Interaction of cnoidal waves with an array of vertical concentric porous cylinders

An array of large concentric porous cylinder arrays is mounted in shallow water exposed to cnoidal waves. The interactions between waves and cylinders are studied theoretically using an eigenfunction expansion approach. Semi-analytical solutions of hydrodynamic loads and wave run-up on each cylinder are obtained using first approximation to cnoidal waves. The square array configuration of four-legged identical concentric porous cylinder is investigated in present study. Numerical results reveal the variation of dimensionless wave force and wave run-up on individual cylinder with angle of incidence, porosity parameter, spacing between outer and inner cylinders, spacing between concentric porous cylinders and wave parameter. Different mechanism of wave force is found under different range of scattering parameter.     

Experimental and theoretical study of a cylindrical oscillating water column device with a quadratic power take-off model

The wave power extraction by a cylindrical oscillating water column (OWC) device with a quadratic power take-off (PTO) model was studied experimentally and theoretically. In the experiment, a scaled model OWC was tested in a wave flume, with an orifice being used to simulate a quadratic PTO mechanism. In the theoretical analysis, the quadratic PTO model was linearized based on Lorenz's principle of equivalent work, which allows us to perform a frequency domain analysis using an eigen-function matching method. The effects of higher harmonic components and the spatial non-uniformity of the surface velocity inside the chamber were discussed. A semi-analytical model was proposed to understand the viscous loss affecting the measured capture length. Our treatment of the quadratic PTO model was validated by comparing quasi-linear theoretical capture length and the laboratory measurement. Our results also showed that the effects of spatial non-uniformity and viscous loss could be noticeable for shorter waves.     

CFD investigations of OXYFLUX device,an innovative wave pump technology for artificial downwelling of surface water

No other environmental variable of such ecological importance to estuarine and coastal marine ecosystems around the world has changed so drastically, in such a short period of time, as dissolved oxygen in coastal waters. The prevalent methods for counteracting anoxic sea events are indirect measures which aim to cut-down anthropic loads introduced in river and marine environments. To date, no direct approaches, like artificial devices have been investigated except the WEBAP and OXYFLUX devices. The present paper adopts a numerical approach to the analysis of the pumped surface water as well as the analysis of the dynamic response of the OXYFLUX device. By means of a CFD-RANS code and through the application of overset grid method, the 1/16 OXYFLUX model’s dynamic response and pumping performance are evaluated. The appropriate grid is selected after an extensive sensitivity analysis carried out on 9 different grids. The CFD model is validated by comparing numerical and physical results of heave decay test, heave response, and surface water discharge under the action of regular waves. The extensive comparison with experimental results shows consistently accurate predictions. The main findings of the study show that nonlinear effects remarkable reduce the dynamic behaviour of the OXYFLUX and generate an unexpected second harmonic for pitch response intensifying the overtopping discharge also for small waves caused by the summer's low intensity winds.     

基于OS071X测波雷达的波浪探测分析

文章利用舟山海洋环境监测站2014年第16号台风"凤凰"过境影响期间,对OS071X测波雷达和3m波浪浮标在同一海域内的波浪探测资料进行了对比验证。通过分析,OS071X测波雷达探测反演的有效波高、周期与3m波浪浮标探测结果对比,二者按先后顺序的均方根误差分别为0.27m和0.29m,相关系数分别为0.93和0.90。结果表明,OS071X测波雷达系统的探测精度得到了验证,能够满足实时探测近岸海域波浪的需求。     

Comparative analysis of significant wave height between a new Southern Ocean buoy and satellite altimeter

中国于2019年第35次南极考察中,首次在南大洋布放了锚系实时综合观测浮标(西风带海洋环境监测浮标,WEMB),为深入了解此海区的海洋环境变化提供了宝贵资料.国家海洋技术中心WEMB研究团队基于AVISO公开发布的多颗卫星高度计L3产品,通过数据配对,误差统计和最小二乘线性拟合等方法,对西风带海洋环境监测浮标的有效波高数据误差进行了分析与校正.校正后的浮标有效波高统计显示西风带常年处于大浪以上海况,观测期间内57％处于巨浪海况,并且伴随有高度相关的大风天气.     

Extracting energy while reducing hydroelastic responses of VLFS using a modular raft wec-type attachment

This paper presents the use of a modular raft Wave Energy Converter (WEC)-type attachment at the fore edge of a rectangular Very Large Floating Structure (VLFS) for extracting wave energy while reducing hydroelastic responses of the VLFS under wave action. The proposed modular attachment comprises multiple independent auxiliary pontoons (i.e. modules) that are connected to the fore edge of the VLFS with hinges and linear Power Take-Off (PTO) systems. For the hydroelastic analysis, the auxiliary pontoons and the VLFS are modelled by using the Mindlin plate theory while the linear wave theory is used for modelling the fluid motion. The analysis is performed in the frequency domain using the hybrid Finite Element-Boundary Element (FE-BE) method. Parametric studies are carried out to investigate the effects of pontoon length, PTO damping coefficient, gap between auxiliary pontoons, and incident wave angle on the power capture factor as well as reductions in the hydroelastic responses of the VLFS with the modular attachment. It is found that in oblique waves, the modular attachment comprising multiple narrow pontoons outperforms the corresponding rigid attachment that consists of a single wide pontoon with respect to the power capture factor and the reduction in the deflection of the VLFS. In addition, it is possible to have a considerable gap between pontoons without significantly compromising the effectiveness of the modular attachment.     

Experimental investigation on a cabin-suspended catamaran in terms of motion reduction and wave energy harvesting by means of a semi-active motion control system

A novel concept catamaran equipped with a suspended cabin, named Wave Harmonizer Type 4 (WHzer-4), is proposed and evaluated. The mass-spring-mass system is constructed by mounting four sets of suspensions in-between the cabin and the twin-hull. Two sets of dual motor/generators (M/Gs) are attached on the center beam of the cabin's deck fore and aft. Each shaft-end of the dual M/Gs is connected to the twin-hull through a rack-pinion gear unit. In this way the vertical relative motion between the cabin and the twin-hull can be transferred into the rotational motion of the M/Gs, and vice versa. A semi-active motion control system, which contains a proportional-integral (PI) controller, is designed and applied to each of the dual M/Gs for the aim of absorbing wave energy under the condition of suppressing the local vertical velocity of the cabin as much as possible. A 1/5 scale model ship with a length of 1.6 m is built, and a forced-oscillation bench test is implemented to validate the performance of the control system. Then, a series of towing tank tests is carried out in regular head waves. The heave and pitch responses of the cabin, those of the twin-hull and the corresponding wave energy capture width ratio (CWR) at five control scenarios and two reference scenarios are investigated. Discussion on the results of the tank test shows that the motion reduction of the cabin and the wave energy harvesting can be achieved simultaneously at a few wave conditions. However, at other conditions, although noticeable amount of wave energy is harvested, motion reduction of the heave and pitch of the cabin could not be obtained at the same time. It is suggested that varying the gain settings of the PI controllers according to the location of the controllers may improve the effectiveness of the proposed control system.     

Wave tank and bench-top control testing of a wave energy converter

An increasing number of experiments are being conducted to study the design and performance of wave energy converters. Often in these tests, a real-time realization of prospective control algorithms is applied in order to assess and optimize energy absorption as well as other factors. This paper details the design and execution of an experiment for evaluating the capability of a model-scale WEC to execute basic control algorithms. Model-scale hardware, system, and experimental design are considered, with a focus on providing an experimental setup capable of meeting the dynamic requirements of a control system. To more efficiently execute such tests, a dry bench testing method is proposed and utilized to allow for controller tuning and to give an initial assessment of controller performance; this is followed by wave tank testing. The trends from the dry bench test and wave tank test results show good agreement with theory and confirm the ability of a relatively simple feedback controller to substantially improve energy absorption. Additionally, the dry bench testing approach is shown to be an effective and efficient means of designing and testing both controllers and actuator systems for wave energy converters.     

Hydrodynamic performance of a T-shaped floating breakwater

The comprehensive utilization of floating breakwaters, specially acting as a supporting structure for offshore marine renewable energy explorations, has received more and more attention recently. Based on linear water-wave theory, the hydrodynamic performance of a T-shaped floating breakwater is semi-analytically investigated through the matched eigenfunction expansion method (MEEM). Auxiliary functions, to speed up the convergence and improve the accuracy in the numerical computations, are introduced to represent the singular behavior of fluid field near the lower salient corners of the structure. The effects of the height and installation position of the vertical screen on the reflection and transmission coefficients, dynamic response and wave forces are examined. It is found that the presence of the screen shifts the resonance frequency of RAO for both surge and pitch modes to the low-frequency area, while has no effect on heave mode. The identical added masses, damping and transmission coefficients can be obtained in the cases where the screen holds the same distance away from the longitudinal central axis of the upper box-type structure. Moreover, a relatively small pitch response can be achieved in a wide wave–frequency range, when the breakwater is Γ-shaped.     

An efficient hybrid integral-equation method for point-absorber wave energy converters with a vertical axis of symmetry

To assist in the prototyping and controller design of point-absorber wave energy converters (WECs), an easy-to-implement hybrid integral-equation method is presented for computing the frequency-domain hydrodynamic properties of bodies with a vertical axis of symmetry in waves. The current hybrid method decomposes the flow domain into two parts: an inner domain containing the body and an outer domain extending to infinity. The solution in the inner domain is computed using the boundary-element method, and the outer-domain solution is expressed using eigenfunctions. Proper matching at the domain boundary is achieved by enforcing continuity of velocity potential and its normal derivative. Body symmetry allows efficient computation using ring sources in the inner domain. The current method is successfully applied to three different body geometries including a vertical truncated floating cylinder, the McIver toroid, and the coaxial-cylinder WEC being developed in the authors’ laboratory. In particular, the current results indicate that, by replacing the flat bottom of the coaxial-cylinder WEC with the Berkeley-Wedge (BW) shape, viscous effect can be significantly reduced with only minor negative impact on wave-exciting force, thus increasing WEC efficiency. Finally, by comparing to experimental measurements, the current method is demonstrated to accurately predict the heave added mass and wave-exciting force on the coaxial-cylinder WEC with BW geometry. If a viscous damping correction factor is used, the heave motion amplitude can also be accurately computed.