动力定位系统与单波束测深仪在科考船定点作业中的应用

科考船定点作业时会受到海洋风、涌、浪、流等外界环境因素影响，导致工作效率降低，原位测量精度下降，甚至影响作业安全。动力定位系统 （DP） 具有自动定位功能，能够抵抗外界环境因素的影响，可实现科考船高精度定点控位。 单波束测深仪不仅可以测量水深，也可反映水下设备深度信息，可以起到辅助监控水下设备功能。本文在介绍定点作业施工现状与局限性的基础上，分析 DP 系统与单波束测深仪工作原理，以“向阳红 01”船为载体，在定点作业时开启 DP 系统与单波束测深仪，发现该方法可以提高科考船定点作业工作效率、原位测量精度并保障作业安全，可为其他科考船定点作业提供参考。     

南黄海及相邻陆区松散沉积层磁性地层的研究

本文通过研究区5个钻孔松散沉积岩心磁性地层的划分对比,获知布容与松山极性带的界线,南黄海和陆区北部位于80.0—99.5m。陆区的南部此界线于270.4m深处。松山和高斯极性带的界线,海区未揭露到,其沉积起始时间都小于1.7Ma。而陆区的南、北部分别位于117m和328.2m。高斯和吉尔伯特极性带的界线,陆区北部为140m,而南部区为460.15m。沉积起始时间为3.4Ma。吉尔伯特底界仅北部陆区所揭示,为190.5m。松散沉积层与下伏白垩纪(?)石灰岩接触面位于400.35m,沉积起始时间约17.0Ma。     

Comparison of Strain-rate Dependent Stress-Strain Behavior from Ko-consolidated Compression and Extension Tests on Natural Hong Kong Marine Deposits

This article presents results from a series of K_o-consolidated compression and extension triaxial tests on specimens from undisturbed samples of Hong Kong Marine Deposits (HKMD). To investigate the strain-rate effects, a total of seven K_o-consolidated triaxial tests were conducted including four compression tests and three extension tests. After K_o-consolidation, the triaxial test specimens were sheared at step-changed axial strain rates under three different confining pressures of 50 kPa, 150 kPa, and 400 kPa, respectively. The step-changed strain rates were applied in the following order: +2%/h, +0.2%/h, +20%/h, -2%/h (unloading) and +2%/h (reloading) for the four compression tests and -2%/h, -0.2%/h, -20%/h, +2%/h (unloading) and -2%/h (reloading) for the three extension tests. The results are reported and analyzed in the paper. The results show that the strain rate effects, the stress-strain characteristics, and the effective stress paths of the specimens for tests in a compression state are different from those for tests in an extension stage. One order of magnitude increase in axial strain rate causes an average 8.6% increase in undrained shear strength for compression tests and a 12.1% increase for extension tests. It is also found that the failure mode of the specimens in compression is different from that in extension. The stress-strain behavior of specimens shows strain-softening and a clear shear band in compression tests, but strain-hardening without any clear shear band in extension tests for the same absolute value of axial strain.     

海洋调查数据的可视化建模及实现方法

科学计算可视化作为新一代的分析工具 ,正在进入物理海洋学领域。文中介绍对海洋调查数据进行可视化的关键问题——数据建模 ,并从分析海洋调查数据的特点出发提出针对海洋研究中可视化建模的原则和有效途径 ,给出相关的实现方法。其中 ,重点讨论局部体样条建模中必须面对的区域分割优化问题 ,引入遗传算法并给出较好的解决方案。     

The petroleum evaluation of a tectonically complex area: The western margin of the Southeast Basin (France)

The Southeast Basin of France is the thickest onshore French sedimentary basin which contains locally as much as 10 km of Mesozoic-Cenozoic sediment. Basin development occurred in several stages between late Carboniferous and late Cretaceous times. Partial tectonic inversion took place during two compressive events, the so-called ‘Pyrenean’ and ‘Alpine’ phases of late Cretaceous-early Tertiary and late Tertiary ages respectively. They are separated by an intervening stretching event of Oligocene age, which further south resulted in the opening of the western Mediterranean oceanic basin. As a result of this complex tectonic history, structural traps were difficult to image on the seismic data shot during the first phase of exploration prior to 1980. Oil and gas natural seeps, and shows in several wells, indicate that some petroleum systems are, or have been active, at least in some places.The present erosional western margin of the basin is more or less superimposed on the initial Triassic-Jurassic margin. Margin subsidence and Tertiary inversion are discussed using regional sections on which the polyphase history of the entire basin is well shown. These sections are located on three major segments where the Mesozoic margin is either partly preserved (Ardèche), or has been partly inverted in late Tertiary times (Vercors-Chartreuse), or has been completely inverted in early Tertiary times (Corbières-eastern Pyrenees). 1-D ‘Genex’ basin modelling on the Ardèche segment, and 2-D ‘Thrustpack’ structural-maturity modelling in the Vercors-Chartreuse segment are used to further assess the remaining petroleum plays.     

Application of Microbial BOD Sensors in Marine Monitoring

A strain of yeast, which can endure high osmotic pressure, is employed for the sensitive material of the microbial BOD sensor. Two immobilization methods are used, I.e. Calcium alginate gel be ads and PV A gel beads. The results show that the PVA gel beads is better. The influences of osmosis and heavy metal ions on the yeast entrapped in the PVA gel beads are also studied in the experiment.     

Fast static correction methods for high-frequency multichannel marine seismic reflection data: A high-resolution seismic study of channel-levee systems on the Bengal Fan

Very high-frequency marine multichannel seismic reflection data generated by small-volume air- or waterguns allow detailed, high-resolution studies of sedimentary structures of the order of one to few metres wavelength. The high-frequency content, however, requires (1) a very exact knowledge of the source and receiver positions, and (2) the development of data processing methods which take this exact geometry into account. Static corrections are crucial for the quality of very high-frequency stacked data because static shifts caused by variations of the source and streamer depths are of the order of half to one dominant wavelength, so that they can lead to destructive interference during stacking of CDP sorted traces. As common surface-consistent residual static correction methods developed for land seismic data require fixed shot and receiver locations two simple and fast techniques have been developed for marine seismic data with moving sources and receivers to correct such static shifts. The first method – called CDP static correction method – is based on a simultaneous recording of Parasound sediment echosounder and multichannel seismic reflection data. It compares the depth information derived from the first arrivals of both data sets to calculate static correction time shifts for each seismic channel relative to the Parasound water depths. The second method – called average static correction method – utilises the fact that the streamer depth is mainly controlled by bird units, which keep the streamer in a predefined depth at certain increments but do not prevent the streamer from being slightly buoyant in-between. In case of calm weather conditions these streamer bendings mainly contribute to the overall static time shifts, whereas depth variations of the source are negligible. Hence, mean static correction time shifts are calculated for each channel by averaging the depth values determined at each geophone group position for several subsequent shots. Application of both methods to data of a high-resolution seismic survey of channel-levee systems on the Bengal Fan shows that the quality of the stacked section can be improved significantly compared to stacking results achieved without preceding static corrections. The optimised records show sedimentary features in great detail, that are not visible without static corrections. Limitations only result from the sea floor topography. The CDP static correction method generally provides more coherent reflections than the average static correction method but can only be applied in areas with rather flat sea floor, where no diffraction hyperbolae occur. In contrast, the average static correction method can also be used in regions with rough morphology, but the coherency of reflections is slightly reduced compared to the results of the CDP static correction method.