多因素组合影响阶段矿柱上采顶板临界厚度研究

采用散体充填法的矿山,由于充填体无法直接暴露,阶段矿柱回采临界厚度的保留成为残矿回收的突出难题。基于传统弹性梁理论,结合实际情况,将阶段矿柱简化为均布载荷下两端固定的弹性梁力学模型,推导了其弹性应力解,揭示了 是阶段矿柱上采过程的第1破坏应力。理论分析表明：影响矿柱上采顶板临界厚度的主要因素为：散体载荷、回采跨度和岩体抗拉强度。利用FLAC3D完成了多因素组合影响阶段矿柱上采过程数值模拟正交试验,分析了单一影响因素与顶板临界厚度的关系,利用多元非线性回归的数学方法,建立了上采过程三因素组合影响下阶段矿柱临界厚度数学预测公式。最终,实现了散体介质下阶段矿柱上采临界厚度的预测。结合凤凰山铜矿-240 m阶段矿柱回采实际,表明了该预测公式的适用性。     

Cyclic test of a coupled steel plate shear wall substructure

Coupled steel plate shear wall (C‐SPSW) consists of two or more steel plate shear walls interconnected by coupling beams at the floor levels. In this study, a six‐story C‐SPSW prototype building was designed. A 40% scale C‐SPSW specimen, which is representative of the bottom two‐and‐half‐story substructure of the prototype, was cyclically tested using Multi‐Axial Testing System at the National Center for Research on Earthquake Engineering in 2009. In addition to a constant vertical force representing the gravity load effects, cyclic increasing displacements and the corresponding overturning moments transmitted from the upper stories were computed online and simultaneously applied on the substructural specimen. This paper firstly introduces the designs of the prototype C‐SPSW and the test specimen. Then, the test results and the numerical simulation are discussed in detail. Test results confirm the effectiveness of the proposed column capacity design method, which aims at limiting the plastic hinge formation within the bottom quarter height of the bottom column. Test and analytical results suggest that the coupling beam rotational demands can be estimated as the design story drifts when the formation of desirable plastic mechanism of the C‐SPSW is expected. Copyright © 2011 John Wiley & Sons, Ltd.     

Tests and model calibration of high‐strength steel tubular beam‐to‐column and column‐base composite joints for moment‐resisting structures

Performance‐based engineering (PBE) methodologies allow for the design of more reliable earthquake‐resistant structures. Nonetheless, to implement PBE techniques, accurate finite element models of critical components are needed. With these objectives in mind, initially, we describe an experimental study on the seismic behaviour of both beam‐to‐column (BTC) and column‐base (CB) joints made of high‐strength steel S590 circular columns filled with concrete. These joints belonged to moment‐resisting frames (MRFs) that constituted the lateral‐force‐resisting system of an office building. BTC joints were conceived as rigid and of partial strength, whereas CB joints were designed as rigid and of full strength. Tests on a BTC joint composed of an S275 steel composite beam and high‐strength steel concrete‐filled tubes were carried out. Moreover, two seismic CB joints were tested with stiffeners welded to the base plate and anchor bolts embedded in the concrete foundation as well as where part of a column was embedded in the foundation with no stiffeners. A test programme was carried out with the aim of characterising these joints under monotonic, cyclic and random loads. Experimental results are presented by means of both force–interstory drift ratio and moment–rotation relationships. The outcomes demonstrated the adequacy of these joints to be used for MRFs of medium ductility class located in zones of moderate seismic hazard. Then, a numerical calibration of the whole joint subassemblies was successfully accomplished. Finally, non‐linear time‐history analyses performed on 2D MRFs provided useful information on the seismic behaviour of relevant MRFs. Copyright © 2015 John Wiley & Sons, Ltd.     

利用强震震源机制解资料反演中国大陆及其邻区的形变场模型

搜集了1900-2013年间发生在中国大陆及其邻区的震源机制解资料,详细整理了其中的70个7级及以上大震的震源参数、地表破裂带和地表位移资料。根据资料的完整程度将地震分成三类：A类存在地表破裂和地表位移观测资料;B类存在地表破裂资料,但缺少地表位移观测数据;C类缺少地表破裂带和地表位移观测资料。对B类和C类缺少地表位移观测数据的地震,利用三角形模型模拟其位移分布。再根据地表位移分布及地震破裂带与本文使用网格模型之间的位置关系将地震分段。最后,利用分段前、后的地震数据和改进的双三次样条方法反演研究区域的形变场模型。结果表明：①大震资料的分段处理改进了地震数据的反演结果,提高了反演模型的合理性和空间一致性;在喜马拉雅断裂带,形变场具有更好的连续性,其变形特征与地质等数据的反演结果基本吻合;塔里木盆地和阿尔金断裂的形变量减小,与该区域较低的地震活动性一致;戈壁—阿尔泰的变形从SE的挤压和ＮＥ的拉张调整到NE的挤压和NW的拉张;鄂尔多斯西缘的拉张分量明显减小。②113年的地震资料解释了印度板块向欧亚板块运动总速率的30～50%,存在20mm/a左右的速度亏损,该亏损量可能包括断层蠕动、褶皱等非震形变,未监测到或者缺失的地震,及以弹性应变能形式存在通过潜在地震释放的应变。     

系梁对桩柱式基础反射波法检测影响的计算及现场试验

根据应力波按半球面波扩展传播的特点,结合系梁(盖梁)、墩柱、桩基之间的几何尺寸关系,建立系梁(盖梁)等结构件对应力波干扰频率的计算方法并得到其分布特征。采用多通道同步采集设备结合同相轴分析方法进行桩柱式基础完整性状况跟踪测试现场试验。结果表明:桩顶自由时得到的扩径、桩底反射等信号特征可以在墩柱、系梁等施工后测试得到的信号中体现;拾振点应尽量竖向串列式排列,这种拾振方式不仅可以根据拾振点起始波峰之间的时差和拾振点间距计算结构物的应力波波速,而且不同拾振点的振动曲线能形成同相轴,便于利用同相轴分析判断桩底、盖梁(系梁)反射和其他反射体的反射。数据分析时,对异常信号应重点分析其拾取时刻,并借助测定的墩柱、系梁或盖梁的应力波波速判断其发生位置。     

横-竖立体加筋地基中附加应力的分析计算

建立了横-竖立体加筋（H-V筋）地基的有限元模型,通过分析地基中的竖向应力分布、水平向位移分布以及筋-土界面相互作用,发现横-竖立体加筋地基中的竖向应力在筋材下方出现扩散和重分布,并逐渐向土体下部传递,使得土体中整体的应力分布更加均匀;同时,横-竖筋材中的竖筋类似于一个侧壁,其提供的垂直侧向力约束了介于竖筋间的土体,限制了土体的侧向水平位移,使得地基中筋材上部土体的侧向水平位移变小。基于有限元模拟对横-竖立体加筋地基加固机制的认识,将横-竖立体筋视为作用在地基上的一维弹性地基梁,通过弹性地基梁理论,根据弗拉曼解推导求解了横-竖立体加筋地基中任意一点竖向附加应力的计算表达式。将模型计算结果与有限元模拟所得结果进行对比发现两者吻合良好。     

黏滞声波高斯束叠前深度偏移

高斯束偏移不仅具有接近于波动方程偏移的成像精度,而且保留了Kirchhoff 积分法高效、灵活的优点,可以对复杂介质准确成像。由于实际地下介质具有黏滞性,因此研究黏滞声波叠前深度偏移具有一定的现实意义。笔者采用高斯束偏移方法对地震数据进行吸收衰减补偿。首先给出共炮域高斯束叠前深度偏移原理;然后在此基础上推导补偿吸收衰减的表达式,校正品质因子Q引起的振幅衰减和相位畸变,实现基于吸收衰减补偿的高斯束叠前深度偏移;最后用两层模型和气云模型对偏移方法进行了测试。结果表明,在考虑地下介质的黏滞性时,黏滞声波高斯束叠前深度偏移比声波高斯束叠前深度偏移具有更高的成像分辨率。     

Modeling of the composite action in fully restrained beam‐to‐column connections: implications in the seismic design and collapse capacity of steel special moment frames

This paper investigates the effect of the composite action on the seismic performance of steel special moment frames (SMFs) through collapse. A rational approach is first proposed to model the hysteretic behavior of fully restrained composite beam‐to‐column connections, with reduced beam sections. Using the proposed modeling recommendations, a system‐level analytical study is performed on archetype steel buildings that utilize perimeter steel SMFs, with different heights, designed in the West‐Coast of the USA. It is shown that in average, the composite action may enhance the seismic performance of steel SMFs. However, bottom story collapse mechanisms may be triggered leading to rapid deterioration of the global strength of steel SMFs. Because of composite action, excessive panel zone shear distortion is also observed in interior joints of steel SMFs designed with strong‐column/weak‐beam ratios larger than 1.0. It is demonstrated that when steel SMFs are designed with strong‐column/weak‐beam ratios larger than 1.5, (i) bottom story collapse mechanisms are typically avoided; (ii) a tolerable probability of collapse is achieved in a return period of 50 years; and (iii) controlled panel zone yielding is achieved while reducing the required number of welded doubler plates in interior beam‐to‐column joints. Copyright © 2014 John Wiley & Sons, Ltd.     

框架式预应力锚固系统分阶段可靠性分析

将框架梁在张拉阶段或工作阶段时纵梁与横梁的破坏、梁的正截面与斜截面的破坏以及锚杆的破坏等主要失效模式视为串联系统,提出了框架预应力锚索的分阶段系统可靠性计算模型。在张拉阶段,将锚索力按照位移协调和静力平衡的原则分配在纵、横梁上,然后按Winkler弹性地基梁模型分别计算单片梁的内力;在工作阶段,将侧向土压力系数视为随机变量,框架梁视为土压力作用下的简支梁来计算其内力。基于各失效模式功能函数之间的相关系数矩阵,导出了预应力锚索框架的系统可靠性计算方法并编制了计算程序。对某工程实例的计算结果表明,预应力锚索框架的失效概率主要由纵梁在工作阶段和张拉阶段的正截面失效概率及锚杆的失效概率三者共同决定,而假设此3种失效模式相互独立的系统失效概率与考虑失效模式相关性的系统失效概率误差为8.1%。     

反倾层状岩质边坡悬臂梁极限平衡模型研究

基于悬臂梁理论和运用极限平衡法研究反倾层状岩质边坡变形破坏是一种既注重变形过程又注重力学分析的可行方法。在国内外研究现状基础上,研究悬臂梁极限平衡分析模型。首先通过野外现象的观测,提出能对反倾层状边坡变形几何空间条件进行分区的“基准面”的概念,再利用“基准面”分析岩层分区破坏模式的力学机制,认为破坏面的形成机制是弯曲拉裂和压缩剪切的共同作用结果,对悬臂梁极限平衡分析模型中的各参数确定给出假设或理论分析,建立了计算模型。以重庆市巫溪县中梁水库硝洞槽-郑家大沟库段反倾岸坡为例,在边坡变形破坏模式识别基础上,应用悬臂梁极限平衡模型理论分析实例,验证该模型的合理性,同时也给出反倾层状边坡悬臂梁极限平衡模型计算步骤,用数值模拟方法验证该分析模型的正确性。模型计算结果表明,破坏区大体分为滑移区、倾倒区和倾倒变形影响区,破坏区大小由坡角、岩层倾角、坡高共同决定,当三者关系（见式（13））大于0时,才存在破坏区,才有可能发生变形破坏。研究成果对反倾层状岩质边坡稳定性评价与防治具有理论指导意义和应用价值。