基于最大球算法定量表征土体空间孔隙网络

孔隙网络控制着土体渗流、排水固结与基质吸力等重要工程性质。本文介绍了多孔介质孔隙网络最大球建模基本原理与算法。以显微CT扫描振捣干法生成的南京粉砂试样为例,采用最大球算法建立了试样三维重构模型表征单元体(REV)的空间孔隙网络球棍模型,计算得到了样品REV尺度的孔隙网络参数,统计发现,孔隙半径、喉道半径、孔隙配位数、孔隙截面形状因子、喉道截面形状因子与喉道长度等孔隙参数均近似服从正态分布,孔隙体积近似服从衰减型指数分布。孔隙与喉道半径分别分布在100μm与65μm以内,两者数学期望分别为40. 0μm与18. 0μm;配位数分布在25以内,数学期望为5. 1;孔隙与喉道截面形状因子分别分布在0. 01~0. 04与0. 01~0. 05的区间内,两者数学期望分别为0. 019与0. 033;喉道长度分布在100~800μm以内,数学期望为292. 22μm。同时发现,样品中体积小于1. 5×10^7μm^3的小孔隙数量超过90%。本方法可应用于土体细观孔隙结构的定量表征。     

Development and Re‐Evaluation of Tourmaline Reference Materials for In Situ Measurement of Boron δ Values by Secondary Ion Mass Spectrometry

Six tourmaline samples were investigated as potential reference materials (RMs) for boron isotope measurement by secondary ion mass spectrometry (SIMS). The tourmaline samples are chemically homogeneous and cover a compositional range of tourmaline supergroup minerals (primarily Fe, Mg and Li end‐members). Additionally, they have homogeneous boron delta values with intermediate precision values during SIMS analyses of less than 0.6‰ (2s). These samples were compared with four established tourmaline RMs, that is, schorl IAEA‐B‐4 and three Harvard tourmalines (schorl HS#112566, dravite HS#108796 and elbaite HS#98144). They were re‐evaluated for their major element and boron delta values using the same measurement procedure as the new tourmaline samples investigated. A discrepancy of about 1.5‰ in δ¹¹B was found between the previously published reference values for established RMs and the values determined in this study. Significant instrumental mass fractionation (IMF) of up to 8‰ in δ¹¹B was observed for schorl–dravite–elbaite solid solutions during SIMS analysis. Using the new reference values determined in this study, the IMF of the ten tourmaline samples can be modelled by a linear combination of the chemical parameters FeO + MnO, SiO₂ and F. The new tourmaline RMs, together with the four established RMs, extend the boron isotope analysis of tourmaline towards the Mg‐ and Al‐rich compositional range. Consequently, the in situ boron isotope ratio of many natural tourmalines can now be determined with an uncertainty of less than 0.8‰ (2s).     

High‐Precision,High‐Accuracy Oxygen Isotope Measurements of Zircon Reference Materials with the SHRIMP‐SI

Analytical protocols for SHRIMP‐SI oxygen isotope analysis (δ¹⁸O) of a suite of zircon reference materials (RMs) are presented. Data reduction involved a robust estimate of uncertainties associated with the individual spot as well as for groups where the spot data are combined. The repeatability of δ¹⁸O measurements is dependent on both the analytical conditions and the choice of the primary reference material. Under optimised conditions, repeatability was often better than 0.4‰ (2s) allowing sample uncertainties to be obtained to better than 0.2‰ (at 95% confidence limit). Single spot uncertainty combined the within‐spot precision with the scatter associated with repeated measurements of the primary zircon reference material during a measurement session. The uncertainty for individual spots measured under optimised conditions was between 0.3 and 0.4‰ (at 95% confidence). The analytical protocols described were used to assess a variety of zircon RMs that have been used for geochronology and for which laser fluorination oxygen isotope data are available (Temora 2, FC1, R33, QGNG and Ple?ovice), as well as zircons that have been used as RMs for trace element or other types of determination (Mud Tank, Monastery, 91500, AS57, AS3, KIM‐5, OG1, SL13, CZ3 and several other Sri Lankan zircons). Repeated analyses over nine sessions and seven different mounts show agreement within analytical uncertainty for Temora 2, FC1, R33, QGNG, Ple?ovice and 91500, when normalised to Mud Tank. For existing ion microprobe mounts with these materials, an appropriate δ¹⁸O can be determined. However, care should be taken when using zircons from the Duluth Complex (i.e., FC1, AS57 and AS3) as reference materials as our data indicated an excess scatter on δ¹⁸O values associated with low‐U zircon grains.     

Discussion of user-defined parameters for recursive subspace identification: Application to seismic response of building structures

Structural damage assessment under external loading, such as earthquake excitation, is an important issue in structural safety evaluation. In this regard, an appropriate data analysis and system identification technique is required to interpret the measured data and to identify the state of the structure. Generally, the recursive system identification algorithm is used. In this study, the recursive subspace identification (RSI) algorithm based on the matrix inversion lemma algorithm with oblique projection technique (RSI-Inversion-Oblique) is applied to investigate the time-varying dynamic characteristics. The user-defined parameters used in the RSI-Inversion-Oblique technique are carefully discussed, which include the size of the data Hankel matrix (i), model order to extract the physical modes, and forgetting factor (FF) to detect the time-varying system modal frequencies. Response data from the Northridge earthquake from the Sherman Oaks building (CSMIP) is used as an example to examine a systematic method to determine the suitable user-defined parameters in RSI. It is concluded that the number of rows in the data Hankel matrix significantly influences the identification of the time-varying fundamental modal frequency of the structure. An algorithmic model order selection method using the eigenvalue distribution of RSI-Inversion can detect the system modal frequencies at each appending data window without causing any abnormality.     

基于桩间土滑动特性的合理桩间距研究

为研究抗滑桩合理桩间距以及荷载传递机制,首先以桩侧摩阻力为拱脚时的破裂面推导出以桩身为拱脚时的破裂角计算公式;然后引入对数螺旋线法确定桩间土体的滑移深度,以土拱效应为基础建立计算模型,求解考虑桩间土体滑移深度的合理桩间距表达式;最后对桩间净距的主要影响因素进行分析,包括滑坡推力、黏聚力、桩截面宽度以及高度。研究结果表明：由桩身和桩侧摩阻力同时作为土拱拱脚更符合实际受力状态,同时求得的土拱拱圈厚度和矢高小于以桩身为拱脚条件下相应值而大于以桩侧摩阻力为拱脚条件下的相应值,并且随桩埋深的增加而增大。     

洱海湖滨区蜻蜓物种多样性与环境影响因子关系初探

为探究洱海湖滨区环境因子与蜻蜓物种多样性之间的关系,2014年5月至2017年5月对洱海10个样点进行实地调查,记录植物20科46种,共采集蜻蜓11科22属28种1448个体,并对环境因子与蜻蜓多样性进行相关性分析.结果表明蜻蜓成虫多样性与植被丰富度、湿生植被覆盖度、挺水植被覆盖度和沉水植被覆盖度均呈正相关,与浮水植物覆盖度和人为干扰程度呈负相关;稚虫多样性与湖底底质和水体溶解氧呈正相关,并对结果进行了讨论.研究结果给洱海蜻蜓栖息地的保护及湖滨缓冲带生态修复提供了有益的参考和数据支持.     

铜绿微囊藻(Microcystis aeruginosa)次生代谢物对普通小球藻(Chlorella vulgaris)生长及有效量子产率的影响

浮游植物间的交互化感作用被认为是自然水体中浮游生物群落演替及优势种转换的主要因素之一.铜绿微囊藻(Microcystis aeruginosa)是富营养化湖泊中的常见蓝藻,其产毒品系相较非产毒品系具有较高的竞争优势,其产生的主要次生代谢产物微囊藻毒素-LR(MC-LR)通常被认为是重要的化感物质.但是到目前为止其在水生生态系中的生物学功能尚不明确.为探究并区分MC-LR及其他次生代谢产物对浮游植物的化感效应,本文研究了MC-LR与高浓度普通小球藻(Chlorella vulgaris)生长及有效量子产率的剂量—效应关系;比较了能够产生显著抑制效应的MC-LR、能够产生同等浓度MC-LR的产毒品系铜绿微囊藻滤液以及细胞粗提液对小球藻生长及有效量子产率的抑制效应.结果显示,MC-LR能够对小球藻生长及有效量子产率产生抑制作用,并且抑制率随着MC-LR浓度的增加而增大.在用200μg/L及以上浓度的MC-LR感染24 h后,叶绿素a浓度为1500μg/L的小球藻的生长与有效量子产率均比对照组显著降低.能够产生相同浓度MC-LR的产毒品系铜绿微囊藻细胞滤液对其没有产生显著影响,而其细胞粗提液却能够产生更强的抑制效应.与MCLR处理组相比,粗提液处理组小球藻的生长及有效量子产率分别降低了14%和3%.以上结果表明,MC-LR对普通小球藻的化感作用具有剂量依赖性;MC-LR之外的其他次生代谢物也能够产生抑制效应.     

安徽地区震源参数的相关性研究

基于安徽数字地震台网2010年1月至2017年12月记录到的ML2.5~5.0级地震,根据中小地震震源参数测定原理,利用多台多地震联合反演Atkinson方法和Moya方法分别计算了安徽地区地壳平均非弹性衰减因子Q值和安徽24个省属专业地震的台站场地。在此基础上,运用遗传算法求得安徽地区96个地震事件的震源谱参数,进而根据Brune中小地震圆盘模型计算其拐角频率、地震矩、应力降、矩震级、震源尺度等震源参数,并分析其特征及相互之间的关系。研究结果表明:安徽地区中小地震的ML震级与其他震源参数之间存在一定相关关系,而地震矩M0与应力降Δσ、震源尺度r和拐角频率fc之间并未表现出明显的相关关系。     

Flow resistance and hydraulic geometry in bedrock rivers with multiple roughness length scales

Many models of incision by bedrock rivers predict water depth and shear stress from discharge; conversely, palaeoflood discharge is sometimes reconstructed from flow depth markers in rock gorges. In both cases, assumptions are made about flow resistance. The depth–discharge relation in a bedrock river must depend on at least two roughness length scales (exposed rock and sediment cover) and possibly a third (sidewalls). A conceptually attractive way to model the depth–discharge relation in such situations is to partition the total shear stress and friction factor, but it is not obvious how to quantify the friction factor for rough walls in a way that can be used in incision process models. We show that a single flow resistance calculation using a spatially averaged roughness length scale closely approximates the partitioning of stress between sediment and rock, and between bed and walls, in idealized scenarios. Both approaches give closer fits to the measured depth–discharge relations in two small bedrock reaches than can be achieved using a fixed value of Manning's n or the Chézy friction factor. Sidewalls that are substantially rougher or smoother than the bed have a significant effect on the partitioning of shear stress between bed and sidewalls. More research is needed on how best to estimate roughness length scales from observable or measurable channel characteristics. © 2019 John Wiley & Sons, Ltd.     

宝兰客专天水市王家墩滑坡地震稳定性分析

天水市秦安县王家墩滑坡为宝兰客专沿线巨型古滑坡群,宝兰客运专线秦安隧道穿其而过。以王家墩滑坡为研究对象,围绕工程中静、动力抗滑稳定性问题,通过室内试验、现场调查对影响王家墩古滑坡稳定性的地质构造、场地工程条件等内在因素进行分析评价,在此基础上通过有限元动力分析,对王家墩古滑坡在地震载荷下的动力响应进行分析,明确地震荷载作用下,王家墩古滑坡失稳影响因素、地震荷载与滑坡失稳破坏间的关系。采用动力有限元法和强度折减法相结合的方法,开展动力抗滑稳定性分析方法研究;采用位移突变的方法来确定边坡动力失稳及动力安全系数,分析结果表明：地震作用时的水平推力对王家墩古滑坡的稳定性有很大影响,表现为上部坡体的整体滑移和隧道入口段黄土堆积层局部失稳滑塌;在天然状态下坡体处于稳定状态,在遭遇未来该区域中强地震作用时,该斜坡会发生失稳,黄土斜坡的整体滑动最容易出现在第三阶坡体,沿着塑性应变最大的滑移面整体滑移;给出了坡体动力稳定性安全系数F_s=0.92。