同程度的地质灾害,震级和烈度越高,次生地质灾害越严重。本文根据中国历史地震次生地质灾害活动程度及发生条件,以地(市、区、盟)为单元,进行了危险性评价:高度和中度危险区主要分布在中国中部的陕甘宁川渝滇藏地区,形成一个大致NE向高危险带,其余大部分地区为轻度危险区。      

渤海大型底栖动物次级生产力的初步研究

1998年 9月和 1999年 4月分别对渤海 2 0个站进行了大型底栖动物两个航次的调查取样。整个研究海域大型底栖动物年次级生产力平均值为 6 .4 9g(AFDW) /(m2 · a) ,其中渤海海峡以东海域较高 ,为 12 .5 9g(AFDW) /(m2· a) ;渤海中部为 4 .4 6 g(AFDW) /(m2· a) ,渤海大型底栖动物年平均 P/B为 0 .82     

Theoretical aspects of cap-rock and fault seals for single- and two-phase hydrocarbon columns

Cap-rock seals can be divided genetically into those that fail by capillary leakage (membrane seals) and those whose capillary entry pressures are so high that seal failure preferentially occurs by fracturing and/or wedging open of faults (hydraulic seals). A given membrane seal can trap a larger oil column than gas column at shallow depths, but below a critical depth (interval), gas is more easily sealed than oil. This critical depth increases with lower API gravity, lower oil GOR and overpressured conditions (for the gas phase). These observations arise from a series of modelling studies of membrane sealing and can be conveniently represented using pressure/ depth (P/D) profiles through sealed hydrocarbon columns. P/D diagrams have been applied to the more complex situation of the membrane sealing of a gas cap underlain by an oil rim; at seal capacity, such a two-phase column will be always greater than if only oil or gas occurs below the seal.These conclusions contrast with those for hydraulic seals where the seal capacity to oil always exceeds that for gas. Moreover, a trapped two-phase column, at hydraulic seal capacity will be less than the maximum-allowed oil-only column, but more than the maximum gas-only column. Unlike membrane seals, hydraulic seal capacity should be directly related to cap-rock thickness, in addition to the magnitude of the minimum effective stress in the sealing layer and the degree of overpressure development in the sequence as a whole.Fault-related seals are effectively analogous to membrane cap-rocks which have been tilted to the angle of the fault plane. Consequently, all of the above conclusions derived for membrane cap-rocks apply to both sealing faults sensu stricto (fault plane itself seals) and juxtaposition faults (hydrocarbon trapped laterally against a juxtaposed sealing unit). The maximum-allowed two-phase column trapped by a sealing fault is greater than for equivalent oil-only and gas-only columns, but less than that predicted for a horizontal membrane cap-rock under similar conditions. Where a two-phase column is present on both sides of a sealing fault (which is at two-phase seal capacity), a deeper oil/water contact (OWC) in one fault block is associated with a deeper gas/oil contact (GOC) compared with the adjacent fault block. If the fault seal is discontinuous in the gas leg, however, the deeper OWC is accompanied by a shallower GOC, whereas a break in the fault seal in the oil leg results in a common OWC in both fault blocks, even though separate GOC's exist. Schematic P/D profiles are provided for each of the above situations from which a series of fundamental equations governing single- and two-phase cap-rock and fault seal capacities can be derived. These relationships may have significant implications for exploration prospect appraisal exercises where more meaningful estimates of differential seal capacities can be made.The membrane sealing theory developed herein assumes that all reservoirs and seals are water-wet and no hydrodynamic flow exists. The conclusions on membrane seal capacity place constraints on the migration efficiency of gas along low-permeabiligy paths at depth where fracturing, wedging open of faults and/or diffusion process may be more important. Contrary to previous assertions, it is speculated that leakage of hydrocarbons through membrane seals occurs in distinct pulses such that the seal is at or near the theoretically calculated seal capacity, once this has been initially attained.Finally, the developed seal theory and P/D profile concepts are applied to a series of development geological problems including the effects of differential depletion, and degree of aquifer support, on sealing fault leakage, and the evaluation of barriers to vertical cross-flow using RFT profiles through depleted reservoirs. It is shown that imbibition processes and dynamic effects related to active cross-flow across such barriers often preclude quantitative analysis and solution of these problems for which simulation studies are usually required.     

长江口及其邻近海域大型底栖动物生物量、丰度和次级生产力的初步研究

为了解长江口及邻近海域大型底栖动物生物量、丰度和次级生产力的分布情况于2004年2月、5月、8月和11月共4个航次分别在长江口40个观测站采集大型底栖动物定量样品并利用Brey的经验公式对大型底栖动物栖息丰度、生物量、次级生产力和P/B值进行了研究计算.该调查海域共采到大型底栖动物202种,其中多毛类102种,软体动物51种,甲壳类27种,棘皮动物7种,其它动物15种.大型底栖动物年平均丰度为394.7 ind/m2;年平均生物量以去灰分干重计,为2.58 g(AFDW)/m2;年平均次级生产力以去灰分干重计,为3.52 g(AFDW)/(m2*a);P/B值平均为1.53.结果表明,长江口大型底栖动物次级生产力自长江入海口向东呈递增趋势.本文分析了长江口及其邻近海域大型底栖动物优势种的组成,主要生态类群的分布特征和次级生产力分布格局与生态环境的关系.通过比较,发现长江口大型底栖动物优势种发生了较大的变化;次级生产力高于东海而低于渤海和胶州湾;P/B值高于南黄海、胶州湾和渤海,也说明了长江口大型底栖动物群落中个体小、生活史短,代谢快的种类所占的比例高于以上海域.     

基于多元统计分析的渔山列岛潮间带软体动物功能群和次级生产力比较

渔山列岛于2008年成为国家级海洋生态保护区,为了解渔山列岛保护区内潮间带软体动物次级生产力的时空变化。于1982年和2010年的3个季节(春、夏、冬)在渔山列岛进行潮间带软体动物调查,采用多元统计分析软体动物时空差异,以Brey经验公式计算分析软体动物次级生产力(P值,P/B值)。结果表明,年际间物种食性结构发生了明显的改变,1982年潮间带软体动物对次级生产力贡献率最大的物种有单齿螺(Monodonta labio)、锈凹螺(Chlorostoma rustica),占软体动物总次级生产力的42.88%,2010年潮间带软体动物对次级生产力贡献率最大的物种有覆瓦小蛇螺(Serpulorbis imbricata)、条纹隔贻贝(Septifer virgatus),占软体动物总次级生产力的75.96%。1982年,年均栖息密度为2758ind/m2,年均生物量为2100.26g/m2,年均次级生产力为240.04g/(m2·a),年均P/B值为0.63a–1;2010年,年均栖息密度为699ind/m2,年均生物量为1101.85g/m2,年均次级生产力为94.82g/(m2·a),年均P/B值为0.55a–1。多因素方差分析表明软体动物次级生产力年际间差异显著(F=5.761,P0.05),季节间和潮位间差异都不显著(F=0.135,P0.05;F=2.076,P0.05),P/B的值较低,表明该海域软体动物世代更替速度较慢,2010年的P/B值(0.55a–1)低于1982年的P/B值(0.63a–1),表明近30年来群落结构受到影响。