东亚岛弧地形横剖面与板块运动

通过对东亚岛弧横剖面形态的系统分析，并结合弧前的构造应力的分析，作者认为，东亚岛弧形成于板块东移的构造环境中，横剖面形态存在两种基本类型即内缓外陡型和内陡外缓型，这两种不同的横剖面具有不同的弧前应力，前者表现弧前挤压，后者表现弧前引张，这反映地貌形态与构造应力之间的密切关系。     

Regression Formulations for the Stress at Hot Spot of Multiplanar Tubular DT Joints

- Stress concentration analysis of multiplanar tubular DT joints plays an important role in the fatigue design of offshore platforms. A semi-analytic method for stress analysis under the condition of any loads is briefly introduced in the paper. Nineteen multiplanar tubular DT joints with one of two braces of the same dimension subjected to axial loads and out- of- plane bending moments are computed for parametric stress analysis by using the present method. The influence of geometrical parameters on the stresses of multiplanar tubular DT joints is discussed and compared with corresponding uniplanar T joints. The regression formulae for the stress at hot spot of multiplanar DT joints are found by modification of SCF of corresponding uniplanar T joints. The parametric formulae for the maximum stress by superposition. Finally, the influences of stiffening effect and load-interaction effect on the maximum stress of DT joints are discussed.     

用含氯化镉培养液培养塔胞藻的生物学效应

在塔胞藻培养液中加入不同浓度的CdCl2,然后分析了培养在各种处理和对照组的塔胞藻后代.结果发现,随着镉离子浓度的升高,细胞的生长繁殖量和体积在前2轮(9d为一轮)培养中均明显降低,而在第3轮培养时,细胞的繁殖和大小接近常态.随后对处理后多种细胞内含物含量进行了分析,显示出:随着培养液中镉离子浓度增高,细胞内的蛋白质、叶绿素含量均明显下降,而可溶性糖、核酸的含量与对照相比变化不大.     

牙鲆鱼苗长途运输技术的试验研究

本实验对10个批次，总数为19047尾的不同规格和产地的牙鲆鱼苗长途运输效果进行了研究。结果表明，规格为9-12cm的鱼苗，在水温6－12℃，运输时间为35－50h，采用空运和低温活水车运输，运输死亡率为664尾，死亡率为3.39%，低温活水车短途运输是可行的，尽管长途车运方式成本较低，但由于应激强度较大，对鱼苗的生长性能影响较为严重，驯养10d累计死亡率最高达18.1%，这种模式不可取。低温（6℃）、小规格（9cm)的空运较适合牙鲆鱼苗长途运输。此外，本文还就运输应激反应、预防措施和药物防治进行详细的讨论。     

An Experi mental Study on Wave-Induced Dynamic Stresses in Seabed

1 .IntroductionEvery year ,Taiwanis subjectedtotwo or three typhoonintrusions in average which always causedisasters . Most of the disasters which occur around the coastal zone are due to seabed instability andcoastal structure destruction caused bytyphoo…     

Nonlinear Static Finite Element Stress Analysis of Pipe-in-Pipe Risers

Owing to the complexity of the pipe-in-pipe (PIP) riser system in structure, load and restraint, many problems arise in the structural analysis of the system. This paper presents a new method for nonlinear static finite element stress analysis of the PIP riser system. The finite element (FE) model of the PIP riser system is built via software AutoPIPE 6.1. According to the specialties of a variety of components in the PIP riser system, different elements are used so as to model the system accurately. Allowing for the complication in modeling the effects of seabed restraint, a technique based on the bilinear spring concept is developed to calculate the soil properties. Then, based on a pipeline project, the entire procedure of stress analysis is discussed in detail, including creation of an FE model, processing of input data and analysis of results. A wide range of loading schemes is investigated to ascertain that the stresses remain within the acceptable range of the pipe material strength. Finally, the effects of the location of flanges, the thermal expansion of submarine pipelines and the seabed restraint on stress distribution in the riser and expansion loop are studied, which are valuable for pipeline designers.     

旧路改建高速公路中地基强夯效应测试与工艺参数分析

旧路改建高速公路遇到的最主要的问题是地基的不均匀沉降。数值分析表明,对新的天然地基进行处理是解决这一问题的关键。强夯是加固地基的一种有效措施,为了对强夯工艺参数进行优化研究,对夯锤冲击地面过程中产生的动孔隙水压力、动土应力以及夯后超静孔隙水压力的消散过程进行了跟踪测试与分析。结果表明,对以风化料为主的地基,最大夯击数不宜超过4击,而且铺底夯完成2d后就可进行满夯。