Evaluation of predictors of non‐linear seismic demands using ‘fishbone’ models of SMRF buildings

Predictors (or estimates) of seismic structural demands that are less computationally time‐consuming than non‐linear dynamic analysis can be useful for structural performance assessment and for design. In this paper, we evaluate the bias and precision of predictors that make use of, at most, (i) elastic modal vibration properties of the given structure, (ii) the results of a non‐linear static pushover analysis of the structure, and (iii) elastic and inelastic single‐degree‐of‐freedom time‐history analyses for the specified ground motion record. The main predictor of interest is an extension of first‐mode elastic spectral acceleration that additionally takes into account both the second‐mode contribution to (elastic) structural response and the effects of inelasticity. This predictor is evaluated with respect to non‐linear dynamic analysis results for ‘fishbone’ models of steel moment‐resisting frame (SMRF) buildings. The relatively small number of degrees of freedom for each fishbone model allows us to consider several short‐to‐long period buildings and numerous near‐ and far‐field earthquake ground motions of interest in both Japan and the U.S. Before doing so, though, we verify that estimates of the bias and precision of the predictor obtained using fishbone models are effectively equivalent to those based on typical ‘full‐frame’ models of the same buildings. Copyright © 2003 John Wiley & Sons, Ltd.     

地震荷载作用下温度和围压对冻土强度影响的试验研究

通过对重塑冻结兰州黄土的动三轴试验，较系统研究了地震荷载作用下冻土的动强度特性，并且定量研究了其在不同温度(-2℃、-5℃、-7℃)和围压(1MPa、3MPa、5MPa)条件下的变化规律．结果发现：冻结黄土的动抗剪强度随围压的增大、温度的降低、振次的减少而增大；动粘聚力Cd随振次的减小和温度的降低而增大；动内摩擦角吼随振次的增大和温度的降低而增大。     

易门式大型铜矿床构造成矿动力学模型

针对金属矿床隐伏矿定位预测的关键问题,在提出构造成矿动力学的分支学术方向的基础上,以易门式大型铜矿床为例,从成矿地质背景、矿田构造、构造地球化学和成矿构造应力场等方面进行构造成矿动力学研究,阐述在构造应力场控制下成矿流体运移和聚集的规律。构造地球化学研究认为,构造地球化学异常反映矿体的原生晕;构造地球化学异常受构造控制,其分带特征可指示成矿流体的流向,并提供矿床成因和隐伏矿(化)体相对埋深的信息。构造应力场的控矿特征主要表现在:构造应力场导致控矿构造的形成,并驱动成矿流体的运移;构造应力场控制了成矿能量场;应力和能量的高值集中区分布特点可反映某些构造型式。在此基础上建立构造成矿动力学模型,概括隐伏矿成矿预测准则,据此提出若干重点找矿靶区和靶位,其中部分靶区得到工程验证,表明构造成矿动力学方法对隐伏矿定位预测和评价具有重要的指导意义。     

Simulation and measurement of surface shear stress over isolated and closely spaced transverse dunes in a wind tunnel

Topographic interactions generate multidirectional and unsteady air?ow that limits the application of velocity pro?le approaches for estimating sediment transport over dunes. Results are presented from a series of wind tunnel simulations using Irwin‐type surface‐mounted pressure sensors to measure shear stress variability directly at the surface over both isolated and closely spaced sharp‐crested model dunes. Findings complement existing theories on secondary air?ow effects on stoss transport dynamics and provide new information on the in?uence of lee‐side air?ow patterns on dune morphodynamics. For all speeds investigated, turbulent unsteadiness at the dune toe indicates a greater, more variable surface shear, despite a signi?cant drop in time‐averaged measurements of streamwise shear stress at this location. This effect is believed suf?cient to inhibit sediment deposition at the toe and may be responsible for documented intermittency in sand transport in the toe region. On the stoss slope, streamline compression and ?ow acceleration cause an increase in ?ow steadiness and shear stress to a maximum at the crest that is double that at the toe of the isolated dune and 60–70 per cent greater than at ?ow reattachment on the lower stoss of closely spaced dunes. Streamwise ?ow accelerations, rather than turbulence, have greater in?uence on stress generation on the stoss and this effect increases with stoss slope distance and with incident wind speed. Reversed ?ow within the separation cell generates signi?cant surface shear (30–40 per cent of maximum values) for both spacings. This supports ?eld studies that suggest reversed ?ow is competent enough to return sediment to the dune directly or in a de?ected direction. High variability in shear at reattachment indicates impact of a turbulent shear layer that, despite low values of time‐averaged streamwise stress in this region, would inhibit sediment accumulation. Downwind of reattachment, shear stress and ?ow steadiness increase within 6 h (h = dune height) of reattachment and approach upwind values by 25 h. A distance of at least 30 h is suggested for full boundary layer recovery, which is comparable to ?uvial estimates. The Irwin sensor used in this study provides a reliable means to measure skin friction force responsible for sand transport and its robust, simple, and cost‐effective design shows promise for validating these ?ndings in natural dune settings. Copyright © 2003 John Wiley & Sons, Ltd.     

基于GIS和SD方法的社会经济发展与生态环境响应动态模拟预测研究

在着重于空间现象分析处理的GIS与动态模拟的SD方法结合的模式下，动态模拟预测了不同社会经济发展策略对生态环境的影响，揭示了生态经济系统社会经济发展与生态环境相互影响关系，为区域可持续发展提供决策支持服务。     

虚拟加工环境中的工件动态建模方法研究

提出并实现了基于平面纹理映射的基元立方体构造方法，以之为动态结点建立了动态八叉树结构，实现了支持变精度动态建模的自相似递归算法。该算法确保离正在加工的部位更近的区域有更高的精度，并采用C^ Builder和OpenGL构造了一个集成于虚拟加工环境的可加工工件模型。     

基于GPS基准站网的GPS测量

采用基于GPS基准网的GPS测量可以提高GPS测量的可靠性和准确性 ,可以消除和减小GPS测量观测值中与时间和空间相关的大气误差和轨道误差的影响 ,使中、长距离快速静态定位和RTK动态定位成为现实 ,还具有可直接得到WGS84Z坐标等优点。本文介绍基于GPS基准站网的GPS测量 ,简要地论述GPS虚拟参考站法VRS和区域改正数法FKP的原理、方法和特点 ,以及目前实施中存在的一些问题     

磷脂脂肪酸在地下水微生物生态学中的应用及存在的若干问题

磷脂脂肪酸(PLFA)是研究地下水微生物生态的一种新兴技术，它比基于培养基的传统方法有许多明显的优势，但同时也存在一些需要解决的问题。样品中的PLFA总量可以通过转换因子估算地下水微生物的生物量，但微生物群落组成的差异和环境的物理变化都是潜在的误差来源，以传统微生物技术互补和选择合适的转换因子可提高结果的可靠性；PLFA还可以被用来指示地下水微生物在各种环境压力下的生理状态；用特定的PLFA生物标志物、PLFA的组成模式、指纹技术来描述地下水微生物的群落结构和变化特征时，存在的主要问题是不同微生物PLFA的重叠、背景值的干扰和环境因子变化的影响，以PLFA技术为主导，借助于数学统计方法，结合传统微生物技术、核酸鉴定、同位素示踪等多种技术可望有效地消除各种干扰因子，从而揭示完整的地下水微生物的生理生态，为地下水污染的生物修复提供理论指导。     

2-D deformation analysis of a half-space due to a long dip-slip fault at finite depth

Closed form analytical expressions of stresses and displacements at any field point due to a very long dip-slip fault of finite width buried in a homogeneous, isotropic elastic half-space, are presented. Airy stress function is used to derive the expressions of stresses and displacements which depend on the dip angle and depth of the upper edge of the fault. The effect of dip angle and depth of the upper edge of the fault on stresses and displacements is studied numerically and the results obtained are presented graphically. Contour maps for stresses and displacements are also presented. The results of Rani and Singh (1992b) and Freund and Barnett (1976) have been reproduced.