Comparative response analysis of conventional and innovative seismic protection strategies

The paper presents a numerical investigation aimed at evaluating the improvements achievable through devices for passive seismic protection of buildings based on the use of shape memory alloys (SMA) in place of conventional steel or rubber devices. To get some generality in the results, different resisting reinforced concrete plane frames were analysed, either protected or not. ‘New’ and ‘existing’ buildings were considered depending on whether seismic provisions are adopted in the building design or not. Base isolation and energy dissipation were equally addressed for both conventional and innovative SMA‐based devices. Fragility analyses were performed using specific damage measures to account for comparisons among different damage types; the results were then used to estimate quantitatively the effectiveness of the various protection systems. More specifically, the assessment involved a direct comparison of the damage reduction provided by each protection system with respect to the severe degradation experienced by the corresponding non‐protected frame. Structural damage, non‐structural damage and damage to contents were used on purpose and included in a subsequent phase of cost analysis to evaluate the expected gains also in terms of economic benefits and life loss prevention. The results indicate that base isolation, when applicable, provides higher degrees of safety than energy dissipation does; moreover, the use of SMA‐based devices generally brings about better performances, also in consideration of the reduced functional and maintenance requirements. Copyright © 2002 John Wiley & Sons, Ltd.     

Seismic response of self‐centring hysteretic SDOF systems

The seismic response of single‐degree‐of‐freedom (SDOF) systems incorporating flag‐shaped hysteretic structural behaviour, with self‐centring capability, is investigated numerically. For a SDOF system with a given initial period and strength level, the flag‐shaped hysteretic behaviour is fully defined by a post‐yielding stiffness parameter and an energy‐dissipation parameter. A comprehensive parametric study was conducted to determine the influence of these parameters on SDOF structural response, in terms of displacement ductility, absolute acceleration and absorbed energy. This parametric study was conducted using an ensemble of 20 historical earthquake records corresponding to ordinary ground motions having a probability of exceedence of 10% in 50 years, in California. The responses of the flag‐shaped hysteretic SDOF systems are compared against the responses of similar bilinear elasto‐plastic hysteretic SDOF systems. In this study the elasto‐plastic hysteretic SDOF systems are assigned parameters representative of steel moment resisting frames (MRFs) with post‐Northridge welded beam‐to‐column connections. In turn, the flag‐shaped hysteretic SDOF systems are representative of steel MRFs with newly proposed post‐tensioned energy‐dissipating connections. Building structures with initial periods ranging from 0.1 to 2.0s and having various strength levels are considered. It is shown that a flag‐shaped hysteretic SDOF system of equal or lesser strength can always be found to match or better the response of an elasto‐plastic hysteretic SDOF system in terms of displacement ductility and without incurring any residual drift from the seismic event. Copyright © 2002 John Wiley & Sons, Ltd.     

A recursive decomposition algorithm for network seismic reliability evaluation

A new probabilistic analytical approach to evaluate seismic system reliability of large lifeline systems is presented in this paper. The algorithm takes the shortest path from the source to the terminal of a node weight or edge weight network as decomposition policy, using the Boolean laws of set operation and probabilistic operation principal, a recursive decomposition process then could be constructed. For a general weight network, the modified Torrieri method (NTR/T method) is introduced to combine with the suggested algorithm. Therefore, the recursive decomposition algorithm may be applied to evaluate the seismic reliability of general lifeline systems. A series of case studies, including a practical district electric power network system and a large urban water supply system, show that the suggested algorithm supplies a useful probabilistic analysis means for the seismic reliability evaluation of large lifeline systems. Copyright © 2002 John Wiley & Sons, Ltd.     

A response‐based decoupling criterion for multiply‐supported secondary systems

It is often infeasible to carry out coupled analyses of multiply‐supported secondary systems for earthquake excitations. ‘Approximate’ decoupled analyses are then resorted to, unless the response errors due to those are significantly high. This study proposes a decoupling criterion to identify such cases where these errors are likely to be larger than an acceptable level. The proposed criterion is based on the errors in the primary system response due to decoupling and has been obtained by assuming (i) the input excitation to be an ideal white noise process, (ii) cross‐modal correlation to be negligible, and (iii) the combined system to be classically damped. It uses the modal properties of the undamped combined system, and therefore, a perturbation approach has been formulated to determine the combined system properties in case of light to moderately heavy secondary systems. A numerical study has been carried out to illustrate the accuracy achieved with the proposed perturbation formulation. The proposed decoupling criterion has been validated with the help of two example primary‐secondary systems and four example excitation processes. Copyright © 2002 John Wiley & Sons, Ltd.     

Pseudodynamic tests on rubber base isolators with numerical substructuring of the superstructure and strain‐rate effect compensation

A pseudodynamic testing procedure has been applied by which the seismic response of a base‐isolated building is obtained by using as specimen the isolators, while the superstructure is numerically simulated. The procedure also takes advantage of the continuous pseudodynamic testing capabilities of the ELSA laboratory, which increase the accuracy of the results and reduce the strain‐rate effect of the rubber bearings. A simple proportional correction of the measured forces compensates the remaining strain‐rate effect due to the unrealistic speed of the test. The correction factor is obtained by means of a characterizing test on the specific rubber isolators. The developed method has been successfully applied to the prediction of the seismic response of a base‐isolated four‐storey building submitted to several specified accelerograms. The results for those earthquakes as well as the effects of some changes of the parameters of the system are discussed. Copyright © 2002 John Wiley & Sons, Ltd.     

Study on effects of damping in laminated rubber bearings on seismic responses for a ⅛ scale isolated test structure

The effects of damping in various laminated rubber bearings (LRB) on the seismic response of a ?‐scale isolated test structure are investigated by shaking table tests and seismic response analyses. A series of shaking table tests of the structure were performed for a fixed base design and for a base isolation design. Two different types of LRB were used: natural rubber bearings (NRB) and lead rubber bearings (LLRB). Three different designs for the LLRB were tested; each design had a different diameter of lead plug, and thus, different damping values. Artificial time histories of peak ground acceleration 0.4g were used in both the tests and the analyses. In both shaking table tests and analyses, as expected, the acceleration responses of the seismically isolated test structure were considerably reduced. However, the shear displacement at the isolators was increased. To reduce the shear displacement in the isolators, the diameter of the lead plug in the LLRB had to be enlarged to increase isolator damping by more than 24%. This caused the isolator stiffness to increase, and resulted in amplifying the floor acceleration response spectra of the isolated test structure in the higher frequency ranges with a monotonic reduction of isolator shear displacement. Copyright © 2002 John Wiley & Sons, Ltd.     

地震勘探资源频率域叠加方法研究

在叠前共深度点道集内各地震道的动、静校正误差很小的情况下，地震资料时间域水平叠加方法有较好的叠加结果。但是，如果动、静校正的误差较大时，叠加效果将受到影响，即叠后振幅和分辨率都会降低。因此，提出一种频率域叠加方法。该方法既具有常规水平叠加方法能提高信噪比的优点，又能将共深度点道集内的走时时差消除，达到内相叠回的目的。几个比较叠加方法效果的有噪CDP道集叠加的例子证明了该方法的效果。     

Seismic Hazard for Selected Sites in Greece: A Bayesian Estimate of Seismic Peak Ground Acceleration

A procedure for estimating maximum values of seismic peak ground accelerationat the examined site and quantiles of its probabilistic distribution in a future timeinterval of a given length is considered. The input information for the method areseismic catalog and regression relation between peak seismic acceleration at a givenpoint and magnitude and distance from the site to epicenter (seismic attenuation law).The method is based on Bayesian approach, which simply accounts for influenceof uncertainties of seismic acceleration values. The main assumptions for the method are Poissonian character of seismic events flow and distribution law of Gutenberg-Richter's type. The method is applied to seismic hazard estimation in six selected sitesin Greece.     

An automated strategy for calculation of phase diagram sections and retrieval of rock properties as a function of physical conditions

We formulate an algorithm for the calculation of stable phase relations of a system with constrained bulk composition as a function of its environmental variables. The basis of this algorithm is the approximate representation of the free energy composition surfaces of solution phases by inscribed polyhedra. This representation leads to discretization of high variance phase fields into a continuous mesh of smaller polygonal fields within which the composition and physical properties of the phases are uniquely determined. The resulting phase diagram sections are useful for understanding the phase relations of complex metamorphic systems and for applications in which it is necessary to establish the variations in rock properties such as density, seismic velocities and volatile‐content through a metamorphic cycle. The algorithm has been implemented within a computer program that is general with respect to both the choice of variables and the number of components and phases possible in a system, and is independent of the structure of the equations of state used to describe the phases of the system.     

Structure sismique du socle paléozoı̈que du bassin des Doukkala,Môle côtier,Maroc occidental. Indication en faveur de l'existence d'une phase éo-varisqueSeismic structure of the Doukkala basin,Palaeozoic basement,western Morocco: a hint for an Eovariscan fold-and-thrust belt

Seismic profiles and well data from the Doukkala basin unravel the structure of the Palaeozoic basement and suggest that this coastal zone of western Morocco was affected by a compressive phase during the Frasnian. This resulted in the formation of upright, plurikilometric folds associated with reverse faults (North Doukkala), and of asymmetrical folds associated with mostly west verging ramps (South Doukkala). Folding involved all pre-Upper Frasnian formations and caused partial or total hiatus of Upper Frasnian–Strunian strata. This event can be correlated with the orogenic phase reported from more internal domains of the Morocco Hercynian belt, where it is referred to as the ‘Bretonne’ or ‘Eovariscan’ phase. To cite this article: H. Echarfaoui et al., C. R. Geoscience 334 (2002) 13–20