鄂尔多斯盆地中生代晚期以来大地热流的变化及其对生态环境格局和演变的影响

鄂尔多斯盆地的西北部、东北部和南部三个区域现今大地热流平均值分别为56．3、67．3和65．3mW／m^2，对应的生态环境格局也有明显的差异。研究表明，大地热流每增加4～5mW／m^2可使年均地表温度升高约l℃，使最低月均地表温度升高2。C以上。鄂尔多斯盆地东北部的平均大地热流比西北部高出11mW／m^2，东北部年均地表温度可能比西北部高出2～3℃，其最低月均地表温度可能比西北部高出4～6℃。西北部的大地热流平均值已经低于维持地表生态系统延续所需大地热流的临界值(57mW／m^2)，其自然生态系统整体上已经处于脆弱境地；东北部和南部的大地热流均大于57mW／m^2，自然生态系统均尚较稳健。东北部的沙漠化可能是风沙侵入的结果，其生态应该是可以恢复的。整个西北部作为一个整体看，72万年以前大地热流就已衰减到临界值以下，区域生态系统渐趋脆弱，开始整体上向荒漠化演变。     

大渡河次级支流斯合沟泥石流特征研究

泥石流作为地质环境较差、的山区的主要自然灾害之一，对它的研究尤其是泥石流规律方面的研究已取得了较大的成绩。但是对于泥石流的研究思路却有待进一步发展和完善，这在很大程度上将对山区的工程建设有很重要的指导意义。论文从工程地质研究思路的角度出发，对位于大渡河支流官料河上某水电站下闸址区的斯合沟泥石流进行了研究。文中采用工程地质分析的方法对大渡河次级支流斯台沟泥石流的形成环境(地层岩性条件、构造条件、地貌条件、气象条件、植被发育及人类活动)、基本特征(泥石流沟的基本特征、泥石流的堆积特征)进行了系统的研究，提出了该泥石流的形成演化过程及其机制模型(初期是堰塞式沟谷型泥石流，后期逐渐转向汇聚式沟谷型泥石流)。并在此基础上对泥石流沟沿岸的岸坡稳定性(可能泥石流的物源)等进行了评价分析。将定性分析和定量分析相结合，对泥石流的活动趋势以及可能泥石流的体积(未来泥石流形成将主要是在面蚀和沟蚀作用下的坡面泥石流。泥石流规模较小，且由于沟谷中下游坡降的进一步减缓，形成的泥石流物质一般将沿途停积．实际进入官料河内的体积很小)做出了较为科学的评价预测。经过这样的系统分析对工程建设中的泥石流防治有着积极的指导意义。     

碎屑流沿坡面运动的初步分析

本文分析了碎屑流沿坡面下滑过程中的运动特性,重点考察了床面摩擦系数、土体内摩擦角和坡角对碎屑流堆积形态的影响.     

Numerical simulations for coupled rock deformation and gas leak flow in parallel coal seams

Based on the new viewpoint of interaction mechanics for solid and gas, gas leakage in parallel deformable coal seams can be understood. That is, under the action of varied geophysical fields, the methane gas flow in a double deformable coal seam can be essentially considered to be compressible with time-dependent and mixed permeation and diffusion through a pore-cleat deformable, heterogeneous and anisotropic medium. From this new viewpoint, coupled mathematical models for coal seam deformation and gas leak flow in parallel coal seams were formulated and the numerical simulations for slow gas emission from the parallel coal seams are presented. It is found that coupled models might be close to reality. Meanwhile, a coupled model for solid deformation and gas leak flow can be applied to the problems of gas leak flow including mining engineering, gas drainage engineering and mining safety engineering in particular the prediction of the safe range using protective layer mining where coal and gas outbursts can efficiently be prevented. This revised version was published online in July 2006 with corrections to the Cover Date.     

Hydro-thermal performance of multilayer capillary barriers in arid lands

In this study, a capillary barrier system was designed and tested for an arid land environment. To simulate arid land conditions of high temperature and sub-irrigation systems, the barrier was subjected to thermal and hydraulic gradients in opposite directions; to test the barrier system under these severe conditions, an experimental apparatus was designed and fabricated. The multilayer capillary barrier consisted of three layers made of silica sand, a mixture of sand and bentonite in equal portions, and a mixture of clay (25%) and aggregate (75%). Several one dimensional coupled heat and moisture tests were performed. Temperature variations along the thickness of the barrier were recorded as a function of time, and at the end of each test, the barrier was sliced into small sections, for the determination of volumetric water content as a function of distance from the heat source. The experimental results were discussed in view of the barrier's intended purpose of its ability to store moisture for long time durations. Coupled heat and moisture flow equations were developed and solved numerically via a finite difference method. Diffusivity parameters were calculated by using experimental results, a numerical model, and Powell's conjugate directions method of nonlinear optimization. The model was calibrated and the results were discussed. Good agreement between calculated and experimental results was obtained. This revised version was published online in July 2006 with corrections to the Cover Date.     

Beds comprising debrite sandwiched within co-genetic turbidite: origin and widespread occurrence in distal depositional environments

Co‐genetic debrite–turbidite beds occur in a variety of modern and ancient turbidite systems. Their basic character is distinctive. An ungraded muddy sandstone interval is encased within mud‐poor graded sandstone, siltstone and mudstone. The muddy sandstone interval preserves evidence of en masse deposition and is thus termed a debrite. The mud‐poor sandstone, siltstone and mudstone show features indicating progressive layer‐by‐layer deposition and are thus called a turbidite. Palaeocurrent indicators, ubiquitous stratigraphic association and the position of hemipelagic intervals demonstrate that debrite and enclosing turbidite originate in the same event. Detailed field observations are presented for co‐genetic debrite–turbidite beds in three widespread sequences of variable age: the Miocene Marnoso Arenacea Formation in the Italian Apennines; the Silurian Aberystwyth Grits in Wales; and Quaternary deposits of the Agadir Basin, offshore Morocco. Deposition of these sequences occurred in similar unchannellized basin‐plain settings. Co‐genetic debrite–turbidite beds were deposited from longitudinally segregated flow events, comprising both debris flow and forerunning turbidity current. It is most likely that the debris flow was generated by relatively shallow (few tens of centimetres) erosion of mud‐rich sea‐floor sediment. Changes in the settling behaviour of sand grains from a muddy fluid as flows decelerated may also have contributed to debrite deposition. The association with distal settings results from the ubiquitous presence of muddy deposits in such locations, which may be eroded and disaggregated to form a cohesive debris flow. Debrite intervals may be extensive (> 26 × 10 km in the Marnoso Arenacea Formation) and are not restricted to basin margins. Such long debris flow run‐out on low‐gradient sea floor (< 0·1°) may simply be due to low yield strength (? 50 Pa) of the debris–water mixture. This study emphasizes that multiple flow types, and transformations between flow types, can occur within the distal parts of submarine flow events.     

Nuclear Waste Disposal Simulations: Couplex Test Cases

We give some results obtained for the Couplex test cases proposed by the ANDRA. In this paper our aim is twofold. Firstly, to compute the release of nuclides out of the repository by concentrating on the 3D near field (Couplex 2). The simulation of the transport phenomena takes into account the dissolution of the glass containers and congruent emissions of the radio-nuclides including filiation chains and some simplified chemistry. Secondly, it is to use the near field computations in order to simulate the nuclide migrations in a 2D far field (Couplex 3). Coupling in between the two simulations takes into consideration the periodicity of the disposal modules and the geometry of the repository described in Couplex 1. The mixed finite element and discontinuous Galerkin methods are used to solve the convection–diffusion equations. In order to handle the nonlinear precipitation/dissolution term, we developed a new iterative technique that combines Picard and Newton–Raphson methods.     

Magnetic fabrics and rock magnetism of Proterozoic dike swarm from the southern São Francisco Craton, Minas Gerais State, Brazil

Magnetic fabric and rock magnetism studies were performed on 32 mafic dikes of a Proterozoic dike swarm from the southern São Francisco Craton (SFC; Minas Gerais State, SE Brazil). Magnetic anisotropies were determined by applying anisotropy of low-field magnetic susceptibility (AMS) and anisotropy of remanent magnetization (ARM). The latter was performed imposing both anhysteretic (total (AAR) and partial pAAR)) and isothermal remanence magnetizations (AIRM). Partial anhysteretic remanence anisotropy was performed based on remanent coercivity spectra from a pilot specimen of each site. In most sites, AMS is dominantly carried by ferromagnetic minerals, however, in some sites, the paramagnetic contribution exceeds 70% of bulk susceptibility. Rock magnetism and thin section analysis allow classifying the dikes as non-hydrothermalized and hydrothermalized. Magnetic measurement shows that the mean magnetic susceptibility is usually lower than 5×10⁻³ (SI). Ti-poor titanomagnetites up to pure magnetite pseudo-single-domain (PSD) grain sizes carry the majority of magnetic fabrics for non-hydrothermalized dikes whereas coarse to fine grained Ti-poor titanomagnetites carry the majority of magnetic fabrics for hydrothermalized dikes.Three primary AMS fabrics are recognized which are coaxial with ARM fabric, except for two dikes, from both non-hydrothermalized and hydrothermalized dikes. Normal AMS fabric surprisingly is not dominant (31%). The parallelism between AMS, pAAR_0–30, pAAR_30–60 and pAAR_60–90 fabrics in the hydrothermalized dikes indicates that magnetic grains formed due to late-stage crystallization or to remobilization of iron oxides due to hydrothermal alteration after dike emplacement have acquired a mimetic fabric coaxial with the primary fabric given by coarse-grained early crystallized Ti-poor titanomagnetites. This fabric is interpreted as magma flow in which the analysis of K_max inclination permitted the inference that the dikes were fed by horizontal or subhorizontal fluxes (K_max<30°). Intermediate AMS fabric is the most important (41%) in the investigated swarm. It is interpreted as due to vertical compaction of a static magma column with the minimum stress along the dike strike. ARM determinations for these sites also remained intermediate except for two dikes. In one of them, AIRM fabric resulted in normal AMS fabric while for the other AAR fabric resulted in inverse AMS fabric. A combination of AMS and ARM fabrics suggest that magmatic fabric for both dikes were overprinted by some late local event, probably related to Brasiliano orogenic processes after dike emplacement. InverseInverse AMS fabric is a minority (four dikes). ARM determinations also remained inverse suggesting a primary origin for inverse AMS fabric.     

Curie Point Depths Beneath Precordillera Cuyana and Sierras Pampeanas Obtained from Spectral Analysis of Magnetic Anomalies

A gravity and magnetic survey has been carried out with the purpose of investigating geophysical features of the crusts beneath three geological provinces in western Argentina: Cuyo Precordillera, the Sierras Pampeanas of San Juan and La Rioja, and Famatina System, the results of which are displayed in three maps: Bouguer anomaly, total field magnetic anomaly and total field reduced to the pole.

The top and bottom boundaries of the magnetized crust were calculated from power-density spectra of the total-field anomalies from our terrestrial database in 90 2D windows. The depths obtained for the bottom of magnetized crust are assumed to correspond to Curie point depths. The values thus obtained for the Precordillera range between 29 and 40 km, whereas for the Sierras Pampeanas, in the Sierra de Pie de Palo, and other mountain chains along the Bermejo-Desaguadero lineament or Valle Fértil lineament, such depth ranges between 20 and 35 km. These results are consistent with Curie point depths determined on different continental regions in the world.

A map of regional heat flow has been prepared in the present work based on the depth of the Curie point isotherm, which shows that heat flow patterns in Precordillera are different from those found in Sierras Pampeanas.

A significant heat flow extending in Northeast-Southwest direction seems to be directly related to Juan Fernández Ridge trace.

The results of the present investigations also point out a possible relationship between the base of the magnetized crust and the boundary separating the brittle from the ductile crustal regime.     

Rainfall induced debris flows in pyroclastic deposits, Campania (southern Italy)

A combination of empirical and physically based hydrological models has been used to analyze historical data on rainfall and debris-flow occurrence in western Campania, to examine the correlation between rainfall and debris-flow events.

Rainfall data from major storms recorded in recent decades in western Campania were compiled, including daily series from several rain gauges located inside landslide areas, supplemented by hourly rainfall data from some of the principal storms.

A two-phase approach is proposed. During phase 1, soil moisture levels have been modelled as the hydrological balance between precipitation and evapotranspiration, on a daily scale, using the method of Thornthwaite [Geograph. Rev. 38 (1948) 55].

Phase 2 is related to the accumulation of surplus moisture from intense rainfall, leading to the development of positive pore pressures. These interactions take place on an hourly time scale by the “leaky barrel” (LB) model described by Wilson and Wiezoreck [Env. Eng. Geoscience, 1 (1995) 11]. In combination with hourly rainfall records, the LB model has been used to compare hydrological effects of different storms. The critical level of retained rain water has been fixed by the timing of debris-flow activity, related to recorded storm events.

New rainfall intensity–duration thresholds for debris-flow initiation in western Campania are proposed. These thresholds are related to individual rain gauge and assume a previously satisfied field capacity condition. The new thresholds are somewhat higher than those plotted by previous authors, but are thought to be more accurate and thus need less conservatism.