磁浮交通试验线压力管道直线度的测量方法研究及应用

目前,国内外对于磁浮交通真空压力管道直线度测量问题的研究较少。本文结合西南交通大学在建的真空磁浮高速列车试验装置,提出了一种真空压力管道直线度测量方法。该方法在管道内建立高精度=维控制网,依据三维控制网测量采用圆曲线拟合方法确定各节管道的圆心坐标,并采用直线拟合方法分析整个管道的直线度。最后依据上述方法编制程序对实测数据进行了处理分析,验证了方法的可行性和正确性,可为今后真空磁浮压力管道的建设提供技术参考。     

Direct numerical simulation of flow over a slotted cylinder at low Reynolds number

Direct numerical simulation was conducted to investigate the flow past a slotted cylinder at low Reynolds number (Re) of 100. The slotting of cylinder affects the boundary layer separation, vortex formation position, recirculation region length and wake width, which are determined by the type of slit. The streamwise slit (SS1), T-shaped slit (SS3) and Y-shaped slit (SS4) act as passive jets, while the transverse slit (SS2) achieves an alternate self-organized boundary layer suction and blowing. The flow rate in slits fluctuates over time due to the alternate vortex shedding and fluctuating pressure distribution around the cylinder surface. One fluctuation cycle of flow rate is caused by a pair of vortices shedding for SS2, SS3 and SS4, while it is created by each vortex shedding for SS1. The wall shear stress and flow impact on the slit wall partly contribute to the hydrodynamic forces acting on the slotted cylinder. Taking into account the internal wall of slit, the transverse slit plays the best role in suppressing the fluid forces with drag reduction of 1.7% and lift reduction of 17%.     

Hydrodynamic forces on a partially submerged cylinder at high Reynolds number in a steady flow

The hydrodynamic forces on the stationary partially submerged cylinder are investigated through towing test with Reynolds number ranging from 5 × 10⁴ to 9 × 10⁵. Three test groups of partially submerged cylinders with submerged depths of 0.25 D, 0.50 D, and 0.75 D and one validation group of fully submerged cylinders are conducted. During the experiments, the hydrodynamic forces on the cylinders are measured using force sensors. The test results show a considerable difference in the hydrodynamic coefficients for the partially submerged cylinders versus the fully submerged cylinders. A significant mean downward lift force is first observed for the partially submerged cylinders in a steady flow. The maximum of the mean lift coefficients can reach 1.5. Two distinct features are observed due to the effects of overtopping: random distributions in the mean drag coefficients and a clear quadratic relationship between the mean lift coefficients and the Froude number appear in the non-overtopping region. However, the novel phenomenon of a good linear relationship with the Froude number for the mean hydrodynamic coefficients is clearly shown in the overtopping region. In addition, fluctuating hydrodynamic coefficients are further proposed and investigated. These results are helpful to have a better understanding of the problem and to improve related structural designs.     

Semi-analytical solution for the water wave diffraction by arrays of truncated circular cylinders in front of a vertical wall

The present study investigates the combined wave field that is induced by the continuous interaction of plane waves with an array of truncated circular cylinders in front of a rigid wall. The long-term goal of the study is the investigation of possible increase in the efficiency of cylindrical Wave Energy Converters (WECs) by putting in the vicinity of the array a barrier to propagation, a wall, that could assist the reflection of the incoming waves. The main task is to develop a generic solution method that is free of conceptual simplifications employed, e.g. by the method of images and the assumption of “pure” wave reflection. To cope with the set task, the proposed method relies on the semi-analytical formulation of the velocity potentials, while the solution is sought by combined expressions that involve polar and elliptical harmonics. The wall is represented as an elliptical cylinder with zero semi-minor axis. This assumption has eventually a beneficial effect to the underlying formulation given that it simplifies significantly the expansions of the involved diffraction potentials.     

载人潜水器圆柱形耐压壳体的优化设计研究

采用分枝定界法和序列二次规划方法,对载人潜水器圆柱形耐压壳体的重量最小化进行了研究.设计变量是壳板的厚度、肋骨的型号、间距和数量,讨论了下潜深度、材料几何参数对重量以及其它特征量的影响.算例计算表明,下潜深度越大,屈服极限越高的材料重量减轻越明显.对于大深度而言,选用高屈服极限材料,可以使得材料能够充分利用.文中还对结构重量占排水量比例随深度变化的情况进行了研究.     

不同固有频率比条件下圆柱双自由度涡激振动特性的数值研究

采用RANS方法,结合SST k-ω湍流模型,对不同顺流向与横顺流向固有频率的比值(即固有频率比,fnx/fny)条件下低质量比圆柱体的双自由度涡激振动进行了二维数值模拟。圆柱体的质量比为2.6,雷诺数范围为2 500~18 750,相应的约化速度范围为2~15,包括了经典试验中出现的整个锁定范围。通过研究发现,固有频率比是影响振动特性的重要参数,随着固有频率比的增加,响应幅值逐渐降低且向更高的约化速度偏移;在低约化速度范围内,固有频率比对顺流向和横流向振动之间的相位差以及升力频率有较大影响,从而得到各种不同偏向的8字形轨迹;最后对不同固有频率比条件下的尾涡模式进行了讨论,给出了对应不同约化速度时的尾涡模式。     

圆形数值波浪水池斜向和多向入射波浪模拟研究

为了研究斜向入射波浪,基于三维不可压缩两相流模型,开发了一套圆形数值波浪水池数值模型。在圆形波浪水池中,通过源项造波法成功生成了任意入射方向的波浪,并且利用人工摩擦项模拟阻尼区以数值耗散反射波浪。模型基于嵌入式多块网格体系,采用FVM法(finite volume method)离散Navier-Stokes方程,VOF法(volume of fluid)追踪自由水面。试验结果表明,斜向入射波浪的模拟结果与理论值基本一致,圆形波浪水池在模拟斜向入射波浪时,有效区域的面积较传统波浪水池显著增大,而且有效区域受波浪入射角度的影响也较小。同时,通过叠加多列斜向入射波浪,模拟出了多向交叉波列,并通过与理论结果对比,发现其具有较高的精度。     

玉米深加工产业的循环经济模式研究

玉米深加工具有典型的替代能源及循环经济特征。目前玉米深加工行业面临的资源短缺和环境污染的双重制约。从促进经济与环境协调发展的角度,结合玉米深加工产业发展及环境治理现状,对玉米深加工产业的循环经济模式——玉米深加工生态产业园区建设进行了探索。通过对玉米深加工生态产业园上下游原料产业链的延伸、各环节废物的资源化分析、能源与水资源回收利用的设计和生态产业园区外围企业关系的研究,结果表明,通过实施清洁生产和延长产业链,构建闭合循环的玉米深加工生态产业链条,可实现资源、能源的有效节约和副产品、废弃物的综合利用,具有相应的环境、经济和社会效益,在增强企业绿色竞争力的同时可促进玉米深加工产业的可持续发展。该模式对吉林省及同类地区玉米深加工产业的可持续发展有指导和借鉴意义。     

不同排列方式和间隙比下双圆柱流致振动特性研究

采用基于ALE的流固耦合分析方法,将圆柱体振动模型简化为平面双自由度质量-弹簧-阻尼系统,进行了计算参数无关性分析。对不同θ角和间隙比T下的双圆柱流致振动进行数值模拟,并与单圆柱振动计算结果进行比较,得到了不同θ角和间隙比T下中心圆柱的升阻力系数、流场分布和运动轨迹变化情况。通过分析发现小间隙比下由于两圆柱间的相互干扰,改变了中心圆柱的尾涡结构,导致了升力和阻力系数随不同θ角而发生变化;小间隙比下由于两圆柱间的相互干扰影响,均使中心圆柱的轨迹在不同θ角下发生了较大的变化,顺流向的振动频率与单圆柱振动时相比出现了多倍频,导致其运动轨迹发生了变化。     

基于圆柱多段拟合的隧道中轴线提取方法研究

提出基于圆柱多段拟合的隧道中轴线提取方法。首先对隧道点云数据进行预处理,并将点云按隧道走向分成不同区段;然后对各区段依据轴线与表面点云法线垂直关系,提取精度较低的中轴线;最后对各区段利用圆柱多段拟合,提取精度较高的中轴线。实验表明,隧道中轴线的提取在一定的采样区间具有较高的稳定性,对直线和弯曲的圆形隧道有良好的适用性,算法可靠,精度较高。