深层搅拌法在超软弱港口地基上的工程应用

某港口堆场地基上部5．0m系吹填而成，地表下18m范围均属软土，经真空预压初级加固后地基承载力仅在80—90kPa，局部区域上部淤泥土层土性指标较差，含水量大于50％，地基承载力不足60kPa。为了使地基达到230kPa的承载要求，设计采用深层搅拌法加固超软弱地基。通过现场成桩工艺试验和检测表明，桩身水泥土强度在90d龄期时大于1．80MPa，单桩承载力标准值大于150kN，以φ600桩径、桩长13．5m、置换率为0．308和φ500桩径、桩长13．5m、置换率为0．267两种方案布置的复合地基承载力标准值均超过了230kPa的设计要求。试验结果表明，深层搅拌法在港口超软弱地基土应用只要施工工艺适当，完全可以使地基承载力提高2—3．5倍以土，从而节省大量的工程投资。     

低凝固温度琼脂糖的制备方法研究

以石花菜分级得到的琼脂糖为原料，采用甲基化方法制备低凝固温度琼脂糖。所得到的低凝固温度琼脂糖产品的凝固温度为30．1℃(1.5％浓度)，融化温度为64．8℃(1．5％浓度)，凝胶强度为264g／cm^2(1.0％浓度)，主要质量标准与Sigma公司的低凝固温度琼脂糖产品接近，符合低凝固温度琼脂糖产品的质量要求。     

含盐量对松嫩平原碳酸盐渍土抗剪强度的影响

松嫩平原分布着大量的碳酸盐渍土,其不良的工程性质给穿越其中的道路质量造成不同程度的影响。由于盐渍土所含易溶盐成分主要为碳酸氢钠,该研究通过向碳酸盐渍土内加入碳酸氢钠制备不同含盐量的盐渍土,进行室内直剪试验。试验表明：随着含盐量的增加土的粘聚力减小,内摩擦角有先减小后变大的趋势;随着含水量的增加,土的含盐量越高,土的粘聚力减小越明显。易溶盐在土中的状态形式是影响其抗剪强度参数变化的一个重要原因。     

蚀变岩的蠕变特性研究

以某水电站工程项目为依托,利用自行研制的试验仪器对大量的蚀变岩做了单轴压缩流变试验。通过对试验数据的处理和分析,得到了该种岩石的流变,并对蚀变岩的蠕变特性进行了分析总结,为工程设计提供了试验依据。     

节理岩体卸荷强度特性的试验研究

卸荷状态工程岩体的强度特性与传统的加载岩体有本质的区别。目前对于岩石卸荷强度特性的研究比较多见,但对于含节理的岩体在卸荷应力状态下的强度特性,尤其是节理面对其强度的影响研究实属少见。本文通过岩体三轴模拟试验研究了卸荷应力状态下节理岩体的破坏特征,突出考虑了节理面性质对卸荷强度的影响,在此基础上提出了节理岩体卸荷强度准则的一般表达式并进行了对比验证。     

200～300N高强度合成金刚石及其在钻探中的应用

对会“打滑”地层,国内外均为难题,新研究的技术是：（１）用特殊的新构思,运用内设备,压制出可批量２供应的高强度金刚石,这种高强度金刚石可承受比目前高得多的钻压;（２）运用强力钻进的配套技术,用上述高强度金刚石制作头。     

饱和软土压缩曲线的“反常”现象

饱和软土压缩试验时,经常出现压缩曲线“反常”、压缩系数“倒大”的现象。它是土的原始结构发生破坏前后的不同压缩性的客观反映。饱和软土的结构力很微弱,唯质量好的原状土才能见到这种“反常”。应从成孔、取样、测试及资料整理等多个环节保证其工程意义。     

Strength and stability of frictional sliding of gabbro gouge at elevated temperatures

To investigate the strength of frictional sliding and stability of mafic lower crust, we conducted experiments on oven-dried gabbro gouge of 1 mm thick sandwiched between country rock pieces (with gouge inclined 35° to the sample axis) at slip rates of 1.22 × 10^− 3 mm/s and 1.22 × 10^− 4 mm/s and elevated temperatures up to 615 °C. Special attention has been paid to whether transition from velocity weakening to velocity strengthening occurs due to the elevation of temperature.Two series of experiments were conducted with normal stresses of 200 MPa and 300 MPa, respectively. For both normal stresses, the friction strengths are comparable at least up to 510 °C, with no significant weakening effect of increasing temperature. Comparison of our results with Byerlee's rule on a strike slip fault with a specific temperature profile in the Zhangbei region of North China shows that the strength given by experiments are around that given by Byerlee's rule and a little greater in the high temperature range.At 200 MPa normal stress, the steady-state rate dependence a − b shows only positive values, probably still in the “run-in” process where velocity strengthening is a common feature. With a normal stress of 300 MPa, the values of steady-state rate dependence decreases systematically with increasing temperature, and stick-slip occurred at 615 °C. Considering the limited displacement, limited normal stress applied and the effect of normal stress for the temperatures above 420 °C, it is inferred here that velocity weakening may be the typical behaviour at higher normal stress for temperature above 420 °C and at least up to 615 °C, which covers most of the temperature range in the lower crust of geologically stable continental interior. For a dry mafic lower crust in cool continental interiors where frictional sliding prevails over plastic flow, unstable slip nucleation may occur to generate earthquakes.     

Uniaxial compression and tension tests of anthracite and loading rate dependence of peak strength

The mechanical characteristics of coal under uniaxial compressive stress and uniaxial tensile stress are key factors in investigations of the stability of galleries and coal faces, and are vital considerations for the efficient design of coalmines, disaster prevention, and environmental preservation. These mechanical characteristics have long been a topic of research, but remain insufficiently understood. In this study we performed uniaxial compression tests and uniaxial tension tests on coal, with particular attention to two concerns. The first was to measure the loading rate dependence of the peak strength of coal. Coal shows high sample-to-sample scatter in strength; test methods that are successful in comparatively homogeneous rock types cannot be used for coal. We therefore used an alternative test method that was recently developed by the authors. Anthracite samples were subjected to alternating slow and fast strain rates. Measured variations in stress during this process were used to estimate the loading rate dependence of peak strength. The second objective was to obtain complete stress–strain curves for coal under uniaxial tensile stress. It is difficult to hold samples secure during a tensile test; consequently, such curves have yet to be obtained. This study presents a successful application of the authors' method to the analysis of coal samples, yielding a complete stress–strain curve under tensile stress. The two methods presented here hold promise for application not only to anthracite but also to a wide variety of coals. It is possible to derive the values of the constants used in constitutive equations from the obtained experimental results. Once these equations are determined, they can be incorporated into finite-element software to investigate various time-dependent behaviors of coal and aid in the efficient design of coalmines and the prevention of subsidence and mine disasters.