双剪统一强度准则改进及其在岩土工程中的应用

在分析Mohr-Coulomb强度准则和双剪统一强度准则的基础上,提出了主剪面应力对和主剪面应力对的作用这2个新概念,并以此为出发点,通过考虑十二面体单元主剪面上所有3个主剪面应力对的共同作用,在双剪强度准则的基础上提出了一个新准则,并对其作了极限线分析.应用该新强度准则研究了静水压力条件下圆形巷道围岩弹塑性分析和土压力计算问题.研究表明,该准则不仅能较好地非线性反映岩土的3个基本强度特征,还解决了双剪统一准则中存在的双重破坏角问题.     

Geological controls on rock mass classification of coal from Huntly East Mine, New Zealand

Rock Mass Rating (RMR) measurements from 65 sites within Huntly East underground coal mine are presented. All measurements are in coal, for which the dominant discontinuities are vertical cleat. Basic RMR values using two discontinuity spacings are presented: overall RMR based on the average spacing of all individual discontinuities; and cleat zone RMR based on the average spacing between zones of cleat. Cleat orientations are highly variable, but on average approximately parallel horizontal stress axes (face cleat follows maximum horizontal stress axis, butt cleat follows minimum horizontal stress axis).Contours of RMR variations throughout the mine are used to compare rock mass conditions with geological structure. It is apparent that: (1) RMR is least within downthrown fault blocks, and particularly immediately on the downthrown sides of faults, and greatest in upthrown fault blocks; and (2) RMR contours parallel horizontal stress axes within fault-bounded blocks, and bend to parallel faults at block boundaries. From similar contours for parameters contributing to RMR, the Rock Quality Designation (RQD), groundwater rating, and discontinuity condition rating create most of the observed variations in RMR. RQD is determined from the measured discontinuity frequency and hence is a measure of the degree of fracturing of the rock mass. This is interpreted as influencing the groundwater and condition parameters directly by allowing greater water ingress. Discontinuity frequency is greatest (least spacing) in the immediate vicinity of faults, and in downthrown fault blocks, generating low RMR values. Within fault blocks RQD varies little, so RMR contours align with cleat orientations.As RMR contours, faults, stress field and cleat orientation are clearly interrelated, there is unequivocally a connection between RMR and structural geology; this allows some predictive capacity in terms of ground conditions. If geological features can be accurately defined through either drilling programs or seismic surveys, then ground conditions may be predicted before panels are driven.     

Triaxial stress state deep in orogenic belts: an example from Turkey

A rare metachert pebble containing amphibole grains with microboudin structures in a wide range of orientations provides an opportunity to perform stress analysis in two orthogonal orientations on the foliation surface. The sample was analysed by the microboudin method to infer the triaxial stress state during microboudinage. Stress parameters proportional to the far-field differential stress were determined for sodic amphibole grains in the two orientations. The ratio of the stresses in the two orthogonal orientations (σ₁−σ₂)/(σ₁−σ₃) was calculated to be 0.64, indicating that σ₂ lies closer to the midpoint between σ₁ and σ₃ than to σ₃.     

Focal mechanism dependence of static stress triggering of earthquakes

We perform a global statistical investigation into the problem of Coulomb stress triggering of earthquakes by using the Harvard CMT catalogue of shallow earthquakes from 1976 to 2001. We consider ‘earthquake pairs’, i.e., pairs of successive earthquakes occurring near each other with similar focal mechanisms, and address the problem of whether or not the change of the Coulomb failure stress (CFS) produced by the first earthquake of the pair ‘encourages’ the occurrence of the second one. An interesting feature is that such a Coulomb stress-triggering phenomenon has an apparent focal mechanism dependence: for thrust earthquakes, a more evident triggering effect can be observed.