多级串联非比例阻尼隔震结构地震响应分析

建立了多级串联非比例阻尼隔震结构动力分析模型;引用分区瑞利阻尼模型将非比例阻尼矩阵分解为瑞利阻尼矩阵和体现非比例阻尼的余项阻尼矩阵,推导出结构的阻尼矩阵;并编制了MATLAB动力时程分析程序,对一实际隔震工程进行地震响应分析.结果表明:随着下部结构刚度的增加,结构的层剪力比和隔震层位移响应峰值均趋向于基础隔震结构的对应值;当下部结构为一层,且层间刚度大于上部结构底层层间刚度4～6倍时,可以近似按基础隔震结构进行动力分析.     

原地宇宙成因核素测年中石英样品分离提纯的几组实验对比

原地宇宙成因核素测年方法在地质及地理研究领域应用广泛,测年对象众多。石英因其致密的晶体结构不易被大气成因10Be污染,以及较低的27Al含量的特点而成为宇宙成因核素测年方法中一种理想的测年物质。在分离石英样品10Be和26Al的实验流程中,石英的提纯是其中的一个关键环节。原始的HCl/H2O2和HF/HNO3蚀刻分离提纯石英方法应用广泛、安全可靠,但处理样品周期长、效率较低。因此,在原始流程的基础上,设计了3组实验流程与原始流程进行对比。结果显示,在样品石英纯度较高的基础上,可以通过减少超声波使用时间、增加蚀刻溶液浓度及每步样品处理量的方法,提高样品的处理效率,同时可以用加热磁力搅拌器替代超声波清洗器进行石英样品的HF/HNO3蚀刻提纯     

15×104 m3立式储罐隔震设计分析

为了研究15×104m3立式储罐隔震设计影响因素,采用有限元数值仿真技术,分析了隔震刚度、浮顶质量、储液密度、罐壁厚度、罐壁的材料弹性模量、储液高度与罐半径比值对储罐的晃动频率和液固耦合频率的影响并与时程分析对照。结果表明:储罐液固耦合振动频率对隔震刚度敏感,隔震刚度较低时,液固耦合刚度的下降,使基底剪力变小;隔震刚度对储罐的液体晃动频率的影响不大,在一定的隔震周期范围内,波高无放大效应;隔震设计时,浮顶的影响可忽略;储液高度与储罐半径比对储罐的液固耦合频率和晃动频率影响较大,隔震设计时存在优化段;储液密度、罐壁厚度、材料弹性模量,隔震设计时可不考虑其影响,进行地震动台实验时,可考虑用其他材料代替钢材,不影响分析结果。     

南海海域4种笛鲷的微卫星DNA分析

采用聚丙烯酰胺凝胶电泳技术,从20对西大西洋笛鲷(Lutjanus campechanus)的微卫星引物中筛选适用于红鳍笛鲷(L.erythopterus)、勒氏笛鲷(L.russellii)、紫红笛鲷(L.argentimaculatus)和约氏笛鲷(L.johnii)基因组分析的微卫星引物,分析4种笛鲷的遗传多样性及系统发生。经反应条件的优化,从20对引物中筛选出17对可稳定扩增出特异片段的引物。通过测序证实扩增产物含微卫星位点后,以该17对引物对4个种的群体进行遗传多样性分析。其中16对可在约氏笛鲷、勒氏笛鲷、紫红笛鲷基因组中扩增出重复性好的特异性条带,分别有65%、65%、60%呈现出种内多态;15对可在红鳍笛鲷中扩增出重复性好的特异性条带,并且全部呈现出种内多态。四种笛鲷中,红鳍笛鲷的多态性最高,高度多态基因座占检测座位的66.67%;勒氏笛鲷的多态性最低,低度多态基因座占43.75%。获得3个种间特异性分子标记。用DS和DA两种方法计算4种笛鲷的遗传距离,构建了系统发生树。     

复合隔震支座在网格屋盖结构中的应用研究

将铅芯橡胶隔震垫与碟簧组合形成复合隔震垫,并应用于网格屋盖结构,利用串联弹簧模型预估铅芯橡胶隔震垫参数,利用单质点弹簧模型预估碟簧参数,结合实际工程,进行了模态分析、水平地震动时程分析及竖向地震动时程分析,表明复合隔震技术降低屋盖、下部结构加速度反应60%左右,降低由于地震引起的基顶反力约30%,但水平地震下隔震屋盖的侧移增大显著,应引起注意;文中提出的隔震垫参数预估模型得到了地震动时程分析的验证,可为工程参考。     

Development of a tunable friction pendulum system for semi‐active control of building structures under earthquake ground motions

The Friction Pendulum System (FPS) isolator is commonly used as a base isolation system in buildings. In this paper, a new tunable FPS (TFPS) isolator is proposed and developed to act as a semi‐active control system by combining the traditional FPS and semi‐active control concept. Theoretical analysis and physical tests were carried out to investigate the behavior of the proposed TFPS isolator. The experimental and theoretical results were in good agreement, both suggesting that the friction force of the TFPS isolator can be tuned to achieve seismic isolation of the structure. A series of numerical simulations of a base‐isolated structure equipped with the proposed TFPS isolator and subjected to earthquake ground motions were also conducted. In the analyses, the linear quadratic regulator (LQR) method was adopted to control the friction force of the proposed TFPS, and the applicability and effectiveness of the TFPS in controlling the structure's seismic responses were investigated. The simulation results showed that the TFPS can reduce the displacement of the isolation layer without significantly increasing the floor acceleration and inter‐story displacement of the superstructure, confirming that the TFPS can effectively control a base‐isolated structure under earthquake ground motions.     

基于小波变换的层间隔震结构地震响应分析

利用小波多分辨率分析将地震动加速度分解为多频段小波分量,并运用复模态方法推导其计算层间隔震体系在地震作用下的动力响应公式,讨论各频段地震信号及结构响应的能量分配。同时利用小波时频工具分析地震动能量在时频域内的分布对层间隔震结构响应的影响,进而为考察地震动非平稳性对层间隔震结构非线性分析的影响提供方法。利用小波分析的以上优势,对一典型层间隔震结构分别进行弹性和弹塑性分析,结果表明弹性体系在地震作用下的响应可由该地震波各小波分量的响应叠加而得,地震动能量在时间上的集中会对层间隔震结构响应产生不利影响。     

Real‐time hybrid testing of a smart base isolation system

Real‐time hybrid testing is a very effective technique for evaluating the dynamic responses of rate‐dependent structural systems subjected to earthquake excitation. A smart base isolation system has been proposed by others using conventional low‐damping isolators and controllable damping devices such as magnetorheological (MR) dampers to achieve specified control target performance. In this paper, real‐time hybrid tests of a smart base isolation system are conducted. The simulation is for a base‐isolated two‐degrees‐of‐freedom building model where the superstructure and the low‐damping base isolator are numerically simulated, and the MR damper is physically tested. The target displacement obtained from the step‐by‐step integration of the numerical substructure is imposed on the MR damper, which is driven by three different control algorithms in real‐time. To compensate the actuator delay and improve the accuracy of the test, an adaptive phase‐lead compensator is implemented. The accuracy of each test is investigated by using the root mean square error and the tracking indicator. Experimental results demonstrate that the hybrid testing procedure using the proposed actuator compensation techniques is effective for investigating the control performance of the MR damper in a smart base isolation system. Copyright © 2013 John Wiley & Sons, Ltd.     

同高宽比弹塑性隔振建筑结构的抗震性能试验研究

研究以某同高宽比弹塑性隔振建筑结构为工程实例,采用SAP2000软件构建了同高宽比弹塑性隔振建筑结构的有限元模型,并进行了模型材料和相应参数选取;在此基础上,利用循环侧推分析隔振建筑结构中各构件的内力及变形情况,建立隔震建筑结构损失模型,同时为了提高其抗震性评估精准度,采用动力弹塑性顶层位移情况反应隔震建筑结构的抗震性能。工程实例分析结果表明,普通建筑结构主要控制层间位移响应,无论是在8度频发地震作用下还是在8度特大地震作用下,隔震建筑结构的顶部加速度响应均远远小于普通建筑结构,且仍然处于完全弹性工作状态,结构构件并未发生破坏,保证了建筑内部人们的生命财产安全,同时便于震后快速修复,相比于普通建筑结构,同高宽比弹塑性隔振建筑结构的抗震性能更优。     

Seismic reliability‐based ductility demand evaluation for inelastic base‐isolated structures with friction pendulum devices

The aim of this work is to propose seismic reliability‐based relationships between the strength reduction factors and the displacement ductility demand of nonlinear structural systems equipped with friction pendulum isolators (FPS) depending on the structural properties. The isolated structures are described by employing an equivalent 2dof model characterized by a perfectly elastoplastic rule to account for the inelastic response of the superstructure, whereas, the FPS behavior is described by a velocity‐dependent model. An extensive parametric study is carried out encompassing a wide range of elastic and inelastic building properties, different seismic intensity levels and considering the friction coefficient as a random variable. Defined a set of natural seismic records and scaled to the seismic intensity corresponding to life safety limit state for L'Aquila site (Italy) according to NTC08, the inelastic characteristics of the superstructures are designed as the ratio between the average elastic responses and increasing strength reduction factors. Incremental dynamic analyses (IDAs) are developed to evaluate the seismic fragility curves of both the inelastic superstructure and the isolation level assuming different values of the corresponding limit states. Integrating the fragility curves with the seismic hazard curves related to L'Aquila site (Italy), the reliability curves of the equivalent inelastic base‐isolated structural systems, with a design life of 50 years, are derived proposing seismic reliability‐based regression expressions between the displacement ductility demand and the strength reduction factors for the superstructure as well as seismic reliability‐based design (SRBD) abacuses useful to define the FPS properties. Copyright © 2016 John Wiley & Sons, Ltd.