挑坎体型对下游雾化影响的试验研究

以解决挑流消能工在泄洪期间为提高消能率而加重下游雾化问题为目标,探究不同体型挑坎的下游雾化特性。通过水力学模型试验,对典型的非对称舌型坎、标准舌型坎、扭面贴坎和连续坎的下游水舌风分布、下游溅水雨强和不同液滴体积分布以及挑流水舌水力特性与冲刷特性进行了研究。研究表明:①各种工况下,非对称舌型坎、标准舌型坎、扭面贴坎的下游水舌风风速均大于连续坎。②对于非对称舌型坎,其溢洪道轴线左侧溅水强度大于右侧,其雨强左右两侧峰值差值最大为5.625 g/(m 2·min);对于扭面贴坎,其溢洪道轴线右侧溅水强度更大,其雨强左右两侧峰值差值最大为45.125 g/(m 2·min)。③随着距离水舌入水点长度增大,大粒径水滴数量和体积占比均剧烈下降;连续坎和舌型坎的挑宽均随着角度的增加而增加;冲坑深度随着角度的减小而增大。④在挑坎合适边墙侧设置扭面贴角能改善下游雾化危害,同时适当增加挑角可以减弱下游冲刷破坏。     

西南某岩溶区地下水系统示踪试验与解析

以西南某典型岩溶区为例,解析示踪试验在岩溶管道连通性以及获取水文地质参数中的应用。选择落水洞为投放点,分别从落水洞西侧和东侧寻找地下水出露点作为接收点,判别落水洞地下径流的实际去向以及落水洞与接收点之间的水力联系。结合Qtracer2软件对示踪试验成果进行定量解析,确定示踪剂回收率、地下水平均流速、最快流速,估算出岩溶管道结构特征和水文地质参数。结果表明:落水洞与接收点JS01、JS03之间不存在直接水力联系;落水洞与接收点JS02存在水力联系且岩溶管道极为发育,含水介质不均匀,地下水运移路径较为通畅,为典型的紊流流态;落水洞地下径流的主要方向是由西向东,但在丰水期雨量较大期间,接收点JS04能够接收到荧光素钠,说明丰水期水位上涨后两者间会有水力联系,导致部分水量向落水洞西侧排泄。     

高烈度区双洞隧道洞口段地震响应分析与振动台模型试验

强震作用下,隧道地下结构损伤严重,其中洞口段更是抗震的薄弱环节,但其影响规律和特点目前尚缺乏系统的计算分析和研究。以强震区扯羊隧道为例,首先采用FLAC3D对双洞隧道洞口段地震响应进行分析,再用模型试验的方法进行洞口段模型试验,测量其地震响应应变规律,观测其震害发展情况,并与数值分析结果相互验证。结果表明:地震作用下,隧道仰拱横向位移较大;随着隧道埋深增加,内力逐步增加,其中墙角部位内力较大;洞口处隧道围岩在强震作用下会产生贯通性裂缝,影响隧道洞口稳定;地震作用下的明洞与暗洞交接处内力较大;地震作用下的双洞隧道之间存在较强的动力相互作用。     

基于新型单相MICP技术改性黏性土力学特性的试验研究

微生物诱导碳酸钙沉积(MICP)是一种绿色低碳的新型土体改性技术.该技术当前主要适用于渗透性较好的砂土,普遍使用两相处理方法,即菌液和胶结液分开施用.然而,对于渗透性相对较差的黏性土,传统的两相处理方法难以适用.为此,引入新的单相胶结方法,即菌液和胶结液混合施用,通过调节溶液的初始pH值为细菌水解作用提供窗口期,避免微生物絮凝阻塞孔隙,使混合液均匀分布于土体一定深度范围内,从而达到显著提升胶结效果的目的.利用喷洒法将混合液喷洒至土体表层进行MICP处理,处理完成后使用超微型贯入仪SMP-1测试土体表层不同深度处的结构强度,分析土体力学特性的空间差异,对土体的胶结效果进行定量评价.此外,探究了胶结液浓度(0.2M、0.5M和1.0M)及胶结方法(调节pH与否)对于土体结构强度及MICP改性效果的影响.结果表明:采用单相MICP技术对黏性土进行改性,能够显著提高其结构强度,具有较好的适用性;在不高于1.0 M的胶结液浓度范围内,黏性土的胶结效果随着胶结液浓度增加而提升;相比较而言,调节pH的单相胶结方法对于提升土体胶结的深度和均匀性有明显积极作用.新型单相MICP技术简单易行,能够节约成本,在黏性土表层加固方面具有潜在推广应用价值.     

某地下空间承压含水层抽水试验及成果分析

由于地下水突涌风险,地下空间在施工作业中有必要通过抽水试验确定承压含水层的水文地质参数。依据勘察报告的初步评价,基坑开挖15.5m时,场地内第⑦1层承压含水层有可能产生突涌,为确保工程安全施工,需开挖前进行承压含水层抽水试验,取得场地承压含水层水文地质参数及降水引起的沉降特征,为地下空间设计和施工提供可靠依据。本次布设抽水井、观测井、分层沉降标组、孔隙水压力观测孔及地面沉降观测点,依据抽水试验技术要求获取渗透系数、抽水影响半径等相关水文地质参数。最后,针对工程场地内承压水情况及特点进行分析,提出基坑开挖时的承压水降压建议方案。     

高压旋喷桩单桩承载力分析

高压喷射注浆于1968年首创于日本。我国于20世纪70年代初相继引进并开始研究高压喷射注浆技术。目前,高压旋喷工艺应用最为广泛,工艺技术最为成熟。对旋喷桩成桩质量及单桩承载力进行研究分析,为旋喷桩在地基与基础工程、水利水电工程、止水、加固工程中的应用提供设计参考依据。该试验在陕西省延安市某建成小区内选三个试验点,按不同旋喷桩施工工艺成桩,通过对桩身完整性检测、单桩承载力试验,分析旋喷桩成桩质量及单桩承载力。     

Seismic fracture evaluation of diaphragm joints in welded beam-to-box column moment connections

Steel box columns are widely used in steel building structures in Taiwan due to their dual strong axes. To transfer the beam-end moment to the column, diaphragm plates of the same thickness and elevations as the beam flanges are usually welded inside the box column. The electro-slag welding (ESW) process is widely used to connect the diaphragms to the column flanges in Taiwan because of its convenience and efficiency. However, ESW may increase the hardness of the welds and heat-affected zones (HAZs), while reducing the Charpy-V notch strength in the HAZ. This situation can cause premature fracture of the diaphragm-to-column flange welds before a large plastic rotation is developed in the beam-to-box column joints. To quantify the critical eccentricity and the effectiveness of fracture prediction, this study uses fracture prediction models and finite element model (FEM) analysis to correlate the test results. In this study, two beam-to-box column connection subassembly tests are conducted with different loading protocols and ESW chamber shapes. To implement a fracture prediction model, the material parameters are established from circumferential notched tensile tests and FEM analysis. Test results indicate that the fracture instances can be predicted on the basis of the cumulative plastic deformation in the HAZs. Analytical results indicate that fracture instances and locations are sensitive to the relative locations of the ESW joints and beam flange. Tests also confirm that the possible fracture of the diaphragm-to-column flange joints can be mitigated by enlarging the chamber of the ESW joint.     

Response of a scale-model pile group for a jacket foundation of an offshore wind turbine in liquefiable ground during shaking table tests

To investigate the seismic response of a pile group during liquefaction, shaking table tests on a 1/25 scale model of a 2 × 2 pile group were conducted, which were pilot tests of a test project of a scale-model offshore wind turbine with jacket foundation. A large laminar shear box was utilized as the soil container to prepare a liquefiable sandy ground specimen. The pile group model comprising four slender aluminum piles with their pile heads connected by a rigid frame was designed with similitude considerations focusing on soil–pile interaction. The input motions were 2-Hz sinusoids with various acceleration amplitudes. The excess pore water pressure generation indicated that the upper half of the ground specimen reached initial liquefaction under the 50-gal-amplitude excitation, whereas in the 75-gal-amplitude test, almost entire ground was liquefied. Accelerations in soil, on the movable frames composing the laminar boundary of the shear box, and along the pile showed limited difference at the same elevation before liquefaction. After liquefaction, the soil and the movable-frame accelerations that represented the ground response considerably reduced, whereas both the movable frames and the piles exhibited high-frequency jitters other than 2-Hz sinusoid, and meantime, remarkable phase difference between the responses of the pile group and the ground was observed, all probably due to the substantial degradation of liquefied soil. Axial strains along the pile implied its double-curvature bending behavior, and the accordingly calculated moment declined significantly after liquefaction. These observations demonstrated the interaction between soil and piles during liquefaction.     

Investigating the vibration properties of integrated ceiling systems considering interactions with surrounding equipment

Studies on recent earthquakes highlighted that buildings with minimal structural damage still suffer from extensive damage and failure of nonstructural components. The dropping and damage of suspended ceiling systems, which typically consist of acceleration-sensitive nonstructural elements, resulted in lengthy functional disruptions and extended recovery time. This article experimentally and analytically examined the vibration properties of an integrated ceiling system considering the interactions with surrounding electrical equipment. The theoretical stiffness and corresponding frequency of electrical equipment were initially derived and then verified by subsequent vibration tests and numerical analyses. The seismic performance of the air conditioner (AC) was evaluated with different installment configurations based on design spectra and floor response spectra. Vibration tests of the suspended integrated ceiling system considering the interactions with surrounding equipment showed that the inclusion of peripheral constraints increased the first horizontal vibration frequency of the ceiling system by a factor of approximately 6. The natural frequencies of all components in the integrated ceiling system were almost identical, which was attributed to the coupled behavior between the ceiling panels and surrounding equipment, emphasizing the effect of interactions between adjacent components during dynamic analysis. Based on the above experimental investigation, an associated numerical model of the integrated ceiling system was created. Finally, corresponding parametric studies that included the interactions with surrounding equipment, reinforcing braces of ACs and strengthening members at the rise-up location between two elevations were performed.     

建筑抗震实时混合试验时滞补偿方法研究综述

时滞补偿是建筑抗震实时混合试验的重要问题。文章对时滞补偿方法的研究进行总结,将时滞补偿方法分为基于时间的位移预测时滞补偿方法、基于反馈力的位移预测时滞补偿方法、基于加载系统模型求逆的时滞补偿方法、基于控制理论的时滞补偿方法和基于集成理念的综合补偿方法。