有机质在中国东北部森林沼泽区化探异常追踪和查证中的应用

在东北森林沼泽区的几个矿区(点)上,通过以泥炭、腐殖层土壤为采样介质的区域化探异常追踪查证方法技术试验研究,发现Au、Ag、Cu、Pb、Zn等主要成矿元素的测量结果与水系碎屑沉积物、残坡积物的基本一致,对矿体均有良好的反映.研究结果表明在这类景观区化探找矿工作中有机质是可以利用的.     

The sandstone-hosted stratiform copper mineralization at Mwitapile and its relation to the mineralization at Lufukwe, Lufilian foreland, Democratic Republic of Congo

The Lufilian foreland is a triangular-shaped area located in the SE of the Democratic Republic of Congo and to the NE of the Lufilian arc, which hosts the well-known Central African Copperbelt. The Lufilian foreland recently became an interesting area with several vein-type (e.g., Dikulushi) and stratiform (e.g., Lufukwe and Mwitapile) copper occurrences. The Lufilian foreland stratiform Cu mineralization is, to date, observed in sandstone rock units belonging to the Nguba and Kundelungu Groups (Katanga Supergroup).The Mwitapile sandstone-hosted stratiform Cu prospect is located in the north eastern part of the Lufilian foreland. The host rock for the Cu mineralization is the Sonta Sandstone of the Ngule Subgroup (Kundelungu Group). A combined remote sensing, petrographic and fluid inclusion microthermometric analysis was performed at Mwitapile and compared with similar analysis previously carried out at Lufukwe to present a metallogenic model for the Mwitapile- and Lufukwe-type stratiform copper deposits. Interpretation of ETM+ satellite images for the Mwitapile prospect and the surrounding areas indicate the absence of NE–SW or ENE–WSW faults, similar to those observed controlling the mineralization at Lufukwe. Faults with these orientations are, however, present to the NW, W, SW and E of the Mwitapile prospect. At Mwitapile, the Sonta Sandstone host rock is intensely compacted, arkosic to calcareous with high silica cementation (first generation of authigenic quartz overgrowths). In the Sonta Sandstone, feldspar and calcite are present in disseminated, banded and nodular forms. Intense dissolution of these minerals caused the presence of disseminated rectangular, pipe-like and nodular dissolution cavities. Sulfide mineralization is mainly concentrated in these cavities. The hypogene sulfide minerals consist of two generations of pyrite, chalcopyrite, bornite and chalcocite, separated by a second generation of authigenic quartz overgrowth. The hypogene sulfide minerals are replaced by supergene digenite and covellite. Fluid inclusion microthermometry on the first authigenic quartz phase indicates silica precipitation from an H₂O–NaCl–CaCl₂ fluid with a minimum temperature between 111 and 182 °C and a salinity between 22.0 and 25.5 wt.% CaCl₂ equiv. Microthermometry on the second authigenic quartz overgrowths and in secondary trails related to the mineralization indicate that the mineralizing fluid is characterized by variable temperatures (Th = 120 to 280 °C) and salinities (2.4 to 19.8 wt.% NaCl equiv.) and by a general trend of increasing temperatures with increasing salinities.Comparison between Mwitapile and Lufukwe indicates that the stratiform Cu mineralization in the two deposits is controlled by similar sedimentary, diagenetic and structural factors and likely formed from a similar mineralizing fluid. A post-orogenic timing is proposed for the mineralization in both deposits. The main mineralization controlling factors are grain size, clay and pyrobitumen content, the amount and degree of feldspar and/or calcite dissolution and the presence of NE–SW to ENE–WSW faults. The data support a post-orogenic fluid-mixing model for the Mwitapile- and Lufukwe-type sandstone-hosted stratiform Cu deposits, in which the mineralization is related to the mixing between a Cu-rich hydrothermal fluid, with a temperature up to 280 °C and a maximum salinity of 19.8 wt.% NaCl equiv., with a colder low salinity reducing fluid present in the sandstone host rock. The mineralizing fluid likely migrated upwards to the sandstone source rocks along NE–SW to ENE–WSW orientated faults. At Lufukwe, the highest copper grades at surface outcrops and boreholes were found along and near to these faults. At Mwitapile, where such faults are 2 to 3 km away, the Cu grades are much lower than at Lufukwe. Copper precipitation was possibly promoted by reduction from pre-existing hydrocarbons and non-copper sulfides and by the decrease in fluid salinity and temperature during mixing. Based on this research, new Cu prospects were proposed at Lufukwe and Mwitapile and a set of recommendations for further Cu exploration in the Lufilian foreland is presented.     

无外加流体、350℃和差异应力条件下硫化物再活化实验研究

红透山块状硫化物矿石主要成分为黄铁矿、磁黄铁矿、黄铜矿、闪锌矿和石英、角闪石、黑云母等脉石矿物。将此矿石烘干后作为试料置于岩石三轴应力试验机,在13h内将轴压、围压和温度分步升至1276MPa、414MPa和350℃,然后在空气中自然冷却至室温。实验产物中黄铁矿、石英、长石等以脆性碎裂为主,而磁黄铁矿、黄铜矿、闪锌矿和云母等以塑性变形为主。再活化的黄铜矿、磁黄铁矿和少量闪锌矿呈脉和网脉穿插黄铁矿碎斑。实验结果表明,即使没有外来流体加入．构造动力作用所导致的流体包裹体破坏所释出的流体,就足以使成矿物质发生活化转移和再活化。     

河南洛宁段河金矿流体包裹体研究和矿床成因

河南省洛宁县段河石英脉型金矿主要包括石寨沟和岭东两个矿区,分别由3～4条含金石英脉构成。矿化过程从早到晚包括石英-黄铁矿、石英-多金属硫化物和石英-碳酸盐等3个阶段．其中中阶段金矿化最强,次为早阶段。各阶段石英中流体包裹体以气液两相包裹体为主．次为纯液体包裹体。激光拉曼测试表明,气液两相包裹体的液相为H2O,气相主要为Ho和CO2混合、纯H2O,次为纯CO2;纯液体包裹体为纯H2O。石寨沟矿区包裹体均一温度从早到晚依次为240．9～315．9℃．188．7～304．5℃,137．3～259．3℃：流体盐度变化依次为（6．74～12．85）wt%NaCl．eq,（2．41～8．68）wt％NaCl．eq,（2．24-7．86）wt%NaCl．eq。岭东矿区均一温度从早到晚依次为303．7-343．1℃,251．8-325．4℃,305．7～355．0℃：流体盐度变化依次为（5．11～11．70）wt％NaCl．eq,（2．74-10．11）wt％NaCl．eq,（0．53-6．74）wt％NaCl．eq。两矿区主成矿期流体均为中温、低盐度,早阶段流体为改造热液和变质热液的混合体,含一定量CO2,且流体CO2含量和盐度从早到晚逐渐降低。石寨沟矿区包裹体均一温度逐渐降低,而岭东矿区包裹体均一温度先降后升,加之岭东矿区各阶段成矿温度均高于石寨沟矿区．表明成矿流体系统主要受岩浆热驱动,岭东矿区更靠近岩体,且在晚阶段又有脉动性的岩浆加热．段河金矿区南部存在隐伏岩体。     

延长探区下古生界马家沟组储层流体包裹体特征

流体包裹体研究在划分油气运移充注期次、确定油气藏形成时间等方面均有重要的应用价值.通过镜下观察流体包裹体的特征,划分类型,描述其特征,对与烃类共生的盐水包裹体进行均一化温度测试,并结合其他相关地质资料,认为延长探区马家沟组储层流体包裹体的均一温度集中分布在85~115℃范围内,包裹体捕获时的埋藏深度为2500~2800 m.结合盆地的埋藏史推测天然气成藏时间为晚三叠-早侏罗世.     

高砷地下水研究的热点及发展趋势

全球范围内广泛分布的高砷地下水给人们的健康造成了极大的威胁.高砷地下水的形成机理是一项世界性的科学问题.介绍了高砷地下水的分布特点、富集机理,阐明了溶解性有机物、地下水流动特征对高砷地下水形成的影响机制.现今的研究揭示了有机物和微生物协同作用下高砷地下水的形成过程,并且在高砷地下水的空间分布、时间变化特征以及人类活动对高砷地下水形成的影响等方面取得了一些创新性成果.这3方面的研究也逐渐成为近些年高砷地下水研究的热点.这些研究不仅丰富了砷迁移转化的理论成果,而且有助于开辟低砷水源,保障水资源的可持续利用,具有重要的理论和现实意义.     

Determining Pressure with Daughter Minerals in Fluid Inclusion by Raman Spectroscopy: Sphalerite as an Example

Abstract: Raman frequency of some materials, including minerals, molecules and ions, shifts systematically with changing pressure and temperature. This property is often used as a pressure gauge in high pressure experiments with the hydrothermal diamond anvil cell (HDAC). Since the system of fluid inclusion is similar to that of HDAC, it can also be used to determine the internal pressure of fluid inclusions. Sphalerite is a common daughter mineral. In this study, the frequency shift of the 350 cm?1 peak of sphalerite has been studied from 296 to 523 K and from 0.07 to 2.00 GPa using the HDAC. The global slope of the isotherms (?n350/?p)T is 0.0048 in the studied pressure range. No significant variation of the slopes with temperature has been observed. The correlation between the frequency shift of the 350 cm?1 peak of sphalerite and pressure and temperature is constrained as P=208.33(?np)350+3.13T?943.75. This relationship may be used to estimate the internal pressure of the sphalerite-bearing fluid inclusions.     

大庆长垣以西地区扶余油层次生孔隙预测

为了在普遍低孔、低渗的背景下寻找次生孔隙发育的储层,在次生孔隙形成机制分析和储层成岩作用研究的基础上,结合考虑影响次生孔隙形成的多种因素,对大庆长垣以西地区扶余油层次生孔隙发育区进行预测。研究表明,该地区次生孔隙的形成主要受青山口组下排有机酸和碳酸的影响,且受到断层的控制和超压的影响,次生孔隙主要分布在齐家地区和龙虎泡阶地等凹陷周边区域,在西部斜坡区亦发育由大气水淋滤所形成的次生孔隙。在次生孔隙发育区,若发育岩性圈闭或构造圈闭,则为有利的油气聚集场所。      

荧光分析法在油气化探中的应用

荧光光谱法是分析芳烃的灵敏、快速、高效的方法,通过样品的同步荧光光谱和三维荧光光谱特征,可以进行油气属性的判断;区别油气信息和煤信息,区分油气信息和泥浆污染信息,提高钻井预测的准确度.某些情况下,可以用简单、便捷的同步荧光光谱取代三维荧光光谱分析,达到事半功倍的效果.     

山东金青顶金矿床和七宝山金矿床的流体包裹体REE组成

文章运用电感耦合等离子体质谱（ICP-MS）方法，研究了金青顶金矿床和七宝山金矿床的脉石英中流体包裹体REE组成特征，结果表明流体包裹体的REE均为LREE富集型，并显示Eu正异常。成矿流体REE配分模式和REE参数特征表明它们具有相当的来源。与金矿有关的成矿母岩，即昆嵛山花岗岩和七宝山次火山岩的REE特征也极为相似，反映成矿流体的REE组成都有从成岩向成矿过程演化继承的关系。矿床流体包裹体REE组成的相似特征及矿床碳氧同位素等特点表明，金青顶金矿床和七宝山金矿床是华北东部中生代同一构造热事件的产物。