水槽试验浪成沙纹的特征及控制因素

在水槽中利用周期（１．０～１．９ｓ）、波高（８．６～１１．７ｃｍ）不同的规则波及波群塑造了沙纹。试验指出；１、沙纹的垂向形态指数及对称性指数符合标准浪成沙纹的相应值；２、沙纹的波长、波高、陡度与波浪水质点近底床水平运动方向的轨迹直径、波浪流的无量纲切应力、沉积物的活动性参数呈函数关系；３、沙纹的对称性与波浪的底部质量输移速率和水质点近底床的水平方向运动速率的比值有关。     

An empirical model for the development and equilibrium morphology of current ripples in fine sand

A flume study on the development and equilibrium morphology of current ripples in fine sand (D₅₀ = 0·238 mm) was performed to extend an empirical model for current ripple stability in 0·095 mm sand to larger grain sizes. The results of the flume experiments agree with the very fine sand model that current ripple development from a flat bed is largely independent of flow velocity. At all flow velocities, ripples evolve from incipient, through straight, sinuous and non-equilibrium linguoid, to equilibrium linguoid plan morphology. The time needed to achieve an equilibrium linguoid plan form is related to an inverse power of flow velocity and ranges from several minutes to more than hundreds of hours. Average equilibrium height and length are 17·0 mm and 141·1 mm respectively. These values are about 20% larger than in very fine sand. Equilibrium ripple height and length are proportional to flow velocity near the stability field of dunes. In the same velocity range, a characteristic grouping of ripples with smaller ripples migrating on the upstream face of larger ripples was observed. Bed-form development shows a conspicuous two-phase behaviour at flow velocities < 0·49 m s^?1. In the first phase of development, ripple height and length increase along an exponential path, similar to that at higher flow velocities, thus reaching intermediate equilibrium values of 14·8 mm and 124·5 mm respectively. After some time, however, a second phase commences, that involves a rapid increase in bed-form size to the typical equilibrium values for 0·238 mm sand. A comparison with literature data shows that the results obtained for 0·238 mm sand agree reasonably well with other flume studies at similar grain size. Yet considerable variability in the relationships between ripple dimensions and flow strength ensues from, among others, underestimation of equilibrium time, shallow flow depths and differences in sediment texture.     

The dynamics of turbulent, transitional and laminar clay-laden flow over a fixed current ripple

Most aqueous sedimentary environments contain varying concentrations of fine‐grained, often clay‐rich, sediment that is transported in suspension and may modify the properties of the flow and underlying mobile bed. This paper presents results from a series of laboratory experiments examining the mean and turbulent properties of clay‐laden (kaolinite) flows, of various volumetric sediment concentrations between 0·046% and 12·7%, moving over a fixed, idealized current ripple. As the kaolinite concentration was raised, with flow velocity and depth constant, four flow types were observed to occur: (i) turbulent flow, in which flow separation is dominant in the leeside of the ripple; (ii) turbulence‐enhanced transitional flow, in which turbulence in the leeside separation zone region is enhanced; (iii) turbulence‐attenuated transitional flow, in which turbulence along the separation zone shear layer and in the free flow above it becomes damped, eventually leading to a reduction in the size of the separation zone wake region; and (iv) laminar plug flow, in which turbulence is damped and flow is almost stagnant in the lee of the ripple. Such modulation of turbulence by increasing clay concentrations suggests that many paradigms of flow and bedform dynamics, which have been based on extensive past work in clear water flows, require revision. The present results highlight a need to fully characterize the boundary conditions for turbulence modulation as a function of clay type and applied flow conditions, and the effects of such flows on fully mobile cohesionless beds.     

Origin,evolution and anatomy of silt‐prone submarine external levées

Submarine external levées are constructional features that develop outside slope channel systems, and are a volumetrically significant component of continental margins. However, detailed observations of their process sedimentology and depositional architecture are rare. Extensive exposures of external levées at multiple stratigraphic intervals and well‐constrained palaeogeographic positions in the Fort Brown Formation, Karoo Basin, South Africa, have been calibrated with research boreholes. This integrated data set permits their origin, evolution and anatomy to be considered, including high‐resolution analysis of sedimentary facies distribution and characterization of depositional sub‐environments. An idealized model of the stratigraphic evolution and depositional architecture of external levées is presented, and variations can be attributed to allogenic (for example, sediment supply) and autogenic (for example, channel migration) factors. Initiation of external levée construction is commonly marked by deposition of a basal sand‐rich facies with sedimentary structures indicating rapid deposition from unconfined flows. These deposits are interpreted as frontal lobes. Propagation of the parent channel, and resultant flow confinement, lead to partial erosion of the frontal lobe and development of constructional relief (levées) by flow overspill and flow stripping. Overall fining‐upwards and thinning‐upwards profiles reflect increased flow confinement and/or waning flow magnitude through time. Identification of a hierarchy of levée elements is not possible due to the absence of internal bounding surfaces or sharp facies changes. The down‐slope taper in levée height and increasing channel sinuosity results in increasing numbers of crevasse lobe deposits, and is reflected by the increased occurrences of channel avulsion events down‐dip. External levées from the Fort Brown Formation are silt‐rich; however their stratigraphic evolution and the distribution of many components (such as sediment waves and crevasse lobe) share commonalities with mud‐rich external levées. This unique integrated data set has permitted the first high‐resolution characterization of external submarine levée systems.     

On the transition between 2D and 3D dunes

Sediment transport in sand-bedded alluvial channels is strongly conditioned by bedforms, the planimetric morphology of which can be either two- or three-dimensional. Experiments were undertaken to examine the processes that transform the bed configuration from two-dimensional (2D) dunes to three-dimensional (3D) dunes. A narrowly graded, 500 μm size sand was subjected to a 0·15 m deep, non-varying mean flow ranging from 0·30 to 0·55 m sec⁻¹ in a 1 m wide flume. Changes in the planimetric configuration of the bed were monitored using a high-resolution video camera that produced a series of 10 sec time-lapsed digital images. Image analysis was used to define a critical value of the non-dimensional span (sinuosity) of the bedform crestlines that divides 2D forms from 3D forms. Significant variation in the non-dimensional span is observed that cannot be linked to properties of the flow or bedforms and thus appears random. Images also reveal that, once 2D bedforms are established, minor, transient excesses or deficiencies of sand are passed from one bedform to another. The bedform field appears capable of absorbing a small number of such defects but, as the number grows with time, the resulting morphological perturbations produce a transition in bed state to 3D forms that continue to evolve, but are pattern-stable. The 3D pattern is maintained by the constant rearrangement of crestlines through lobe extension and starving downstream bedforms of sediment, which leads to bifurcation. The experiments demonstrate that 2D bedforms are not stable in this calibre sand and call into question the reliability of bedform phase diagrams that use crestline shape as a discriminator.     

Climbing‐ripple successions in turbidite systems: depositional environments,sedimentation rates and accumulation times

Climbing‐ripple cross‐lamination is most commonly deposited by turbidity currents when suspended load fallout and bedload transport occur contemporaneously. The angle of ripple climb reflects the ratio of suspended load fallout and bedload sedimentation rates, allowing for the calculation of the flow properties and durations of turbidity currents. Three areas exhibiting thick (>50 m) sections of deep‐water climbing‐ripple cross‐lamination deposits are the focus of this study: (i) the Miocene upper Mount Messenger Formation in the Taranaki Basin, New Zealand; (ii) the Permian Skoorsteenberg Formation in the Tanqua depocentre of the Karoo Basin, South Africa; and (iii) the lower Pleistocene Magnolia Field in the Titan Basin, Gulf of Mexico. Facies distributions and local contextual information indicate that climbing‐ripple cross‐lamination in each area was deposited in an ‘off‐axis’ setting where flows were expanding due to loss of confinement or a decrease in slope gradient. The resultant reduction in flow thickness, Reynolds number, shear stress and capacity promoted suspension fallout and thus climbing‐ripple cross‐lamination formation. Climbing‐ripple cross‐lamination in the New Zealand study area was deposited both outside of and within channels at an inferred break in slope, where flows were decelerating and expanding. In the South Africa study area, climbing‐ripple cross‐lamination was deposited due to a loss of flow confinement. In the Magnolia study area, an abrupt decrease in gradient near a basin sill caused flow deceleration and climbing‐ripple cross‐lamination deposition in off‐axis settings. Sedimentation rate and accumulation time were calculated for 44 climbing‐ripple cross‐lamination sedimentation units from the three areas using TDURE, a mathematical model developed by Baas et al. (2000) . For T_c divisions and T_bc beds averaging 26 cm and 37 cm thick, respectively, average climbing‐ripple cross‐lamination and whole bed sedimentation rates were 0·15 mm sec^?1 and 0·26 mm sec^?1 and average accumulation times were 27 min and 35 min, respectively. In some instances, distinct stratigraphic trends of sedimentation rate give insight into the evolution of the depositional environment. Climbing‐ripple cross‐lamination in the three study areas is developed in very fine‐grained to fine‐grained sand, suggesting a grain size dependence on turbidite climbing‐ripple cross‐lamination formation. Indeed, the calculated sedimentation rates correlate well with the rate of sedimentation due to hindered settling of very fine‐grained and fine‐grained sand–water suspensions at concentrations of up to 20% and 2·5%, respectively. For coarser grains, hindered settling rates at all concentrations are much too high to form climbing‐ripple cross‐lamination, resulting in the formation of massive/structureless S₃ or T_a divisions.     

2DV modelling of sediment transport processes over full-scale ripples in regular asymmetric oscillatory flow

Wave-induced, steep vortex ripples are ubiquitous features in shallow coastal seas and it is therefore important to fully understand and model the sediment transport processes that occur over them. To this end, two two-dimensional vertical (2DV) models have been critically tested against detailed velocity and sediment concentration measurements above mobile ripples in regular asymmetric oscillatory flow. The two models are a k–ω turbulence-closure model and a discrete-vortex, particle-tracking (DVPT) model, while the data are obtained in the Aberdeen oscillatory flow tunnel (AOFT). The models and the data demonstrate that the time-dependent velocity and suspended sediment concentration above the ripple are dominated by the generation of lee-side vortices and their subsequent ejection at flow reversal. The DVPT model predicts the positions and strengths of the vortices reasonably well, but tends to overpredict the velocity close to the ripple surface. The k–ω model, on the other hand, underpredicts the height to which the vortices are lifted, but is better able to predict the velocity close to the bed. In terms of the cycle- and ripple-averaged horizontal velocity, both models are able to reproduce the observed offshore flow close to and below the ripple crest and the DVPT model is able to produce the onshore flow higher up. In the vicinity of the vortices, the DVPT model better represents the concentration (because of its better prediction of vorticity). The k–ω model, on the other hand, better represents the concentration close to the ripple surface and higher up in the flow (because of the better representation of the near-bed flow and background turbulence). The measured and predicted cycle- and ripple-averaged suspended sediment concentrations are in reasonable agreement and demonstrate the expected region of exponential decay. The models are able to reproduce the observed offshore cycle- and ripple-averaged suspended sediment flux from the ripple troughs upwards, and as a result, produce net offshore suspended sediment transport rates that are in reasonable agreement. The net measured offshore suspended transport rate, based on the integration of fluxes, was found to be consistent with the total net offshore transport measured in the tunnel as a whole once the onshore transport resulting from ripple migration was taken into account, as would be expected. This demonstrates the importance of models being able to predict ripple-migration rates. However, at present neither of the models is able to do so.     

风沙跃移运动发展过程的离散动力学模拟

采用类似分子动力学的离散方法对二维风沙跃移过程运用高性能并行计算进行理论模拟。在本模拟模型中,考虑了沙粒与床面的碰撞、跃移沙粒与气流的相互作用等基本力学过程组成的复杂系统。通过并行运算技术使计算沙粒数达到72000的巨量计算得以实现。初步结果显示：自然跃移运动的基本特征如风沙流层内输沙率廓线可以较为成功的得以模拟。     

A wave modulation model of ripples over long surface waves

A study is presented on the modulation of ripples induced by a long surface wave (LW) and a new theoretical modulation model is proposed. In this model, the wind surface stress modulation is related to the modulation of ripple spectrum. The model results show that in the case of LW propagating in the wind direction with the wave age parameter of LW increasing, the area with enhanced shear stress shifts from the region near the LW crest on the upwind slope to the LW trough. With a smaller wave age parameter of LW, the ripple modulation has the maximum on the upwind slope in the vicinity of LW crest, while with a larger parameter the enhancement of ripple spectrum does not occur in that region. At low winds the amplitude of ripple modulation transfer function (MTF) is larger in the gravity wave range, while at moderate or high winds it changes little in the range from short gravity waves to capillary waves.