确定砂土动剪切模量和阻尼比的方法对比

确定土体动剪切模量的常用方法有规范法、Kumar法和自相关函数法,确定相应阻尼比的方法有规范法、Das and Luo法、Kokusho法、Kumar法和互相关函数法,为了分析不同方法所产生差异,实现定量化对比分析,笔者以福建标准砂（粒径为0.5~1.0 mm）为研究对象,采用不排水的应力控制动三轴试验,探讨不同的确定土体动剪切模量和阻尼比方法的差异性,并给出了不同土体条件建议选用的方法。结果表明：1）3种方法确定动剪切模量的结果有一定的差异,随剪应变的增大结果的差异逐渐增大,有效围压对结果的差异性有所影响,当剪应变为4×10^-3,有效围压为100 kPa时,3种方法差异显著,相对误差最大接近20%;2）而5种方法确定阻尼比的结果差异显著,随着剪应变的增大,5种方法确定的阻尼比相对误差大体上均在迅速减小,只有规范法在有效围压为100 kPa时,其相对误差有较小的增大趋势;5种方法中,Kumar法确定的阻尼比最接近平均阻尼比,互相关函数法远高于平均阻尼比,Das and Luo法和Kokusho法确定的阻尼比基本一致但低于平均阻尼比。建议以后的工程应用中,加载方式为应力控制时,可采用自相关函数法确定动剪切模量,采用Kumar法确定阻尼比,二者确定的动剪切模量和阻尼比均最接近平均值。     

抗浮锚杆应力-应变状态的线弹性理论分析

假定抗浮锚杆各部分贡献的位移与锚杆轴力均呈线弹性关系,运用力学原理分析锚杆轴力与锚侧摩阻力、锚-土变形之间的相互关系,推导出锚杆的摩阻力、轴力及各部分变形与锚杆各参数的相互关系。实例验证结果表明：基于线弹性模型基础上建立的摩阻力、轴力和位移公式能够较好地描述垂向抗浮锚杆在弹性变形阶段的内力和变形形态;获得了抗浮锚杆摩阻力和剪切位移沿锚固长度的分布规律;证实了锚土界面处变形为土层抗浮锚杆变形的主要部分。     

结构性参数在黄土地基沉降计算中的应用研究

弦线模量法建立了考虑黄土基本物性指标及附加应力综合影响的弦线模量函数,应用分层总和法计算黄土地基的变形量,并在陕西关中黄土地区工程实践中获得良好的预测结果,而在分析兰州等其他黄土地区地基沉降时,结果出现偏差,究其原因,与计算中忽视了天然状态下黄土的结构性特征有关。以弦线模量法为基础,通过西安近郊4处土样试验和大量载荷试验资料,分析黄土的构度指标与压缩模量、孔隙比、含水量的关系,并将构度指标引入弦线模量表,深化结构性参数在地基沉降变形计算中的理论。     

测井资料Xu-White模型预测横波速度的一些新观点

目前横波预测的方法大致可以分为两种:经验公式预测和理论岩石物理模型。由于经验公式预测一般具有区域性,研究者更重视岩石物理模型预测。目前大多数岩石物理模型预测横波的方法假定地下流体的物性参数(速度和密度)不受地层深度的影响,且孔隙扁率是恒定的,实际上这并不科学。因为矿物的体积模量和剪切模量随所处地层深度发生改变,而对于孔隙扁率则随颗粒形状、孔隙度等的变化有较大变化。针对这些情况,提出一种新的改进的Xu-White横波预测方法,并可取得较好的效果。     

基于土壤侵蚀遥感调查的河流输沙量的计算

河流泥沙来量的计算是工程水文计算的一个重要组成部分。有水文站观测资料的地方,输潲星的计算比较容易。而对于没有水文站分布或观测资料不足的边远地区,用常规无法计算出输沙星。     

南海神狐海域水合物三相混合层测井评价方法研究

天然气水合物降压试采过程中,水合物、游离气和水的三相混合层中的游离气首先被采出,从而提高降压效率,促进水合物分解;因此利用岩心刻度测井的方法开展南海神狐海域水合物三相混合层测井评价方法研究,对水合物矿体储量计算以及产业化开采具有重要意义.三相混合层与水合物层相比,其密度和中子孔隙度值均减小,纵波速度明显下降;与气层相比...     

重载铁路水泥改良膨胀土路基填料动弹模量及阻尼比研究

动弹模量与阻尼比是土动力学分析中的重要力学参数,考虑重载铁路荷载特征定量分析水泥改良膨胀土的动模量和阻尼比的较少。依托蒙西至华中地区铁路煤运通道(简称蒙-华铁路)工程为背景,采用南阳邓州市大山寨膨胀土,通过在不同频率、围压、固结比及动应力幅值下的持续振动三轴试验,研究了水泥掺量3%和5%水泥改良膨胀土的动弹模量及阻尼比,并与膨胀土素土进行对比分析。结果表明:水泥掺量3%和5%改良膨胀土的最大动弹模量约为膨胀土素土的3~4倍;在动弹模量-应变曲线中,动应变小于0. 002时表现为陡降段,动弹模量随动应变增长降幅达70%,而动应变大于0. 002时降幅较小,动弹模量随动应变增长趋于稳定;动弹模量随围压、频率、水泥掺量增加而增大,阻尼比随围压、固结比增加而减小;低应变水平下,固结比与动模量成正相关关系,高应变水平下,固结比与动弹模量成负相关关系。同时,对动弹模量及阻尼比进行了归一化分析,建立了估算动弹模量及阻尼比的经验公式。     

DUT-1合成模型冰的弯曲强度和弹性模量实验分析

依据渤海海冰物理和力学特征值和国内水池实验室能力,以1:10～1:30比尺要求,发展了DUT-1合成模型冰.文中简介该模型冰的理想参数、成分和制备过程.就其弯曲强度和弹性模量进行系统的实验分析.通过500多次弯曲实验,获得该模型冰在不同加载速度下的破坏方式,各向同性证据和弯曲强度为35～65kPa和弹性模量平均53MPa的结果.并且得到弯曲强度和弹性模量在实测湿密度范围内呈递增关系,浸水模型冰性能稳定时间超过4h,弹性模量与弯曲强度之比82%超过2000.     

Laboratory and field performance of recycled aggregate base in a seasonally cold region

The objective of this project was to characterize the freeze-thaw properties of recycled concrete (RCA) and asphalt (RAP) as unbound base and to assess how they behaved in the field for nearly 8 years. This paper includes an examination of existing information, laboratory studies of freeze-thaw behavior, and evaluation of data from MnROAD field-test sections in a seasonally cold region, i.e., in Minnesota, USA. Test sections were constructed using recycled materials in the granular base layers at the MnROAD test facility. One test section included 100% RAP, another 100% RCA, a third one a 50/50 blend of RCA/natural aggregate, and a fourth one only natural aggregate (Class 5) as a control. The stiffness (i.e., elastic modulus) was monitored during construction and throughout the pavement life by the Minnesota Department of Transportation, along with the variation of temperatures and moisture regimes in the pavement to determine their effects on pavement performance. The resilient modulus of each material was determined by bench-scale testing in accordance with NCHRP 1-28a, as well as by field-scale tests incorporating a falling-weight deflectometer. Specimens were subjected to as many as 20 cycles of freeze-thaw in the laboratory, and the change in their resilient modulus was measured. In the field-test sections constructed with the same materials as the base course, temperature, moisture, and field modulus (from falling-weight deflectometer tests) were monitored seasonally for nearly 8 years. From the temperatures in the base course layer, the number of freeze-thaw cycles experienced in the field was determined for each test section. Inferences were made relative to modulus change versus freeze-thaw cycles. Conclusions were drawn for long-term field performances of the recycled base (RAB) in comparison to natural aggregate.     

Stress‐dependent elastic wave velocity of microfractured sandstone

A model for the stress‐dependent elastic wave velocity response of fractured rock mass is proposed based on experimental evidence of stress‐dependent fracture normal and shear stiffness. Previously proposed models and previous experimental studies on stress‐dependent fracture stiffness have been reviewed to provide a basis for the new model. Most of the existing stress‐dependent elastic wave velocity models are empirical, with model parameters that do not have clear physical meanings. To propose the new model, the rock mass is assumed to have randomly oriented microscopic fractures. In addition, the characteristic length of microfractures is assumed to be sufficiently short compared to the rock mass dimensions. The macroscopic stress‐dependent elastic wave velocity response is assumed to be attributed to the stress dependency of fracture stiffness. The stress‐dependent fracture normal stiffness is defined as a generalized power law function of effective normal stress, which is a modification of the Goodman's model. On the other hand, the stress dependency of fracture shear stiffness is modeled as a linear function of normal stress based on experimental data. Ultrasonic wave velocity responses of a dry core sample of Berea sandstone were tested at effective stresses ranging from 2 to 55 MPa. Visual observation of thin sections obtained from the Berea sandstone confirms that the assumptions made for microstructure of rock mass model are appropriate. It is shown that the model can describe the stress‐dependent ultrasonic wave velocity responses of dry Berea sandstone with a set of reasonable material parameter values. Published 2013. This article is a U.S. Government work and is in the public domain in the USA.