Fundamental study on the response characteristics of drivers during an earthquake based on driving simulator experiments

After the 1995 Kobe earthquake, the expressway structures in Japan were retrofitted and they will not now be seriously damaged under a certain level of strong earthquake motion. However, the stability of a moving vehicle has not been investigated yet. It has been reported that drivers feel seismically induced vibrations, especially in the transverse direction of vehicles. Owing to this phenomenon, drivers have some difficulty in controlling the vehicles during strong shaking. For further safety promotion of the expressway networks, it is important to understand the drivers' reactions to seismic motion. The present authors have performed a series of seismic response analyses of a moving vehicle to investigate its response characteristics based on numerical simulation. However, the responses of the driver were not considered in the simulation process. In order to investigate the drivers' reactions during an earthquake, a series of virtual tests were conducted using a driving simulator. This driving simulator has six servomotor‐powered electric actuators that control its motions. Several types of tests were carried out for different examinees to investigate drivers' responses while controlling the simulator under seismic motion. The results of this study showed that a larger response time lag to strong shaking and over turning of the steering wheel may shift the vehicle into the next lane. According to this finding, trafficaccidents could possibly occur under strong ground shaking in the case of heavy traffic. Copyright © 2004 John Wiley & Sons, Ltd.     

A modal pushover analysis procedure to estimate seismic demands for unsymmetric‐plan buildings

An Erratum has been published for this article in Earthquake Engng. Struct. Dyn. 2004; 33:1429. Based on structural dynamics theory, the modal pushover analysis (MPA) procedure retains the conceptual simplicity of current procedures with invariant force distribution, now common in structural engineering practice. The MPA procedure for estimating seismic demands is extended to unsymmetric‐plan buildings. In the MPA procedure, the seismic demand due to individual terms in the modal expansion of the effective earthquake forces is determined by non‐linear static analysis using the inertia force distribution for each mode, which for unsymmetric buildings includes two lateral forces and torque at each floor level. These ‘modal’ demands due to the first few terms of the modal expansion are then combined by the CQC rule to obtain an estimate of the total seismic demand for inelastic systems. When applied to elastic systems, the MPA procedure is equivalent to standard response spectrum analysis (RSA). The MPA estimates of seismic demand for torsionally‐stiff and torsionally‐flexible unsymmetric systems are shown to be similarly accurate as they are for the symmetric building; however, the results deteriorate for a torsionally‐similarly‐stiff unsymmetric‐plan system and the ground motion considered because (a) elastic modes are strongly coupled, and (b) roof displacement is underestimated by the CQC modal combination rule (which would also limit accuracy of RSA for linearly elastic systems). Copyright © 2004 John Wiley & Sons, Ltd.     

Seismic performance evaluation of steel arch bridges against major earthquakes. Part 1: dynamic analysis approach

In this study the inelastic behavior of steel arch bridges subjected to strong ground motions from major earthquakes is investigated by dynamic analyses of a typical steel arch bridge using a three‐dimensional (3D) analytical model, since checking seismic performance against severe earthquakes is not usually performed when designing such kinds of bridge. The bridge considered is an upper‐deck steel arch bridge having a reinforced concrete (RC) deck, steel I‐section girders and steel arch ribs. The input ground motions are accelerograms which are modified ground motions based on the records from the 1995 Hyogoken‐Nanbu earthquake. Both the longitudinal and transverse dynamic characteristics of the bridge are studied by investigation of time‐history responses of the main parameters. It is found that seismic responses are small when subjected to the longitudinal excitation, but significantly large under the transverse ground motion due to plasticization formed in some segments such as arch rib ends and side pier bases where axial force levels are very high. Finally, a seismic performance evaluation method based on the response strain index is proposed for such steel bridge structures. Copyright © 2004 John Wiley & Sons, Ltd.     

Seismic tests on reinforced concrete and steel frames retrofitted with dissipative braces

Seismic tests have been conducted on two 3‐storey structures protected with pressurized fluid‐viscous spring damper devices. One of the structures was a reinforced concrete frame with clay elements in the slabs, while the other one was a steel frame with steel/concrete composite slabs. The spring dampers were installed through K bracing in between the floors. The tests were performed by means of the pseudodynamic method, which allowed the use of large and full‐size specimens, and by implementing a specific compensation strategy for the strain‐rate effect at the devices. The test results allowed the verification of the adequacy of the attachment system as well as the comparison of the behaviour of the unprotected buildings with several protected configurations, showing the benefits of the application of the devices and the characteristics of their performance. The response of the protected structures was always safer than that of the unprotected ones mainly due to a significant increase of equivalent damping. The increase in the damping ratio depends on the level of deformation. Copyright © 2004 John Wiley & Sons, Ltd.     

A comparative study on the illite crystallinity and the clay mineral reflectance spectral index for subdividing the very low-grade metamorphic belt along the Lizhou-Hekou geological section in the Youjiang sedimentary basin, Guangxi, China

To examine the application potential of hyperspectral remote sensing techniques in classifying very low-grade metamorphic belts, the composition of clay minerals and the cyrstallinity of illite from mudstones were measured using XRD and VIS-SWIR (400-2500 nm) reflectance spectroscopy. Based on the illite cyrstallinity, Kubler Index (KI), the Early Triassic LuoLou Group and the Middle Triassic lower Baifeng Formation were classified as the lower Epizone with KI△2θ° ranging from 0.22 to 0.25, the upper Baifeng Formation as upper anchizone with KI△2θ°ranging from 0.26 to 0.33, and the Hekou Formation as lower anchizone with KI△2θ° ranging from 0.38 to 0.40. According to a KI△2θ° value of 0.43, it is possible that there may exist a local diagenetic zone in the upper strata. The illite cyrstallinity Kubler index and the metamorphic grade increase from the bottom to the top of the stratigraphic sequence. The metamorphic grade boundaries nearly match the stratigraphic boundaries, indicating a burial metamorphism nature for the stratigraphic sequence. From the bottom to the top of the sequence, the spectral absorption band center of clay minerals from fresh rocks is around 2200 nm. The absorption band centers change towards shorter wavelengths: the Luolou Group being at 2220 nm, the Baifeng Formation at 2217-2213 nm, the lower member of the Hekou Formation at 2214-2206 nm, and the upper member of the Hekou Formation at 2205-2197 nm. The spectral absorption band center of illite shows the same change pattern. These results indicate that very low-grade metamorphic belts can be subdivided using spectral indices of clay minerals, which are measured by using field portable spectroradiometers. However, it may not work well with satellite and airborne sensors.     

新疆西南天山木扎尔特一带低压麻粒岩相变质作用P-T轨迹及其地质意义

本文首次报道在新疆西南天山木扎尔特一带发现了二辉石麻粒岩和麻粒岩相变质的堇青石榴矽线石片麻岩。二辉石麻粒岩的矿物组合为单斜辉石-斜方辉石-黑云母-角闪石-斜长石-石英。堇青石榴矽线石片麻岩矿物组合为堇青石-矽线石-石榴石-黑云母-斜长石-石英。岩石学和矿物学特征表明它们是典型的低压麻粒岩相变质岩石，其变质作用经历了两期演化：a．峰期麻粒岩相变质，T=681～705℃，P=5．4～5．8kbar；b．峰后角闪岩相退变阶段，T：571～637℃．P=4．7～5．3kbar。其变质作用P-T轨迹具有逆时针近等压降温(IBC)的特点，代表该地区可能为塔里木板块向伊犁．中天山板块俯冲过程中，在陆壳一侧所产生的陆源岩浆弧区域，由于受到下部岩浆热源的影响，在拉伸环境下出现低压麻粒岩相变质。通过分析低压麻粒岩相岩石与其南部高压一超高压变质带的大地构造位置和年代关系，我们认为该地区的低压麻粒岩相变质岩石可能与其南部的西天山高压一超高压变质带组成了双变质带。     

大别山太湖地区榴辉岩峰期变质条件与构造意义

大别山太湖地区曾被作为“冷”、“热”榴辉岩带的交界处所在，我们对大别山太湖地区的进行了1：10000地质填图，并详细研究了该地区榴辉岩的岩相学和矿物成分变化，以及KD值、峰期变质P-T条件。研究表明榴辉岩自南向北可分为三类：①朱家冲型榴辉岩；②大坝型榴辉岩；③金河桥型榴辉岩。其中朱家冲型榴辉岩和金河桥型榴辉岩显示出明显的温度、压力差异，它们形成的P-T条件分别为：P=2．14GPa、T=563℃和P=3．76GPa、T=791℃。大坝型榴辉岩的峰期变质P-T条件差别较大，在柯石英-石英相变线附近徘徊，变质环境相当于高压一超高压过渡环境。朱家冲型榴辉岩与大坝型榴辉岩分别对应于前人所划分的“冷”、“热”榴辉岩，并且两者在峰期，变质温、压条件上是连续变化的，没有明显的温、压间断。因此，我们认为本区所谓的“冷”、“热”榴辉岩带界线是不存在的。     

红透山矿床变质岩系褶皱构造特征浅析

红透山式铜-锌矿床形成于太古代克拉通裂谷槽盆中海底火山喷发-沉积环境。因此，矿床的空间展布严格受特定的含矿岩系所控制。槽盆构造中的岩层褶皱构造最发育，矿床赋存在具多期褶皱构造叠加的大型同倾向形褶皱内，褶皱的层间虚脱是控矿有利构造空间，可以借此预测矿体侧伏方向及赋存部位。     

Hydrothermal Mineralization on the Mesoproterozoic Passive Continental Margins of China： A Case Study of the Langshan-Zha＇ertaishan Belt, Inner Mongolia, China

Most ore-forming characteristics of the Langshan-Zha‘ertaishan hydrothermal exhalation belt, which consists of the Dongshengmiao, Huogeqi, Tanyaokou and Jiashengpan large-superlarge Zn-Pb-Cu-Fe sulfide deposits, are most similar to those of Mesoproterozoic SEDEX-type provinces of the world. The characteristics include: (1) All deposits of this type in the belt occur in third-order fault-basins in the Langshan-Zha‘ertaishan aulacogen along the northern margin of the North China Platform; (2) these deposits with all their orebodies hosted in the Mesoproterozoic impure dolomite-marble and carbonaceous phyllite (or schists) have an apparent stratabound nature; ores display laminated and banded structures, showing clear depositional features; (3) there is some evidence of syn-sedimentary faulting, which to a certain extent accounts for the temporal and spatial distribution and the size of the orebodies in all deposits and the formation of intrabed conglomerates and breccias; (4) they show lateral and vertical zonation of sulfides; (5) The Cu/(Pb Zn Cu) ratio of the large and thick Pb Zn Cu orebodies gradually decreases from bottom to top; and (6) barite is interbedded with pyrites and sometimes with sphalerite. However, some characteristics such as the Co/Ni radio of the pyrites, the volcanism, for example, of the Langshan-Zha‘ertalshan metallogenic belt, are different from those of the typical SEDEX deposits of the world. The meta-basic volcanic rock in Huogeqi, the sodic bimodal volcanic rocks in the Dongshengmiao and potassic bimodal-volcanic rocks with blastoporphyfitic and blasto-glomeroporphyritic texture as well as blasto-amygdaloidal structure in the Tanyaokou deposits have been discovered in the only ore-bearing second formation of the Langshan Group in the past 10 years. The metallogeny of some deposits hosted in the Langshan Group is closely related to syn-sedimentary volcanism based on the following facts: most of the lead isotopes in sphalerite, galena, pyrite, pyrrhotite and chalcopyrite plot on both sides of the line for the mantle or between the lines for the mantle and lower crust in the lead isotope composition diagram; cobalt content of some pyrites samples is much higher than the nickel content (Co/Ni= 11.91-12.19). Some volcanic blocks and debris have been picked out from some pyritic and pyrrhotitic ores. All Zn-Pb-Cu-Fe sulfide orebodies in these deposits occur in the strata overlying metamorphic volcanic rocks in the only ore-bearing second formation. In the Jiashengpan deposit that lacks syn-sedimentary volcanic rocks in the host succession only Pb and Zn ores occur without Cu ore, but in the Dongshengmiao, Tanyaokou and Huogeqi deposits with syn-sedimentary volcanic rocks in the host succession Cu ores occur. This indicates a relatively higher ore-forming temperature. The process of synsedimentary volcanic eruption directly supplied some ore-forming elements, and resulted in secular geothermal anomaly favorable for the circulation of a submarine convective hydrothermal system, which accounts for the precipitation of deep mineralizing fluids exhaling into anoxidic basins along the syn-sedimentary fault system in the Langshan-Zha‘ertai rift. The Dongshengmiao, Tanyaokou, and Huogeqi deposits hosted in the Langshan Group appear to be a transitional type of mineral deposit between SEDEX and VMS-types but with a bias towards SEDEX, while the Jiashengpan deposit hosted in the Zha‘ertai Group is of a characteristic SEDEX type. This evidence, together with other new discoveries of Mesoproterozoic volcanic rocks and the features of lithogeny and metallogeny of the Bayun Obo deposit in the neighborhood emphasize the diversity, complexity and uniqueness of the Mesoproterozoic Langshan-Zha‘ertal-Bayun Obo ore belt.     

A Sequence of Pan-African and Hercynian Events Recorded in Zircons from an Orthogneiss from the Hercynian Belt of Western Central Iberia--an Ion Microprobe U-Pb Study

Sensitive high-resolution ion microprobe U–Pb dating showsthat a biotite orthogneiss from the Hercynian belt of westerncentral Iberia contains 1000–300 Ma zircon. Older, 1000–570Ma ages within this range represent inherited, detrital materialamong which four age components may be recognized: