不同弹模时圆形巷道围岩的应变局部化数值模拟

利用基于运动方程求解的FLAC程序模拟了不同弹性模量时圆形巷道的应变局部化过程。在计算中, 采用了"先加载, 后挖洞"方式。模拟结果表明, 在弹性模量中等或较小的条件下, 由于开挖卸荷而产生的围岩向空腔内部的"涌入"(运动)现象比较明显, 进而围岩中诱发了较多的破坏、V形坑或短剪切带式破坏。在上述条件下, 基于静力平衡的解析及数值方法不再适用, 而且是偏于不安全的。弹性模量越小, 开挖之后, 围岩维持其均匀周向(或环向)变形的能力越差, 这种轴对称变形越容易被打破, 也被打破得越早。尽管随着弹性模量的增加, 破坏单元数的变化并不是单调的, 但是在总体上, 随着弹性模量的增加, 破坏单元数目降低, 最大剪切应变增量急剧单调下降。      

Comparison of continuous and discontinuous constitutive models to simulate concrete behaviour under mixed‐mode failure conditions

The paper presents detailed FE simulation results of concrete elements under mixed‐mode failure conditions according to the so‐called shear‐tension test by Nooru‐Mohamed, characterized by curved cracks. A continuous and discontinuous numerical two‐dimensional approach was used. In order to describe the concrete's behaviour within continuum mechanics, two different constitutive models were used. First, an elasto‐plastic model with isotropic hardening and softening was assumed. In a compression regime, a Drucker–Prager criterion with a non‐associated flow rule was used. In turn, in a tensile regime, a Rankine criterion with an associated flow rule was adopted. Second, an isotropic damage constitutive model was applied with a single scalar damage parameter and different definitions of the equivalent strain. Both constitutive laws were enriched by a characteristic length of micro‐structure to capture properly strain localization. As an alternative approach, the extended finite element method was used. Our results were compared with the experimental ones and with results of other FE simulations reported in the literature. Copyright © 2015 John Wiley & Sons, Ltd.     

The effect of pre‐tectonic reaction and annealing extent on behaviour during subsequent deformation: insights from paired shear zones in the lower crust of Fiordland,New Zealand

Granulite facies pargasite orthogneiss is partially to completely reacted to garnet granulite either side of narrow (<20 mm) felsic dykes, in Fiordland, New Zealand, forming ~10–80 mm wide garnet reaction zones. The metamorphic reaction changed the abundance of minerals, and their shape and grain size distribution. The extent of reaction and annealing (temperature‐related coarsening and nucleation) is greatest close to the dykes, whereas further away the reaction is incomplete. As a consequence, grain size and the abundance of garnet decreases away from the felsic dykes over a few centimetres. The aspect ratios of clusters of S1 pyroxene and pargasite in the orthogneiss, which are variably reacted to post‐S1 garnet, decrease from high in the host, to near equidimensional close to the dyke. Post‐reaction deformation localized in the fine‐grained partially reacted areas. This produced a pattern of ‘paired’ shear zones located at the outer parts of the garnet reaction zone. Our study shows that grain size sensitive deformation occurs where the grain size is sufficiently reduced by metamorphic reaction. The weakening of the rock due to the change in grain size distribution outweighs the addition of nominally stronger garnet to the assemblage.     

再议走滑断裂与地震孕育和发生条件

走滑断裂是与大地震关系最紧密的活动断裂带。研究走滑断裂带上大地震是如何孕育和发生的是地震学家们极为关心的问题。构造地质学研究表明,走滑断裂是一个复杂的构造系统,反映了在剪切作用下产生的各类变形组合。文中立足于国内外不同走滑断裂带实例,对连续或不连续走滑断裂的几何学、运动学和演化过程进行了研究和总结;分析了走滑断裂的枢纽作用,发现枢纽轴部强烈挤压,形成闭锁,应力在此集中,应变在此局部化,地震在此成核和孕育。当闭锁的枢纽轴被突破时,沿走滑断裂发生失稳错动,产生突发性大位移,伴随大地震发生。而在不连续走滑断裂不同性质的阶区,则遵循其相应的应力场和破裂机制孕育和发生相应规模和类型的地震。     

汶川8.0级地震地表变形局部化样式与建筑物破坏特征关系初步研究

以汶川地震地表形变带的实地测量数据为基础,结合沿实测地震地表变形剖面建筑物破坏情况的调查与测量,分析了不同地震地表变形类型及其建筑物破坏特征,定量化地讨论了地表变形梯度与建筑物破坏程度间的关系.提出无论地震地表变形表现为何种类型的断层陡坎,强变形均局部化在宽10~30 m的地表破裂带内;建筑物受损情况最直接的影响是建筑物所处地点的地表变形梯度,地表变形梯度大于0.1的地段,建筑物均完全被摧毁;地表变形梯度在0.07~0.1间的地段,建筑物遭受严重损坏,产生倾斜及强烈变形等;地表变形梯度在0.03~0.07间的地段,建筑物可能受到中度损坏,产生倾斜及变形等,具有抗震设防能力的建筑物一般不会倒塌;地表变形梯度小于0.03的地段具有抗震设防能力的构建筑物一般只会受到轻度损伤或基本完好.     

地质体材料剪切带内部的常剪切应变点及速度分布分析

对于峰后线性应变软化的地质体材料,剪切带内部的总剪切应变等于弹性剪切应变（由经典弹性理论描述）及由微结构效应而引起的局部塑性剪切应变（由非局部理论或梯度塑性理论描述）之和。若剪切应力-塑性剪切应变曲线的斜率的绝对值（称之为软化模董）小于剪切弹性模量的两倍,则在剪切带的任一剖面内存在两个总剪切应变不依赖于剪切应力的点,称之为常剪切应变点。在这两个点上,弹性剪切应变的降低和局部塑性剪切应变的增加处于平衡状态,总剪切速度达到它的最大值或最小值。在两个常剪切应变点之间,局部总速度随剪切应力率的降低而增加。剪切带内部的局部总速度分布是非线性的,这与通常采用的剪切带内部速度的线性分布假定（忽略微结构效应）不同。     

Identification of damage in reinforced concrete structures from earthquake records- optimal location of sensors

A method for the localization of structural damage in seismically excited reinforced concrete (RC) structures using a measured acceleration response time series is presented. From the measured response of some or all storeys, the two lowest smoothed eigenfrequencies and mode shape coordinates are estimated. These estimated values are used as an input to a developed substructure iteration method where local storey damages are estimated in such a way that these smoothed values are reproduced. The local damage indicator of a substructure is defined as the average reduction of the stiffness matrix of the initial undamaged substructure. The method is applied to simulated data of a six-storey, two-bay test frame (scale 1:5) that is to be tested at the Structural Laboratory of Aalborg University, Denmark. The simulations are performed using the non-linear finite element program SARCOF. Special emphasis is put on the investigation of the optimal location of measurement sensors, i.e. at which locations along the structure is the most information about the damage distribution gained. In all cases it is assumed that measurements are performed at top storey and ground surface, and the investigations are concentrated on putting one or two more measurement points in between. The two cases where the structure is excited in the first and second mode are investigated, and it is found that in general the sensors should be placed in the lower part of the structure. Furthermore, it is found that the method provides good results even when only the measurements at top storey and ground surface are used.     

Flow localization in fissure eruptions

 During a basaltic fissure eruption heat transfer from the hot magma to the surrounding rock causes a dramatic increase in the magmatic viscosity and solidification at the margins. Both viscosity contrast and solidification can amplify initial variations in the flow rate and lead to localization of the flow along the strike of the fissure. However, for typical parameters, amplification driven by solidification is slower and significantly weaker than amplification driven by viscosity variations. In fact, for the parameters examined, the amplification due to solidification is so weak that its effect is almost insignificant, whereas viscosity variation provides a strong active mechanism for flow localization. Laboratory experiments illustrate viscous localization and suggest that this mechanism is robust. The dependence of viscosity on temperature can cause a small change in the pressure of the magma chamber to lead to a large jump in the flow rate of magma through the fissure. Received: 13 March 1998 / Accepted: 27 September 1998     

A new approach to numerical simulation of source development of earthquake

ＡｎｅｗａｐｐｒｏａｃｈｔｏｎｕｍｅｒｉｃａｌｓｉｍｕｌａｔｉｏｎｏｆｓｏｕｒｃｅｄｅｖｅｌｏｐｍｅｎｔｏｆｅａｒｔｈｑｕａｋｅＣＨＵＮ－ＡＮＴＡＮＧ（唐春安）ＹＵ－ＦＡＮＧＦＵ（傅宇方）ＷＥＮＺＨＡＯ（赵文）ＣｅｎｔｅｒｆｏｒＲｏｃｋｂｕｒｓｔｓ...     

Seismic health monitoring of an instrumented multistory building using the interpolation method

In this paper, a new approach to structural damage localization is presented using as damage feature the interpolation error related to the use of a spline function in modeling the operational deformed shapes of the structure. Statistically significant variations of the interpolation error between the undamaged and the inspection phase indicate the onset of damage. A threshold value of the damage feature is defined in terms of the tolerable probability of false alarm to select variations of the interpolation error because of damage from those due to random sources. The method is successfully applied to a calibrated model of the factor building a real densely instrumented building at the University of California, Los Angeles. Results show that the method is effective for damage localization for both single and multiple locations of damage also in case of responses corrupted by noise. Copyright © 2014 John Wiley & Sons, Ltd.