银武高速公路同心至固原段边坡面蚀试验分析

为研究高速公路边坡面蚀,选择银武高速公路同心至固原段固原立交2.5 km范围作为研究区段,根据不同公路边坡类型和防治措施设置6个观测小区,采用插钎法测定坡面的面蚀量,同时由虹吸式自记雨量计记录降雨量。分别测定和计算了降雨量、降雨历时、平均降雨强度、前期降雨量4个因子。分析结果表明,降雨对坡面面蚀的制约关系十分明显。影响面蚀量的主要降雨因子是降雨量和平均降雨强度,面蚀量与降雨量和平均降雨强度呈现极显著和显著的正相关关系,面蚀量与降雨因子中的前期降雨量呈现一定的负相关关系。采用强迫引入法,建立了面蚀量与降雨因子主成分的回归方程。     

澜沧江典型对比流域水力侵蚀快速调查与评价

根据水力侵蚀面蚀和沟蚀两种不同侵蚀形态发生过程尺度空间大小不一的侵蚀特点,确定了研究区面蚀和沟蚀的不同调查评价方法.面蚀的发生过程空间尺度小,选用小区调查方法进行,而沟蚀的发生过程尺度空间大,在典型调查小流域尺度进行全面调查.然后在两种尺度下,分析形成沟蚀和面蚀的影响因素,进行沟蚀程度和面蚀强度分级,并把研究成果展延到澜沧江凤庆河流域和晓街河流域.最后,以在典型调查小流域的研究结果为对照判别依据,判断风庆河和晓街河流域的土壤侵蚀状况.结果显示,澜沧江典型流域的面蚀强度差异不大,沟蚀是造成不同流域土壤侵蚀和沟道输沙差异的主要水力侵蚀形式.     

Fault induced permanent ground deformations: Experimental verification of wet and dry soil, numerical findings’ relation to field observations of tunnel damage and implications for design

Few building codes contains provisions fault surface ruptures and accompanying soil deformations which constitutes a great risk to human lives, buildings and infrastructure. A numerical and experimental comparison show a fair agreement of result. Analysis of “real” scale show the how water increases the incompressibility of wet soil causing shear deformations to become larger and conjugate ruptures to appear for reverse faults. Field observations and numerical analysis indicates that horizontal compression of soil surrounding underground structures should be taken into account in design.     

Effect of surface stress on magneto-elastic surface waves in finitely conducting media

This paper deals with the investigation of the effect of surface stress and conductivity on the propagation of surface wave in isotropic, homogeneous, elastic media under the action of a primary magnetic field. Formulation of the general surface wave propagation problem has been made, and the corresponding frequency equation has been derived. Frequency equations for Rayleigh wave, surface shear wave and Stoneley wave have been deduced from that of general surface wave as special cases. The effects of surface stress and magnetic field on the wave velocities and attenuation factors of Rayleigh wave and surface shear wave are shown by numerical calculations and graphs. Some important wave velocity equations, as obtained by other authors, have been deduced as special cases from the wave velocity equation for Stoneley wave. It is found that the combined effect of surface stress and magnetic field modulates the wave velocity ratios and attenuation factors of Rayleigh wave and surface shear wave to a considerable extent.     

Experimental study of surface texture and resonance mechanism of booming sand

The sound-producing mechanism of booming sand has long been a pending problem in the blown sand physics. Based on the earlier researches, the authors collected some silent sand samples from Teng- ger Desert, Australian Desert, Kuwait Desert, beaches of Hainan Island and Japanese coast as well as the soundless booming sand samples from the Mingsha Mountain in Dunhuang to make washing ex- periments. In the meantime the chemical corrosion experiment of glass micro-spheres, surface coating experiment and SEM examination were also conducted. The experimental results show that the sound production of booming sand seems to have nothing to do with the presence of SiO2 gel on the surface of sand grains and unrelated to the surface chemical composition of sand grains but is related to the resonance cavities formed by porous (pit-like) physical structure resulting from a number of factors such as wind erosion, water erosion, chemical corrosion and SiO2 gel deposition, etc. Its resonance mechanism is similar to that of Hemholz resonance cavity. Under the action of external forces, nu- merous spherical and sand grains with smooth surface and porous surface are set in motion and rub with each other to produce extremely weak vibration sound and then become audible sound by human ears through the magnification of surface cavity resonance. However the booming sands may lose their resonance mechanism and become silent sand due to the damping action caused by the invasion of finer particles such as dust and clay into surface holes of sand grains. Therefore, clearing away fine pollutants on the quartz grain surface is an effective way to make silent sand emit audible sound.     

Evolution of the variability of surface temperature and vegetation density in the great plains

This study focuses on how the variability of land surface temperature and vegetation density at the SGP ARM-CART site changes over episodic (day to day) and seasonal time scales using AVHRR satellite data. Four drying periods throughout the year are analyzed. Land surface temperature had an erratic relationship with time exhibiting no deterministic pattern from day-to-day or season-to-season. Furthermore, it did not exhibit spatial pattern persistence. On the other hand, vegetation density had a consistent spatial pattern and temporal decay during average length drying periods (less than 7 days) as well as within a season. However, there were distinct differences in the seasonal pattern of variation between winter and growing seasons. In addition, the paper highlights a methodology to quantify the relationships that exist at the land surface between the primary parameter of interest and the controlling variables.     

Wind erosion of blanket peat during a short period of surface desiccation (North Pennines,Northern England)

Strong winds are a characteristic feature of UK upland areas. Despite this, understanding of aeolian processes in upland environments of the UK is limited. This paper presents direct measurements and observations of blanket peat erosion by wind action during a two week period of desiccation in the North Pennines, Northern England. A circular configuration of mass flux sediment samplers was used to collect peat eroded by wind action from 16 cardinal compass directions. Meteorological conditions (wind speed, wind direction, precipitation and temperature) were recorded by an automatic weather station set up adjacent to the site. Surface desiccation led to peat crust erosion and dust deflation. During short (≤1 hour) periods of precipitation, wind‐driven rainfall also caused erosion. Typically, dust flux rates were up to two orders of magnitude lower than recorded during periods of sustained wet weather. Measurements demonstrate the hitherto unreported rapid switch in process regime between wind‐driven rainfall and dry blow deflation in blanket peat environments. Dry blow processes of blanket peat erosion may become more important in UK upland areas if climate change promotes more frequent surface desiccation. Copyright © 2006 John Wiley & Sons, Ltd.     

The effect of interpolation methods in surface definition: an experimental study

Mappings of the earth surface and their representation in 3D (three‐dimensional) models are commonly used in most recent research. Modeling research, which starts with classical surveying methods, acquires new dimensions matching the modern technologies. 3D models of any object or earth surface can be used in much visual and scientific research. A digital model of the landscape is an important part within creation of geo‐information systems used in the public administration and in the commercial sphere. It is an important tool in applications such as geomorphology, hydrology, geology, cartography, ecology, mining etc. Values of volume in terrains that do not have regular geometric structure can be obtained more accurately by using 3D models of surfaces with respect to developing technology. Basic data of 3D models must indicate 3D coordinates of the surveyed object in the reference frame. Distribution and intensity of points are important factors in modeling earth surfaces. A minimum number of points is desired in defining an object in 3D. Interpolation methods employing different mathematical models are used to obtain 3D models of terrain surfaces. In this study, the effect of interpolation methods in defining a terrain surface is investigated. For this purpose, a uniform surface, hill‐shaped artificial object with a known volume is employed. The 3D surface and volume are calculated by using 12 different interpolation methods. Point distribution, point intensity and accuracy of point measurements are not considered. The same data set was used for all the interpolation methods. The interpolation methods are compared and evaluated based on the results. Copyright © 2007 John Wiley & Sons, Ltd.     

矢量GIS数据位置精度评价

论述了采用野外测量法评价矢量GIS数据位置精度的过程，为精确评价位置精度提出了相应的质量控制措施，讨论了必要的检测点数目、检测点选择等，并对该方法的适用范围作了说明。