双锚固段新型锚索锚固性能研究及工程应用

为探究高路堤、深路堑边坡锚固系统耐久性以及锚固效果,研制了一种内外双锚固段新型锚索,从其结构设计、结构特点及锚固机理入手,分析其受力模式与计算方法,并通过室内足尺模型试验分析双锚固段新型锚索锚固效果,试验结果表明,（1）外锚固段有效的起到了双重锚固作用;（2）双锚固段锚索系统能有效避免因锚索失效导致的预应力损失;（3）整个锚固系统能实现反向自锁功能,与传统的锚索比,安全可靠性更高,能有效避免因锚索破坏突发灾难性的安全事故,长期性价比高;（4）工程实例验证石炭系岩关组砂岩、泥岩及深灰色灰岩呈互层地层外固段长度不少于8 m,才能有效地避免外锚头失效自由段预应力不损失。试验结果对正确分析双锚固段新型锚索加固作用机制和工程设计应用具有一定的参考价值。     

煤岩水力压裂裂缝扩展形态试验研究

通过室内水力压裂物理模拟试验系统,对大尺寸原煤进行了水力压裂模拟试验,根据水力裂缝的空间展布形态分析了煤岩储层水力裂缝的延伸规律,揭示了网状裂缝的形成机制。结果表明：水力裂缝易在弱层理处分叉和转向,发育的层理和裂缝系统等结构面为压裂形成裂缝网络提供了前提条件。泵压曲线呈现出的频繁波动是煤岩内产生网状裂缝的一个显著特征。水力裂缝的起裂与延伸有4种基本模式,裂缝网络的形成多为这4种基本模式的组合。地应力差异系数和泵注排量对煤层水力裂缝形态有较大影响。较小的地应力差异系数更利于网状裂缝的形成;较高的压裂液排量易形成相对简单的裂缝形态,导致压裂改造效果较差。该试验方法和试验结果可为现场水力压裂参数设计和优化提供参考和依据。     

基于MatDEM的砂土侧限压缩试验离散元模拟研究

离散元法基于非连续介质力学理论,尤其适用于砂土等离散介质体的数值模拟研究。利用岩土体离散元模拟软件MatDEM的二次开发功能,研发了砂土侧限压缩试验三维离散元模拟器。对三个不同级配砂土试样进行了侧限压缩试验,并且进行了与之相对应的数值模拟,通过分析对比试验结果与数值模拟结果验证了所开发模拟器的有效性。模拟结果表明:离散元法可以很好地反应砂土压缩过程中的配位数变化;每个模拟样品中,粒径较小的单元受到较大的平均压力,导致平均位移较大;数值计算结果的主要误差是由离散元颗粒自身的泊松比引起的。研究突破了常规土力学研究方法的局限性,为今后岩土工程离散元模拟研究提供了参考。      

修正剑桥模型在DPC桩—土结构层中的应用分析

针对DPC桩-土结构层开展大型直剪试验,基于试验分析,在考虑DPC桩-土结构层注浆影响上引入临界应力比,构建了可描述应变软化的修正剑桥模型应力应变方程。直剪试验表明DPC桩-土结构层剪切特性表现为剪切软化,具有明显的峰值强度和残余强度,呈现出明显的结构性,其特征与超固结的黏土的剪切应力应变曲线特性类似。推导出的修正剑桥模型能较好的解释实验结果,所得出的结论对DPC桩的设计有一定的指导意义。      

连云港海相软土不排水强度特征

连云港地区软土为碱性环境下沉积的非均质海积软土,软土抗剪强度具有固有各向异性。采用三轴不固结不排水剪切（UU）试验、无侧限抗压强度（UTC）试验、快剪试验和原位十字板剪切（FVT）试验4种方法,对连云港地区软土的不固结不排水抗剪强度特征进行了研究。结果表明：土体水平剪切面强度最低,竖直面抗剪强度最高;土体制样采用垂直方向的切取试样方式时,土体强度最高。根据三轴UU试验得出的黏聚强度和内摩擦角基于土体单元极限平衡理论恢复了土体剪切破坏时的应力状态,计算出土体实际抗剪强度。三轴UU试验得出的抗剪强度平均值约为13.13 kPa,试样破裂面与水平面的夹角在45.1°~45.7°区间最为集中。UTC试验测得的土体平均抗剪强度近似等于三轴UU试验测得的平均抗剪强度。FVT试验测得软土抗剪强度平均值为19.72 kPa,与三轴UU试验和UTC试验得出的抗剪强度平均值相比高了约6.60 kPa,这种现象与室内试验试样的机械扰动、土体应力状态改变和剪切面特征有关。     

畸形波作用下双层水平板防波堤压力分布特性研究

基于物理模型试验,考虑畸形波参数、相对板宽、相对波高等影响因素,就畸形波对平顶双层水平板防波堤作用进行研究。首先对畸形波作用下双层水平板的波浪力分布特征进行了讨论,然后就最大波动压强、结构最大总垂向力与不规则波作用进行了对比分析。结果表明,畸形波作用下,双层水平板最大波动压力出现在前端迎浪区域附近,向尾端逐渐递减。双层水平板4个受力面的压力分布不同且有相位差,4个受力面的最大波动压力时间差约在0.1T_p~0.4T_p范围内变化。与不规则波作用比较,畸形波作用没有显著改变波压包络分布特征,但增大了波压包络强度值。试验范围内,就最大总力而言,两者最大总浮托力比值在1.06~2.45间变化;向下的最大总垂向力比值在1.22~2.07之间变化;就波动压力而言,其增大的幅度与畸形波参数α₁相关性最强,随α₁的增大而增大,在α₁=2.04~3.1试验范围内,畸形波作用时的最大压强比不规则波作用时可约增大20%~80%。就最大波吸力而言,两者的比值与畸形波参数α₄相关性最强,随α₄的增大而减小。在α₄=0.62~0.75试验范围内,最大波吸力强度的比值在1.61~0.87范围内变化。当α₄≤0.72时,畸形波作用时的最大波吸力大于不规则波作用时的最大波吸力;当α₄ > 0.72时则刚好相反。     

伶仃洋河口泥沙絮凝特征及影响因素研究

泥沙絮凝对河口细颗粒泥沙运动过程起着极其重要的作用。本文通过LISST-100激光粒度仪等仪器实测伶仃洋河口2013年洪季悬浮泥沙絮凝体现场粒径及水动力、泥沙条件,结合实验室悬沙粒径分析,研究大小潮期间伶仃洋河口泥沙絮凝特征,探讨紊动剪切强度、含沙量、盐度分层及波浪等因素对伶仃洋河口泥沙絮凝的影响。结果表明:伶仃洋河口水体中现场粒径平均值为148.53 μm,大于实验室悬沙分散粒径36.74 μm,河口絮凝现象明显;沉速与有效密度、粒径呈正相关,絮团平均有效密度为153.49 kg/m3,平均沉速达1.13 mm/s;小潮时絮团平均粒径大于大潮,垂向上表底层絮团粒径小、中层大,中底层絮团沉速大于表层。伶仃洋河口水动力、泥沙条件是影响其泥沙絮凝的重要因素,低剪切强度（小于5 s-1）、低含沙量（小于50 mg/L）及高体积浓度有利于细颗粒泥沙之间的相互碰撞,促进絮凝作用;当剪切强度与颗粒间碰撞强度高于絮团所能承受的强度时,絮团易破碎分解成小絮团或更细的泥沙颗粒;伶仃洋河口盐度层化引起的泥沙捕获现象增大中层泥沙体积浓度,有利于中层絮凝体的发育;观测期相对较大的波浪增强水体紊动,增大了水体细颗粒泥沙的碰撞几率,表层絮团粒径随波高峰值的出现而增大。     

Experimental and numerical study on vortex-induced motions of a deep-draft semi-submersible

An experimental study on vortex-induced motions (VIM) of a deep-draft semi-submersible (DDS) was carried out in a towing tank, with the aim to investigate the VIM effects on the overall hydrodynamics of the structure. In order to study the fluid physics associated with VIM of the DDS, a comprehensive numerical simulation was conducted to examine the characteristics of vortex shedding processes and their interactions due to multiple cylindrical columns. The experimental measurements were obtained for horizontal plane motions including transverse, in-line and yaw motions as well as drag and lift forces on the structure. Spectral analysis was further carried out based on the recorded force time history. These data were subsequently used to validate the numerical model. Detailed numerical results on the vortex flow characteristics revealed that during the “lock-in”, the vortex shedding processes of the upstream columns enhance the vortex shedding processes of the downstream columns leading to the rapid increase of the magnitude of VIM. In addition to the experimental measurements, for the two uniform flow incidences (0° and 45°) investigated, comprehensive numerical data of the parametric study on the VIM characteristics at a wide range of current strength will also serve as quality benchmarks for future study and provide guidance for practical design.     

Effect of Silica Fume on Compressive Strength of Oil-Polluted Concrete in Different Marine Environments

In the present research, effect of silica fume as an additive and oil polluted sands as aggregates on compressive strength of concrete were investigated experimentally. The amount of oil in the designed mixtures was assumed to be constant and equal to 2% of the sand weight. Silica fume accounting for 10%, 15% and 20% of the weight is added to the designed mixture. After preparation and curing, concrete specimens were placed into the three different conditions: fresh, brackish and saltwater environments (submerged in fresh water, alternation of exposed in air & submerged in sea water and submerged in sea water). The result of compressive strength tests shows that the compressive strength of the specimens consisting of silica fume increases significantly in comparison with the control specimens in all three environments. The compressive strength of the concrete with 15% silica fume content was about 30% to 50% higher than that of control specimens in all tested environments under the condition of using polluted aggregates in the designed mixture.     

Laboratory study on cement admixed marine silt bricks

For the purpose of efficient utilization of sediments dredged from harbor, a new method was proposed in this study. Marine silt bricks were made by mixing sediments with cement and gypsum, placing it in a cubic mold with 240 mm in length, 115 mm in width, and 53 mm in height, and curing for certain days. To investigate the effects of cement and initial water content of soil on the mechanical behavior of marine silt bricks, unconfined compressive and flexural strength tests were carried out. Given the same curing time and cement content, the higher the initial water content, the lower the compressive and flexural strength. After 60 days of curing, the compressive strength of marine silt bricks with cement content = 20% and water content = LL (liquid limit) reached approximately 5 MPa. The flexural strength was relatively low. The flexural strength of marine silt bricks with 20% cement and water content = LL was around 1.5 MPa. The compressive and flexural strength decreased with the increase of water/cement ratio. As for the curing time, longer curing time had a positive impact on the compressive strength. The ratio of flexural to compressive strength varied slightly in the range of 0.4–0.5.