可液化场地微型桩地震响应特性研究

可液化场地微型桩的地震响应分析是确保工程安全和优化抗震设计的前提。应用动态离心机试验和三维有效应力数值分析方法,研究了微型单桩桩台的侧向变形和加速度、不同埋深桩身弯矩、可液化场地的加速度及超孔隙水压力等响应特征。首先开展了相对密实度为57%饱和土层、输入波是频率为1 Hz和峰值加速度为1.516 m/s2正弦波的微型桩40 g动态地震响应离心机试验,进而应用基于多重剪切机构塑性模型和液化前缘状态面概念的三维有效应力分析方法,反演了试验结果,并进行了对比分析,结果表明,数值模拟与离心机试验结果吻合,液化场地特性控制着建于其中微型桩的地震响应特征,微型桩桩台的水平变形和残余变形可达78、30 mm,桩身最大弯矩和最大残余弯矩呈现向桩身底部迁移特点,同时表明,基于动态土工离心机试验和数值分析相结合的研究方法,分析可液化场地微型桩地震响应特性是有效可行的,研究结论为可液化场地微型桩的抗震设计提供了可靠的依据和参考。     

多年冻土斜坡路基失稳变形影响因素及特征研究

从力学相似性的角度进行多年冻土斜坡路基失稳变形离心模型试验,分析最大融深状态下冻土斜坡路基土层性质、高度以及地基坡度对其稳定性的影响规律,研究冻土斜坡路基失稳变形特性、失稳机制及模式,将片石路基与普通路基进行对比分析。试验结果表明,冻土斜坡路基土层力学性质、路基高度和地基坡度对其稳定具有显著影响,路基的变形在冻融交界面发生骤变,变形主要集中在冻融交界面之上的土层;在本试验条件下,多年冻土斜坡路基合理高度约为5 m;当斜坡路基高度为5 m时,地基坡度大于1: 6,路基横向变形迅速增大;冻土斜坡路基的沉降和横向变形表现出较大的不均匀性,冻土斜坡路基变形失稳的根本原因是冻融交界附近软弱带的抗剪强度不足,阳坡冻融交界面之上的土层沿软弱带滑移破坏;路基破坏可分为浅层开裂破坏、深层开裂破坏和整体滑移破坏3种;冻土斜坡片石路基的水平位移和沉降明显小于普通路基,片石路基具有较好的整体稳定性。     

水平荷载作用下风电机桩基础的离心模型试验研究

桩基础是近海风机经常采用的基础形式。由于风电机组对基础的承载力和变形有着严格的要求,而水平荷载常常是控制荷载,因此,研究水平荷载作用下风机桩基础的应力、变形特性具有重要意义。针对风机单桩基础,选取典型的黏土地基,进行了水平加载条件下的离心模型试验,重点分析了桩身的响应及桩周围土体的变形特点。试验结果表明,在水平荷载作用下,桩顶的水平位移随着水平力的增加而增加,位移的增加速率在临界荷载之后增长较快;桩身弯矩分别在埋深1/5和3/5处附近分别出现极大值和极小值,且桩底具有一定弯矩值;桩周围土体的变形随着离桩距离的增加而减小,可分为主动区和被动区。桩对土体变形的影响区域随着水平力的增加而不断扩展,最后基本稳定在2倍桩径范围内。     

Determination of In Situ Sediment Shear Strength from Advanced Piston Corer Pullout Forces

Abstract

The advanced piston cover (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.     

Uplift mechanism for a shallow-buried structure in liquefiable sand subjected to seismic load: centrifuge model test and DEM modeling

Based on a centrifuge model test and distinct element method(DEM), this study provides new insights into the uplift response of a shallow-buried structure and the liquefaction mechanism for saturated sand around the structure under seismic action. In the centrifuge test, a high-speed microscopic camera was installed in the structure model, by which the movements of particles around the structure were monitored. Then, a two-dimensional digital image processing technology was used to analyze the microstructure of saturated sand during the shaking event. Herein, a numerical simulation of the centrifuge experiment was conducted using a two-phase(solid and fl uid) fully coupled distinct element code. This code incorporates a particle-fl uid coupling model by means of a "fi xed coarse-grid" fl uid scheme in PFC3D(Particle Flow Code in Three Dimensions), with the modeling parameters partially calibrated based on earlier studies. The physical and numerical models both indicate the uplifts of the shallow-buried structure and the sharp rise in excess pore pressure. The corresponding micro-scale responses and explanations are provided. Overall, the uplift response of an underground structure and the occurrence of liquefaction in saturated sand are predicted successfully by DEM modeling. However, the dynamic responses during the shaking cannot be modeled accurately due to the restricted computer power.     

Centrifuge modeling of single pile response due to lateral cyclic loading in kaolin clay

In offshore engineering, pile foundations are commonly constructed in marine deposits to support various structures such as offshore platforms. These piles are subjected to lateral cyclic loading due to wind, wave action, and drag load from ships. In this paper, centrifuge model tests are conducted to investigate the response of the existing single piles due to lateral cyclic loading. The cyclic loading was simulated by a hydraulic actuator. It is found that the residual lateral movement and bending strain are induced in the existing pile after each loading–unloading cycle. This is because plastic deformation is induced in the soil surrounding the existing pile during each loading–unloading cycle. By increasing the applied loads during cyclic loading–unloading process, the lateral movements and bending strains induced in the pile head increase simultaneously. As the cyclic loading varies from 10 to 50 kN, the residual pile head movement increases from 40 to 154?mm, and the residual bending strain of the existing pile varies from 100 to 260 με. The ratio of residual to the maximum pile head movements varies from 0.17 to 0.22, while the ratio of residual to the maximum bending strains is in a range of 0.12–0.55.     

氯离子在黏土-膨润土屏障中迁移的离心试验研究

将对流-扩散试验装置置于土工离心机中,以50g离心加速度运行12 h,研究了黏土-膨润土混合土样中Cl-的迁移扩散,使用解析解对试验结果进行拟合确定相关参数,分析了试验的相似条件,使用商用软件对离心试验原型进行模拟,与试验结果进行比较,探讨了离心机用于溶质迁移分析的比尺效应,最后通过数值分析研究了试验的黏土-膨润土屏障用于老垃圾填埋场防渗帷幕补强的效果。结果表明,土工离心机试验中,按实际出流量计算的实际孔隙水流速小于临界流速,两试样中的佩克莱数（Pe数）小于临界Pe数,机械弥散的作用可以忽略,试验满足扩散的相似定律;离心机试验所模拟的2.5 m厚衬垫原型,在水头5 m和10 m作用下3.42 a后均未被击穿;常重力下试验土样的渗透系数为8.5×10-8 cm/s,有效扩散系数为7.82×10-7 cm2/s,对试验原型进行的数值模拟表明,n倍重力加速度下,土工离心机可以 尺寸的试样实现对原型的模拟,同时将对流和扩散作用下的溶质迁移时间缩短至原型的 ;试验的黏土-膨润土屏障用于老垃圾填埋场防渗补强,可显著减缓溶质迁移,防渗补强后可满足渗滤液迁移扩散的控制要求。     

Centrifuge modelling of lateral loading behaviour of a “semi-rigid” Mono-pile in soft clay

Abstract

Mono-pile foundations have been widely used for offshore wind turbines principally due to their convenient construction and cost-effective nature. So far, little attention has been paid to large diameter “semi-rigid” piles that have distinct behaviours from flexible or ideally rigid piles. This paper presents a series of centrifuge model tests to study the deforming and bearing characteristics of a 5.9 dia. semi-rigid pile under lateral loadings in kaolin clay. For monotonic loading, a modified p–y curve analysis model considering rotational soil flow near the rotation centre of pile was proposed, highlighting the limitation of classic plane-strain based plasticity models to evaluate the ultimate lateral pile-soil resistance. For cyclic loading, a strong correlation between the degree of soil degradation and cyclic load amplitude was identified. Besides, a degradation factor model, accounting for various cyclic stress levels and soil depths, was proposed, which can be used to assess the accumulative displacement of semi-rigid piles under cyclic loadings in soft clay.     

刚/柔性组合墙面加筋土挡墙内部破坏机制

基于离心模型试验成果,建立软土地基刚/柔性组合墙面加筋土挡墙离散-连续耦合数值模型,采用离散单元颗粒流程序PFC和有限差分程序FLAC分别模拟加筋土挡墙和软土地基,分析挡墙的变形、筋材拉力分布及内部破坏演化过程,并与刚性地基上挡墙情况进行比较,以探讨刚/柔性组合墙面加筋土挡墙的内部破坏机制。研究结果表明,数值模型计算结果与离心模型试验结果吻合,其内部潜在破坏面经过连接件锚固端位置,各层筋材拉力均在连接件锚固端位置最大;软土地基上挡墙和刚性地基上挡墙的内部破坏面均一致,且筋材均由下而上依次断裂;软土地基上挡墙内部破坏面与地基圆弧滑移面贯通,为复合滑动模式,而刚性地基上挡墙整体破坏模式为折线型,连接件埋深范围内加筋体沿其底部连接件水平滑出。     

Use of a single-bowl continuous-flow centrifuge for dewatering suspended sediments: Effect on sediment physical and chemical characteristics

The use of a single-bowl continuous-flow centrifuge (CFC, Sharples-Pennwalt Model AS-12) for dewatering suspended sediment from large volumes of river water is evaluated. Sediment-recovery efficiency of 86-91 per cent is comparable to that of other types of CFC units. The recovery efficiency is limited by the particle-size distribution of the feed water and by the limiting particle diameter that is retained in the centrifuge bowl. The limiting particle diameter, using the parameters for this study (bowl radius = 10.5cm; bowl length = 71.1 cm; rotational velocity = 16000 r min^?1; flow rate = 2 L min^?1, and an assumed hydrated particle density = 1.7 gm cm^?3), is 370 nm. There seems to be no particle-size fractionation within the centrifuge bowl—the median particle size was the same at the top as at the bottom. Particle electrophoretic mobility plays some role in fractionation of particles within the centrifuge. The mobility ranged from ?1.19 to ?2.01 × 10^?8 m² V^?1 s^?1, which is typical of clays coated with organic matter, the charge of which is partially neutralized by divalent cations and iron. Contamination by trace metals and organics is minimized by coating all surfaces that come in contact with the sample with either FEP or PFA Teflon and using a removable FEP Teflon liner in the centrifuge bowl. Because of the physical and chemical factors affecting particle fractionation within the centrifuge, care must be exercised in interpreting the environmental consequences of particles collected by continuous-flow centrifugation.