Stability analysis of tunnels driven in jointed rocks by means of a homogenized limit analysis approach

Conceived as a potential alternative to the classical design methods employed for analyzing the stability of underground structures driven in jointed rocks, the homogenization approach stems from the heuristic idea that, from a macroscopic point of view, a rock mass cut by a network of joints may be perceived as a homogenized continuum. The strength properties of the latter can be theoretically obtained from the failure conditions of its individual constituents: rock matrix and joint interfaces. At the material level, the limit analysis reasoning is used in the context of homogenization to formulate the homogenized strength criterion of a jointed rock mass in the particular situation of a single set of parallel joints. As it could be expected, the obtained closed‐form expressions show the strength anisotropy induced by joint preferential orientation. The support functions (π functions) associated with the homogenized strength criterion are also determined in both plane strain and three‐dimensional cases. This criterion is then applied to the investigation of stability analysis of a tunnel excavated in a jointed rock mass. Upper bounds estimated of the stability factor are derived from the implementation of the kinematic approach directly on the homogenized underground structure. Finally, the approach is applied to analyze and discuss the collapse of the Pinheiros subway station (São Paulo, Brazil). Copyright © 2014 John Wiley & Sons, Ltd.     

Mechanical transitional behavior of binary mixtures via DEM: Effect of differences in contact-type friction coefficients

This report presents a numerical investigation of the shear behavior of binary mixtures via a two-dimensional discrete element method. The effect of the coarse particle content on the peak shear strength of mixtures is investigated for different contact-type friction coefficients. A detailed analysis on the anisotropies enables us to understand the microscopic mechanisms that result in the dependency of the peak shear strengths on the coarse particle content. The contributions of different contact types to the peak shear strength are quantified. Lastly, the inter-particles structures are examined when the binary mixtures become coarse-particle-supported structures.     

From soil aggregates to riverine flocs: a laboratory experiment assessing the respective effects of soil type and flow shear stress on particles characteristics

Particles eroded from hillslopes and exported to rivers are recognized to be composite particles of high internal complexity. Their architecture and composition are known to influence their transport behaviour within the water column relative to discrete particles. To‐date, hillslope erosion studies consider aggregates to be stable once they are detached from the soil matrix. However, lowland rivers and estuaries studies often suggest that particle structure and dynamics are controlled by flocculation within the water column. In order to improve the understanding of particle dynamics along the continuum from hillslopes to the lowland river environment, soil particle behaviour was tested under controlled laboratory conditions. Seven flume erosion and deposition experiments, designed to simulate a natural erosive event, and five shear cell experiments were performed using three contrasting materials: two of them were poorly developed and as such can not be considered as soils, whilst the third one was a calcareous brown soil. These experiments revealed that soil aggregates were prone to disaggregation within the water column and that flocculation may affect their size distribution during transport. Large differences in effective particle size were found between soil types during the rising limb of the bed shear stress sequence. Indeed, at the maximum applied bed shear stress, the aggregated particles median diameter was found to be three times larger for the well‐developed soil than for the two others. Differences were smaller in the falling limb, suggesting that soil aggregates underwent structural changes. However, characterization of particles strength parameters showed that these changes did not fully turn soil aggregates into flocs, but rather into hybrid soil aggregate–floc particles. Copyright © 2013 John Wiley & Sons, Ltd.     

Displacement velocity effects on rock fracture shear strengths

Triaxial shear tests are performed to assess the effects of displacement velocity and confining pressure on shear strengths and dilations of tension-induced fractures and smooth saw-cut surfaces prepared in granite, sandstone and marl specimens. A polyaxial load frame is used to apply confining pressures between 1 and 18 MPa with displacement velocities ranging from 1.15 × 10⁻⁵ to 1.15 × 10⁻² mm/s. The results indicate that the shearing resistances of smooth saw-cut surfaces tend to be independent of the displacement velocity and confining pressure. Under each confinement the peak and residual shear strengths and dilation rates of rough fractures increase with displacement velocities. The sheared-off areas increase when the confining pressure increases, and the displacement rate decreases. The velocity-dependent shear strengths tend to act more under high confining pressures for the rough fractures in strong rock (granite) than for the smoother fractures in weaker rocks (sandstone and marl). An empirical criterion that explicitly incorporates the effects of shear velocity is proposed to describe the peak and residual shear strengths. The criterion fits well to the test results for the three tested rocks.     

SAR影像与光学影像的高斯伽玛型边缘强度特征匹配法

提出了一种基于影像边缘强度图描述的SAR影像与光学影像匹配方法。首先对影像进行粗纠正,消除影像之间的尺度和旋转变化;其次,改进相位一致性特征检测方法,提取对影像相干斑噪声稳健的特征点;然后基于高斯伽玛型双边窗口比值算子计算影像边缘强度图,在此基础上构造不变特征描述符;最后联合几何约束条件,实现SAR影像与光学影像匹配。试验结果证明,与现有方法相比,本文方法能够大幅提高SAR影像与光学影像匹配结果中的正确匹配特征数量以及影像配准精度。     

The Carrancas Formation,Bambuí Group: A record of pre-Marinoan sedimentation on the southern São Francisco craton,Brazil

The Carrancas Formation outcrops in east-central Brazil on the southern margin of the São Francisco craton where it comprises the base of the late Neoproterozoic Bambuí Group. It is overlain by the basal Ediacaran cap carbonate Sete Lagoas Formation and was for a long time considered to be glacially influenced and correlative with the glaciogenic Jequitaí Formation. New stratigraphic, isotopic and geochronologic data imply that the Carrancas Formation was instead formed by the shedding of debris from basement highs uplifted during an episode of minor continental rifting. Reddish dolostones in the upper Carrancas Formation have δ¹³C values ranging from +7.1 to +9.6‰, which is a unique C isotopic composition for the lowermost Bambuí Group but similar to values found in the Tijucuçu sequence, a pre-glacial unit in the Araçuaí fold belt on the eastern margin of the São Francisco craton. The stratigraphic position below basal Ediacaran cap carbonates and the highly positive δ¹³C values together indicate a Cryogenian interglacial age for the Carrancas Formation, with the high δ¹³C values representing the so-called Keele peak, which precedes the pre-Marinoan Trezona negative δ¹³C excursion in other well characterized Cryogenian sequences. Hence, The Carrancas Formation pre-dates de Marinoan Jequitaí Formation and represents an interval of Cryogenian stratigraphy not previously known to occur on the southern margin of São Francicso craton. Documentation of Cryogenian interglacial strata on the São Francisco craton reinforces recent revisions to the age of Bambuí Group strata and has implications for the development of the Bambuí basin.     

基于峰值因子最大化的鬼波压制方法

针对传统拖缆采集得到的海上地震资料受鬼波影响而导致频带宽度变窄,笔者提出一种去鬼波方法,可以压制鬼波效应,拓宽频带。首先在频率-空间域推导出镜像数据生成公式,并基于峰值因子最大化的参数搜索方法来估计最优的鬼波延迟时间,将最优的鬼波延迟时代入镜像记录生成公式,获得最优的镜像记录,利用联合反褶积算法得到最优的去鬼波结果。将本文中的方法应用于模拟的变深度采集数据和海上实测的变深度采集数据,证实该方法可以有效地压制鬼波,消除频谱中的陷波点,得到宽频数据。     

层状边坡滑动边界强度参数取值方法研究

滑坡滑带土强度参数取值的准确性,决定了滑坡稳定性计算的可靠程度。因此获得准确、可靠的滑动边界强度参数至关重要。然而在实际情况中,由于取样位置试样的代表性,以及试样转运过程中保存条件的限制,现场所取得的滑带土在室内试验得到的强度参数已经不能完全反映真实环境下的抗剪强度。因此考虑软弱夹层、滑带土各种物理和力学指标间存在必然联系,并表现出特定的规律性,尝试通过试验,揭示指标间的关联规律,并建立了相关性好的关系式,据此评价滑动边界的抗剪强度参数。     

Residual compressive strength of inclined steel tubular members with local corrosion

In jacket-type offshore structures, corrosion damage affects the structural performance under compressive loading, which is created by the working and design loads of the main system. In this study, the effects of corrosion damage on the compressive structural behavior and strength of steel tubular members were investigated. Artificial corrosion damage was applied to the tubular specimens via mechanical processing and hand drilling to replicate the inclined nature of jacket-type offshore structures. The damage was applied to either half or all of the circumference of the specimens. The compressive failure modes of the artificially corroded tubular members were affected by the corrosion conditions. The compressive strengths were also affected by the level of corrosion. From the results of this study, the residual compressive strengths of corroded tubular steel members can be estimated based on the condition of the damaged sectional areas.