应用RMi法估算岩体变形模量

RMR法与Q法是国内外八、九十年代岩体质量和参数估算的常用方法,然而RMR法和Q法对质量较差的岩体不太实用,而RMi法是一种既适用于软岩又适用于硬岩的岩体质量评价和参数估算方法。本文在介绍RMi法基本原理的基础上,对贵州省鱼简河水库坝基岩体变形模量进行确定。     

GPS-measured land subsidence in Ojiya City, Niigata Prefecture, Japan

Land subsidence caused by compression of clay layers in Ojiya City, Japan was measured by global positioning system (GPS) between 1 April 1996 and 31 December 1998.

Three baselines were selected in and around the city, and height difference on a WGS-84 ellipsoid was measured by GPS on each baseline. The ground at the GPS station in the city subsides and rebounds 7 cm every winter and spring, respectively. Measurement accuracy was 9.5 mm standard deviation. Ground water level was observed at a well near the GPS station. Regression analysis between total strain, calculated as ratio of the height difference displacement to the total thickness of the clay layers, and the layers' effective stress change with ground water level change gave good correlation. The slope of regression line 7.0×10⁻¹¹ m²/N was obtained as an average apparent coefficient of volume compressibility of the layers.     

Digital model of corrected accumulated flow for peak discharge data acquisition and drainage system design

The design of a drainage system for a roofing slate quarry was implemented by the enhancement of discharge peak estimation, and the uncertainty inevitably associated with the engineering model was reduced.

The development of a topographical, geological, and vegetation cover database developed from a Geographical Information System (GIS) allowed for the definition of the drainage network for a hydraulic system, along with the calculation of the runoff coefficient. This is applied to the digital model of accumulated flow (DMF) as a weight correction coefficient, using a matrix-based model at 5×5 m resolution. The new digital model of corrected accumulated flow (DMCF) is the result of combining the thematic maps with the map of slope <3%, which was previously created from the slope model. It is demonstrated that this new model allows to apply the “Rational Method” on cartographic units defined by the GIS.

The DMCF is compared with other traditional applications of the Rational Method based on the calculation of the discharge peak considering: (1) the drainage basin as a single watershed or (2) defining an average runoff coefficient in each sub-watershed. Both approaches have bigger discharge peaks than those obtained by the DMCF since the slope, lithology, and vegetation cover have average values, and the runoff coefficient is poorly defined, increasing the uncertainty in the discharge peak.     

A Procedure for Determining the Reaction Curve of Shotcrete Lining Considering Transient Conditions

Summary The mechanical behaviour of a shotcrete lining is analysed in this paper using the convergence-confinement approach. A calculation procedure is presented which is able to provide the reaction curve of a lining with increasing stiffness, by taking into account the variability due to time of the shotcrete stiffness and strength, as well as the face advancement rate. The proposed procedure is also able to provide the change of the safety factor of the lining in time. This results to be a very useful tool for understanding the behaviour of this widely used support and for assigning its thickness to guarantee stability (also in transient conditions), with a known safety factor, during tunnel excavation. Received May 25, 2001; accepted July 18, 2002; Published online January 21, 2003 Acknowledgements The author would like to thank Prof. S. Pelizza and Dr. S. Xu for the help given during the preparation of this paper. The help of the Editor G. Barla is also acknowledged. Authors' address: Dr. P. P. Oreste, Department of Earth Resources and Land, Politecnics di Torino, corso Duca degli Abruzzi 24, 1-10129 Torino, Italy; e-mail: oreste@polito.it     

Geomechanical Properties of Shear Zones in the Eastern Aar Massif,Switzerland and their Implication on Tunnelling

Summary ¶Rock zones containing a high fracture density and/or soft, low cohesion materials can be highly problematic when encountered during tunnel excavation. For example in the eastern Aar massif of central Switzerland, experiences during the construction of the Gotthard highway tunnel showed that heavily fractured areas within shear zones were responsible for overbreaks in the form of chimneys several metres in height. To understand and estimate the impact of the shear zones on rock mass behaviour, knowledge concerning the rock mass strength and deformation characteristics is fundamental. A series of laboratory triaxial tests, performed on samples from granite- and gneiss-hosted shear zones revealed that with increasing degree of tectonic overprint, sample strength decreases and rock behaviour shows a transition from brittle to ductile deformation. These trends may be explained by increasing fracture densities, increasing foliation intensity, increasing thickness of fine-grained, low cohesion fracture infill, and increasing mica content associated with the increasing degree of tectonic overprint. As fracture density increases and the influence of discrete, persistent discontinuities on rock mass strength decreases, behaviour of the test samples becomes more and more representative of rock mass behaviour, i.e. that of a densely fractured continuum. For the purpose of numerical modeling calculations, the shear zones may be subdivided with respect to an increasing fracture density, foliation intensity and mica content into a strongly foliated zone, a fractured zone and a cohesionless zone, which in turn exhibit brittle, brittle-ductile and ductile rock mass constitutive behaviour, respectively.Received December 17, 2001; accepted January 9, 2003 Published online April 29, 2003     

Flood Damage Reduction Program (FDRP) in Québec: Case Study of the Chaudiére River

This study presents the evolution of agreements between the governments of Canadaand Québec on flood damage reduction. In Québec, the implementation of a regulation about building in floodplains came about in 1983–1984. Today, this regulation takes the form of a policy called ``Policy of shores, littoral and floodplain protection'. Municipalities must adopt rules that concur with the principles of this policy.The Chaudiére River basin was selected for analysis of urban developmentduring the period following the application of building rules in flood-risk areas.Despite the ban on building in the strong current zone (0–20 year return periodflood zone), many buildings, essentially residential, have been erected in thiszone. These new constructions generally account for a low percentage of thetotal property value in the 0–100 year flooding area, but are legal since theyare connected to a water and sewage network that existed prior to the officialfloodplain regulation.Flood damage along the Chaudiére River will tend to increase for two reasons.Firstly, while respecting the policy mentioned above, sites are still available infloodplains for future development. Secondly, no structural flood protection workshave been erected in view of the fact they are only marginally profitable from anbenefit-cost point of view.     

Chemical, Isotopic, and Fluid Inclusion Evidence for the Hydrothermal Alteration of the Footwall Rocks of the BIF-Hosted Iron Ore Deposits in the Hamersley District, Western Australia

Abstract. The petrography, chemical, fluid inclusion and isotope analyses (O, Rb-Sr) were conducted for the shale samples of the Mount McRae Shale collected from the Tom Price, Newman, and Paraburdoo mines in the Hamersley Basin, Western Australia. The Mount McRae Shale at these mines occurs as a footwall unit of the secondary, hematite-rich iron ores derived from the Brockman Iron Formation, one of the largest banded iron formations (BIFs) in the world. Unusually low contents of Na, Ca, and Sr in the shales suggest that these elements were leached away from the shale after deposition. The δ¹⁸O (SMOW) values fall in the range of + 15.0 to +17.9 per mil and show the positive correlation with calculated quartz/sericite ratios of the shale samples. This suggests that the oxygen isotopic compositions of shale samples were homogenized and equilibrated by postdepositional event. The pyrite nodules hosted by shales are often rimmed by thin layers of silica of varying crystallinity. Fluid inclusions in quartz crystals rimming a pyrite nodule show homogenization temperatures ranging from 100 to 240C for 47 inclusions and salinities ranging from 0.4 to 12.3 wt% NaCl equivalent for 18 inclusions. These fluid inclusion data give direct evidence for the hydrothermal activity and are comparable to those of the vein quartz collected from the BIF-derived secondary iron ores (Taylor et al, 2001). The Rb-Sr age for the Mount McRae Shale is 1,952 ± 289 Ma and at least 200 million years younger than the depositional age of the Brockman Iron Formation of ∼ 2.5 Ga in age. All the data obtained in this study are consistent with the suggestion that high temperature hydrothermal fluids were responsible for both the secondary iron ore formation and the alteration of the Mount McRae Shale.     

青藏高原1∶25万区域地质调查地貌年代学研究

高原隆升及剥蚀作用的复杂性与区域差异性以及高原恶劣的气候、地理条件,使得在青藏高原空白区1∶25万区域地质调查中进行地貌年代学研究具有很大的现实意义.由于地貌是高原隆升、环境演化、新构造运动等的信息载体,地貌年代有助于重塑这些地质作用的发生时间及发展过程,因此地貌年代学研究具有重要的技术意义.1∶25万银石山幅的工作表明,地貌年代学调查对高原隆升及环境演化过程研究具有良好效果.     

The anisotropy of magnetic susceptibility in biotite, muscovite and chlorite single crystals

The anisotropy of magnetic susceptibility (AMS) of single crystals of biotite, muscovite and chlorite has been measured in order to provide accurate values of the magnetic anisotropy properties for these common rock-forming minerals. The low-field AMS and the high-field paramagnetic susceptibility are defined. For the high-field values, it is necessary to combine the paramagnetic deviatoric tensor obtained from the high-field torque magnetometer with the paramagnetic bulk susceptibility measured from magnetization curves of the crystals. This leads to the full paramagnetic susceptibility ellipsoid due to the anisotropic distribution of iron cations in the silicate lattice. The ellipsoid of paramagnetic susceptibility, which was obtained for the three phyllosilicates, is highly oblate in shape and the minimum susceptibility direction is subparallel to the crystallographic c-axes. The anisotropy of the susceptibility within the basal plane of the biotite has been evaluated and found to be isotropic within the accuracy of the instrumental measurements. The degree of anisotropy of biotite and chlorite is compatible with previously reported values while for muscovite the smaller than previously published values. The shape of the chlorite AMS ellipsoid for all the samples is near-perfect oblate in contrast with a wide distribution of oblate and prolate values reported in earlier studies. Reliable values are important for deriving models of the magnetic anisotropy where it reflects mineral fabrics and deformation of rocks.     

From geometry to dynamics of microstructure: using boundary lengths to quantify boundary misorientations and anisotropy

The microstructure of a quartzite experimentally deformed and partially recrystallised at 900 °C, 1.2 GPa confining pressure and strain rate 10⁻⁶/s was investigated using orientation contrast and electron backscatter diffraction (EBSD). Boundaries between misoriented domains (grains or subgrains) were determined by image analysis of orientation contrast images. In each domain, EBSD measurements gave the complete quartz lattice orientation and enabled calculation of misorientation angles across every domain boundary. Results are analysed in terms of the boundary density, which for any range of misorientations is the boundary length for that range divided by image area. This allows a more direct comparison of misorientation statistics between different parts of a sample than does a treatment in terms of boundary number.The strain in the quartzite sample is heterogeneous. A 100×150 μm low-strain partially recrystallised subarea C was compared with a high-strain completely recrystallised subarea E. The density of high-angle (>10°) boundaries in E is roughly double that in C, reflecting the greater degree of recrystallisation. Low-angle boundaries in C and E are produced by subgrain rotation. In the low-angle range 0–10° boundary densities in both C and E show an exponential decrease with increasing misorientation. The densities scale with exp(−θ/λ) where λ is approximately 2° in C and 1° in E; in other words, E has a comparative dearth of boundaries in the 8–10° range. We explain this dearth in terms of mobile high-angle boundaries sweeping through and consuming low-angle boundaries as the latter increase misorientation through time. In E, the density of high-angle boundaries is larger than in C, so this sweeping would have been more efficient and could explain the relative paucity of 8–10° boundaries.The boundary density can be generalised to a directional property that gives the degree of anisotropy of the boundary network and its preferred orientation. Despite the imposed strain, the analysed samples show that boundaries are not, on average, strongly aligned. This is a function of the strong sinuosity of high-angle boundaries, caused by grain boundary migration. Low-angle boundaries might be expected, on average, to be aligned in relation to imposed strain but this is not found.Boundary densities and their generalisation in terms of directional properties provide objective measures of microstructure. In this study the patterns they show are interpreted in terms of combined subgrain rotation and migration recrystallisation, but it may be that other microstructural processes give distinctive patterns when analysed in this fashion.