基于最大球算法定量表征土体空间孔隙网络

孔隙网络控制着土体渗流、排水固结与基质吸力等重要工程性质。本文介绍了多孔介质孔隙网络最大球建模基本原理与算法。以显微CT扫描振捣干法生成的南京粉砂试样为例,采用最大球算法建立了试样三维重构模型表征单元体(REV)的空间孔隙网络球棍模型,计算得到了样品REV尺度的孔隙网络参数,统计发现,孔隙半径、喉道半径、孔隙配位数、孔隙截面形状因子、喉道截面形状因子与喉道长度等孔隙参数均近似服从正态分布,孔隙体积近似服从衰减型指数分布。孔隙与喉道半径分别分布在100μm与65μm以内,两者数学期望分别为40. 0μm与18. 0μm;配位数分布在25以内,数学期望为5. 1;孔隙与喉道截面形状因子分别分布在0. 01~0. 04与0. 01~0. 05的区间内,两者数学期望分别为0. 019与0. 033;喉道长度分布在100~800μm以内,数学期望为292. 22μm。同时发现,样品中体积小于1. 5×10^7μm^3的小孔隙数量超过90%。本方法可应用于土体细观孔隙结构的定量表征。     

三峡库区龙门寨危岩体崩塌产生涌浪研究

长江两岸高耸的危岩体对航道、沿岸居民带来巨大安全隐患。大宁河属于长江一级支流,龙门寨危岩体位于大宁河上,距离巫山县城仅1 km。利用FLOW-3D软件,模拟了145 m、175 m两种水位工况下龙门寨危岩体崩塌产生涌浪过程和涌浪传播过程。模拟结果表明,涌浪在145 m水位工况下最大浪高约为17.9 m,175 m水位工况下最大浪高约为11.6 m;在巫山县的五个码头处,两种水位工况最大涌浪爬高分别约为10.9 m、3.8 m;根据涌浪高度,对大宁河进行危险分区,145 m水位工况下极高危险区长度约4.4 km,很高危险区长度约1.9 km;175 m水位工况下极高危险区长度约3.0 km,很高危险区长度约1.0 km。研究结果有助于防控龙门寨危岩体潜在涌浪灾害危害,保障大宁河航道和巫山县码头安全,同时也为三峡库区滑坡涌浪灾害提供了预警依据。      

Middle Permian organic carbon isotope stratigraphy and the origin of the Kamura Event

Large carbon cycle perturbations associated with the Middle Permian (Capitanian) mass extinction have been widely reported, but their causes and timing are still in dispute. Low resolution carbon isotope records prior to this event also limit the construction of a Middle Permian chemostratigraphic framework and global or local stratigraphic correlation, and hence limit our understanding of carbon cycle and environmental changes. To investigate these issues, we analyzed the ¹³C_org values from the Middle Permian chert-mudstone sequence (Gufeng Formation) in the Lower Yangtze deep-water basin (South China) and compared them with published records to build a chemostratigraphic scheme and discuss the underlying environmental events. The records show increased δ¹³C_org values from late Kungurian to early Guadalupian, followed by a decrease to the late Wordian/early Capitanian. The early-mid Capitanian was characterized by elevated δ¹³C_org values suggesting the presence of the “Kamura Event”: an interval of heavy positive values seen in the δ¹³C_carb record. We propose that these heavy Capitanian δ¹³C values may be a response to a marked decline in chemical weathering rates on Pangea and associated reduction in carbonate burial, which we show using a biogeochemical model. The subsequent negative δ¹³C excursion seen in some carbonate records, especially in shallower-water sections (and in a muted expression in organic carbon) coincide with the Capitanian mass extinction may be caused by the input of isotopically-light carbon sourced from the terrestrial decomposition of organic matter.     

Development and Re‐Evaluation of Tourmaline Reference Materials for In Situ Measurement of Boron δ Values by Secondary Ion Mass Spectrometry

Six tourmaline samples were investigated as potential reference materials (RMs) for boron isotope measurement by secondary ion mass spectrometry (SIMS). The tourmaline samples are chemically homogeneous and cover a compositional range of tourmaline supergroup minerals (primarily Fe, Mg and Li end‐members). Additionally, they have homogeneous boron delta values with intermediate precision values during SIMS analyses of less than 0.6‰ (2s). These samples were compared with four established tourmaline RMs, that is, schorl IAEA‐B‐4 and three Harvard tourmalines (schorl HS#112566, dravite HS#108796 and elbaite HS#98144). They were re‐evaluated for their major element and boron delta values using the same measurement procedure as the new tourmaline samples investigated. A discrepancy of about 1.5‰ in δ¹¹B was found between the previously published reference values for established RMs and the values determined in this study. Significant instrumental mass fractionation (IMF) of up to 8‰ in δ¹¹B was observed for schorl–dravite–elbaite solid solutions during SIMS analysis. Using the new reference values determined in this study, the IMF of the ten tourmaline samples can be modelled by a linear combination of the chemical parameters FeO + MnO, SiO₂ and F. The new tourmaline RMs, together with the four established RMs, extend the boron isotope analysis of tourmaline towards the Mg‐ and Al‐rich compositional range. Consequently, the in situ boron isotope ratio of many natural tourmalines can now be determined with an uncertainty of less than 0.8‰ (2s).     

Copper Isotopic Analysis in Geological and Biological Reference Materials by MC‐ICP‐MS

The characterisation of relative copper isotope amount ratios (δ⁶⁵Cu) helps constrain a variety of geochemical processes occurring in the geosphere, biosphere and hydrosphere. The accurate and precise determination of δ⁶⁵Cu in matrix reference materials is crucial in the effort to validate measurement methods. With the goal of expanding the number and variety of available geological and biological materials, we have characterised the δ⁶⁵Cu values of ten reference materials by MC‐ICP‐MS using C‐SSBIN model for mass bias correction. SGR‐1b (Green River shale), DOLT‐5 (dogfish liver), DORM‐4 (fish protein), TORT‐3 (lobster hepatopancreas), MESS‐4 (marine sediment) and PACS‐3 (marine sediment) have for the first time been characterised for δ⁶⁵Cu. Additionally, four reference materials (with published δ⁶⁵Cu values) have been characterised: BHVO‐1 (Hawaiian basalt), BIR‐1 (Icelandic basalt), W‐2a (diabase) and Seronorm? Trace Elements Serum L‐1 (human serum). The reference materials measured in this study possess complex and varied matrices with copper mass fractions ranging from 1.2 µg g^?1 to 497 µg g^?1 and δ⁶⁵Cu values ranging from ?0.20‰ to 0.52‰ with a mean expanded uncertainty of ± 0.07‰ (U, k = 2), covering much of the natural copper isotope variability observed in the environment.     

High‐Precision,High‐Accuracy Oxygen Isotope Measurements of Zircon Reference Materials with the SHRIMP‐SI

Analytical protocols for SHRIMP‐SI oxygen isotope analysis (δ¹⁸O) of a suite of zircon reference materials (RMs) are presented. Data reduction involved a robust estimate of uncertainties associated with the individual spot as well as for groups where the spot data are combined. The repeatability of δ¹⁸O measurements is dependent on both the analytical conditions and the choice of the primary reference material. Under optimised conditions, repeatability was often better than 0.4‰ (2s) allowing sample uncertainties to be obtained to better than 0.2‰ (at 95% confidence limit). Single spot uncertainty combined the within‐spot precision with the scatter associated with repeated measurements of the primary zircon reference material during a measurement session. The uncertainty for individual spots measured under optimised conditions was between 0.3 and 0.4‰ (at 95% confidence). The analytical protocols described were used to assess a variety of zircon RMs that have been used for geochronology and for which laser fluorination oxygen isotope data are available (Temora 2, FC1, R33, QGNG and Ple?ovice), as well as zircons that have been used as RMs for trace element or other types of determination (Mud Tank, Monastery, 91500, AS57, AS3, KIM‐5, OG1, SL13, CZ3 and several other Sri Lankan zircons). Repeated analyses over nine sessions and seven different mounts show agreement within analytical uncertainty for Temora 2, FC1, R33, QGNG, Ple?ovice and 91500, when normalised to Mud Tank. For existing ion microprobe mounts with these materials, an appropriate δ¹⁸O can be determined. However, care should be taken when using zircons from the Duluth Complex (i.e., FC1, AS57 and AS3) as reference materials as our data indicated an excess scatter on δ¹⁸O values associated with low‐U zircon grains.     

Carbonate slope re-sedimentation in a tectonically-active setting (Western Sicily Cretaceous Escarpment,Italy)

Tectonic processes are widely considered as a mechanism causing carbonate platform margin instabilities leading to the emplacement of mass transport deposits and calciturbidites. However, only few examples establishing a clear link between tectonics and re-sedimentation processes are known from the literature. The two-dimensional and three-dimensional wire-cut walls of hundreds of quarries extracting ornamental limestones (for example, Perlato di Sicilia) from the Western Sicily Cretaceous Escarpment in Italy expose a series of mass transport deposits. The depositional architecture, spatial facies distribution and sedimentary features of these deposits were studied in detail. Thin section analysis was used to define the microfacies characteristics and to determine the age of the re-sedimented limestones. Eleven facies types grouped into four facies associations were recognized that defined specific depositional processes and environments. The stratigraphic architecture of the slope was reconstructed using four composite facies successions based on the detailed analysis and correlation of the field sections. The palaeoslope orientation was reconstructed based on the analysis of synsedimentary faults, slump scars and pinch-out geometries. The Western Sicily Cretaceous Escarpment was strongly influenced by synsedimentary transtensional tectonics in combination with magmatic processes, as suggested by the presence of tuffites and pillow lava intercalations within the re-sedimented carbonate series. These volcanics point to a major role of crustal shear as a trigger for mass transport deposit emplacement. The facies distribution along the Western Sicily Cretaceous Escarpment delivers new insights into the deformation processes accompanying the crustal extension of the Cretaceous western Tethys realm.     

文丘里法在河流流量推算中的应用

流量测验常见方法有常规水文缆道流速仪法、超声波时差法、声学多普勒流速(ADCP)、雷达波流速等,上述方法各有优缺点,适用于不同场合。文丘里现象被广泛用来测量封闭管道中单相稳定流体的流量,依据伯努利定律可知流速的增大伴随流体压力的降低,即受限流动在通过缩小的过流断面时流体出现流速增大的文丘里效应,根据该效应,可通过河段文氏等效,获得估算的天然河流水体流量。经实例验证,该方法计算精度较高,达到流量测验规范要求,可作为流量估算的一种辅助手段。     

Dynamic analysis on structures base-isolated by a ball system with restoring property

A computational model with its analysis method for base-isolated structures by a ball system with restoring property under seismic force is proposed in this paper, and the programs using numerical integration method and incremental harmonic balance method are developed. The analysis method is verified by shaking table test results of a three-storey masonry model. With these programs, the effect of some factors on the aseismic behaviour of base isolation system are analysed, and the comparison of seismic response between structures with and without base isolation is made. Results of both theory and test show that the above-mentioned base isolation system has apparent advantages over the traditional aseismic structures. © 1998 John Wiley & Sons, Ltd.