重力均衡与质量均衡

均衡理论，无论是艾礼模式，还是普拉特模式，都是建立在平面地壳的基础之上，并不考虑重力随高程的变化；这事实上相当于质量的均衡。如果在球面上考察均衡理论，并且考虑重力随高程的变化，则得到的均衡模型为重力的均衡。定量计算表明，质量均衡和重力均衡之间的差别是不可忽略的。这种差别对研究地壳的应力状态意义重大。     

岩体损伤力学研究进展

论述了岩体损伤力学在岩体力学中的地位，并从细观和宏观两个方面系统介绍了其最新研究进展；对岩体损伤力学研究中的几个重要问题提出了见解，认为分形几何是研究损伤的有效手段。     

岩体水力学概述

本文通过伙在工程活动与地质环境相互作用分析，揭示了人类工程、岩体与地下水之间的关系；论述了岩体水力学的研究对象，学科地位，研究内容以及研究方法。     

节理岩体断裂的分形机理研究

本文在考察了节理化岩体的断裂力学特征的基础上，结合现代分形几何原理，建立起追踪裂纹裂分形模型，对不连续岩体的断裂韧性的分形效应进行了深入研究，并通过压剪试验得到难。     

Identification of strength equilibrium rock slopes: Further statistical considerations

Strength equilibrium slopes are rock slopes whose gradient θ and rock mass strength (RMS) are in adjustment. The identification of such slopes depends on the accurate specification of the strength equilibrium envelope. Previous attempts to delimit the envelope are reviewed and modifications are proposed that permit its more rigorous statistical definition. Because θ can be measured much more reliably than RMS, the structural relation between these variables is estimated by regressing RMS on θ, and the strength equilibrium envelope is defined by the 95 per cent confidence limits. The analysis is performed on a data set of 268 rock slopes, representing all the data on RMS and θ hitherto employed in published studies of strength equilibrium slopes.     

土木工程结构的双层多重调谐质量阻尼器控制策略

为能得到用尽可能少的调谐质量阻尼器(TMD)组成有效性和鲁棒性高的多重调谐质量阻尼器控制系统，本文提出了一种适用于土木工程结构的新控制策略——双层多重调谐质量阻尼器(DMT—MD)。使用定义的优化目标函数，评价了双层多重调谐质量阻尼器(DMTMD)的控制性能。数值结果表明，双层多重调谐质量阻尼器(DMTMD)比多重凋谐质量阻尼器(MTMD)具有更好的有效性和对频率调谐的鲁棒性。DMTMD比双重调谐质量阻尼器(DTMD)具有更好的有效性，而DMTMD和DT—MD对频率调谐的鲁棒性近似相同。因此，双层多重调谐质量阻尼器是一种先进的结构控制策略。     

土-结构动力相互作用对结构控制的影响

本文研究了土-结构动力相互作用对采取不同控制措施的结构控制效果的影响。文中首先建立了主动调谐质量阻尼器(ATMD)、半主动磁流变阻尼器(MR)和被动多重调谐质量阻尼器(MTMD)等三种结构控制措施在时域中的控制算法和控制律，然后基于子结构法，采用间接边界元方法，通过傅里叶变换，推导了分别安装三种结构控制措施的受控结构在频域中的运动方程，数值仿真分析了某36层高层建筑的地震反应及其控制效果。结果表明，当采用ATMD或MTMD控制时，考虑土-结构动力相互作用后结构地震反应有所减小；当采用MR控制时，考虑土-结构动力相互作用后结构地震反应有很大程度的减小。由此看来，在设计软土地基上高层结构的结构控制措施时，不考虑土-结构动力相互作用对结构控制效果的影响是偏于安全的。     

A Combined Three-Dimensional Geological-Geostatistical-Numerical Model of Underground Excavations in Rock

Summary. This paper exploits geological and borehole geotechnical data obtained in the exploratory phase of a tunneling project to investigate in a first place if the kriging interpolation scheme may effectively reproduce the spatial variability of rock mass quality (Rock Mass Rating, RMR) in the vicinity of tunnels. For this purpose a quick solver in Fortran has been developed that performs variography analysis of 3D spatial data, fast kriging estimations of RMR between borehole sampling locations at the centroids of the elements of the numerical model, and model validation. For the purpose of an integrated underground excavation design, a step further is made by incorporating into the 3D mechanical numerical model of the rock mass, the three-dimensional (3D) solid geological model, thus coupling the geology with the ground (geotechnical) model (i.e. each element of the numerical model is assigned a geological material). The mechanical properties of each finite difference cell (or Representative Elementary Volume) of the ground model were then prescribed according to its geological type, the spatial heterogeneity of the rock mass expressed quantitatively with the kriging model, and the upscaling calculations of the mechanical properties of the intact rocks determined in the laboratory, based on the size-effect (strength dependence on size) and Damage Theory. Furthermore, a preliminary numerical simulation of the advance of unsupported tunnels in the model of the heterogeneous rock mass was performed for illustration purposes.     

Crustal Stress Measurement for Significant Project Construction and Its Application in Design

The hydrofracturing technique has developed into a reliable and practical method for determining the original three-dimensional crustal stress state of underground caverns,the load-bearing capacity of a high pressure cavern itself,and the high pressure hydraulic permeability of rock masses,and has also been extensively used in disposal of nuclear waste,long and deeply-buried traffic channels and high-pressure cavern engineering for hydraulic power plants.The practice shows that the comprehensive measurement of the physical parameters of the rock mass and taking full use of the wall rock load-bearing capacity to optimize the engineering design hold are very useful in ensuring the engineering safety and improving the design level.     

The visualization of turbulence data using a wavelet‐based method

This technical communication presents some MATLAB^® routines for visualizing the structure in turbulent signals based on a standard conditional averaging and thresholding approach. Up to three velocity components may be analysed and the resulting output highlights the time at which important flow events occur as well as the frequency levels that contribute the greatest energy to this particular event. The latter information is derived from a wavelet decomposition of the signal and may assist in providing a process‐based explanation of observed flow features. Copyright © 2006 John Wiley & Sons, Ltd.