Stress and deformation of offshore piles under structural and wave loading

Various offshore structures, especially large structures such as Tension Leg Platforms (TLP), are usually supported by concrete piles as the foundation elements. The stress distribution within such a large structure is a dominant factor in the design procedure of an offshore pile. To provide a more accurate and effective design for offshore foundation systems under axial and lateral wave loads, a finite element model is employed herein to determine the stresses and displacements in a concrete pile under similar loading conditions. A parametric study is also performed to examine the effects of the stress distribution due to the changing loading conditions.     

Experimental Investigation into the performance of the Axial-Flow-Type Waterjet according to the Variation of Impeller Tip Clearance

The tip clearance inside the duct from the tip of the impeller is very important to the performance of waterjet systems, which fact has been proven in the pump field. The tip clearance is especially important on the model scale because it is very difficult in manufacture to keep the tip clearance constant and minimally small along the inside of the duct. In the present study, a flush-type waterjet propulsion unit (duct, impeller, stator, and nozzle) was designed for an amphibious tracked vehicle. Two impellers of different inner diameter were designed and manufactured in order to investigate the gap effect. Resistance and self-propulsion tests with a 1/5-scale model were conducted in PNU towing tank. The flow rate at the nozzle exit, the static pressure at the various sections along the duct and also the nozzle, the revolution of the impeller, and the torque, thrust, and towing forces at various advanced speeds were measured. Based on these measurements, the performance was analyzed according to the ITTC 96 standard analysis method. Based on this analysis method, the full-scale effective and delivered power of the tracked vehicle was estimated according to the variation of tip clearance.     

Use of an optical oxygen sensor to measure dissolved oxygen in seawater

The use of an optical oxygen sensor to measure dissolved oxygen in seawater was investigated. The sensor is based on the dynamic quenching of an oxygen-sensitive fluorochrome embedded in the tip. Dissolved oxygen in seawater samples collected from eight stations at depths ranging from 3000 to 6000 m was analyzed both with the optical sensor and by the Winkler titration method. The two sets of data did not differ significantly. The stability and simplicity of the method and the good agreement of the results with those of the titration method indicate that the sensor would be useful for fieldwork.     

陀螺经纬仪的读数方法比较研究

介绍了陀螺定向测量中三种不同的数据采集方法，分析了各种方法的优缺点。作者认为传感器采集数据自动化程度高，精度高，特别是运用位置敏感探测器（PSD）采样数据量大，具有一定的抗干扰能力，但在运用传感器采样时必须注意克服非线性误差。     

赤道西太平洋大气边界层的诊断分析

利用１９９３年ＥＮＳＯ事件爆发（４月）前酝酿时期“热带大洋与全球大气－海洋耦合响应试验”强化观测阶段“向阳红五号”科学考察船１５５°Ｅ，２°Ｓ定点海洋气象和高空大气探测资料，分析了赤道西太平洋大气边界层特征。结果表明：赤道西太平洋上空辐合对流区边界层内也有等温或逆温层存在，大气边界层物理参数变化与大尺度海－气变异有密切关系，赤道太平洋沃克环流加强、东移，边界层上部逆温层出现概率明显增大，边界层内高湿层湿度减小。另外，边界层内实测风速、风向廓线随高度的变化基本上不服从Ｅｋｍａｎ规律，但由其平均，分量合成得到的平均风随高度的变化却基本符合Ｅｋｍａｎ规律。     

Study on the characteristics of the marine boundary layer in the Equatorial Pacific

ＳｔｕｄｙｏｎｔｈｅｃｈａｒａｃｔｅｒｉｓｔｉｃｓｏｆｔｈｅｍａｒｉｎｅｂｏｕｎｄａｒｙｌａｙｅｒｉｎｔｈｅＥｑｕａｔｏｒｉａｌＰａｃｉｆｉｃ￥ＺｈａｎｇＺｉｙｕａｎｄＺｈｏｕＭｉｎｇｙｕ（ＲｅｃｅｉｖｅｄＡｕｇｕｓｔ２１，１９９３；ａｃｃｅｐｔｅｄ...     

Second-Order Wave Diffraction Around 3-D Bodies by A Time-Domain Method

A time-domain method is applied to simulate nonlinear wave diffraction around a surface piercing 3-D arbitrary body. The method involves the application of Taylor series expansions and the use of perturbation procedure to establish the corresponding boundary value problems with respect to a time-independent fluid domain. A boundary element method based on B-spline expansion is used to calculate the wave field at each time step, and the free surface boundary condition is satisfied to the second order of wave steepness by a numerical integration in time. An artificial damping layer is adopted on the free surface for the removal of wave reflection from the outer boundary. As an illustration, the method is used to compute the second-order wave forces and run-up on a surface-piercing circular cylinder. The present method is found to be accurate, computationally efficient, and numerically stable.     

卫星高度计海上定标场及定标方法研究进展

介绍了卫星高度计定标中海面高度和后向散射系数的定标方法。在后向散射系数的定标中介绍了利用有源定标器和微波辐射计定标两种方法。结合卫星高度计的特点,提出了海上定标场选取所需注意的问题,并介绍了目前比较成功的几个定标场及其定标结果,旨在为我国今后发射的卫星高度计绝对定标和定标场的选取提供依据。     

等高线自动绘制中断层处理的新方法

提出了一种断层处理新方法——分块法与断层恢复法合成算法，这种方法兼有分块法与断层恢复法的优点同时又克服了其不足，较好地解决了含逆断层时煤层底板等高线自动绘制及任意边界的构网问题，使绘出的等值线图误差较小，更加符合实际。