少筋混凝土重力式桥墩抗震研究现状

我国铁路桥梁普遍采用少筋混凝土重力式桥墩（配筋率<0.5%）,现有普通钢筋混凝土结构的延性抗震理论不适用于该类型桥墩。为了促进我国铁路重力式桥墩抗震理论的发展,详细论述了我国少筋混凝土重力式桥墩的研究现状和存在问题。首先,对少筋混凝土重力式桥墩的破坏特征及破坏机理进行了总结;其次,分析了各参数对少筋混凝土重力式桥墩抗震性能的影响;再次,对目前少筋混凝土重力式桥墩的抗震设计方法进行了汇总与分析;最后,对少筋混凝土重力式桥墩的数值分析模型进行了归纳与分析。通过对现有研究的汇总发现:目前对少筋混凝土重力式桥墩的试验研究主要以拟静力方法为主,还缺少振动台试验研究其动力状态下的破坏机理及抗震性能;少筋混凝土重力式桥墩的破坏机理及其与各影响因素之间的定量关系还不明确;已提出的少筋混凝土重力式桥墩的抗震设计方法存在塑性铰区计算不合理等问题,还需要进一步的完善。为少筋混凝土重力式桥墩抗震研究提供了方向。     

山顶建筑场地稳定性分析评价与边坡治理

在山顶建设大型建筑主要岩土工程问题是场地稳定性问题,本文通过某工程实例,分析了场地存在沿倾斜层面整体滑动、沿裂隙和层面局部滑动、块状风化岩覆盖层滑动、岩块崩塌及表层危岩、危石滚落等破坏型式,通过室内和现场剪切试验取得的结构面强度参数,对山顶边坡稳定性进行了常规方法和有限元法的定量评价,得出场地整体稳定性和局部稳定性满足要求的结论,对岩块崩塌和危岩危石滚落采取喷锚支护措施,本工程取得的经验对于类似工程具有指导意义。     

坑式钢管静压桩在地基加固中的应用

坑式钢管静压桩是解决既有建筑物因软弱土层地基产生沉降变形的一种技术方法。针对山西北化关铝化工有限公司质检楼地基沉降变形及工程地质条件,提出了采用坑式钢管静压桩进行加固处理的设计方案,介绍了坑式钢管静压桩施工方案和施工流程及注意事项;总结了施工过程中遇到的问题,并对施工后的监测数据进行了分析。结果表明,坑式钢管静压桩施工对软弱地基加固效果良好,可成功地解决软弱土层产生的地基沉降开裂问题。     

Transient loading-related settlement of a square foundation on geogrid-reinforced sand

Summary Laboratory model test results are presented that determine the effectiveness of using layers of geogrids as reinforcement in sand to reduce the settlement of square surface foundations subjected to transient loading. The model tests were conducted with only one type of geogrid at one relative density of compaction of sand. The maximum intensity of the transient load applied always exceeded the static ultimate bearing capacity of the foundation when supported by unreinforced sand. The settlement reduction factors for various depths of reinforcement have been determined.     

预应力锚索技术在大型水库除险加固工程中的应用

介绍了无粘结预应力锚固技术在吉林省二龙山水库除险加固工程中的应用。对造孔、编索、下索、张拉等工艺进行了详细介绍。     

微型钢管灌注桩基础托换技术

为解决既有建筑基础加固工程中有限的施工空间和成本控制问题,研究采用了微型钢管灌注桩基础托换技术,实践表明,该技术是一种实用可行的施工方法。介绍了微型钢管灌注桩基础托换技术的机理及施工工艺,并通过工程实例阐明了该技术的可行性和有效性。     

管壁开孔足尺钢管混凝土柱抗震性能试验研究

针对钢筋混凝土梁与钢管混凝土柱的穿筋连接形式,研究了钢管开穿筋小孔及加固对钢管混凝土柱抗震性能的影响。对于未开孔、开孔和开孔并加固三种情况,进行了3个直径为610 mm的足尺钢管混凝土柱试件的低周反复荷载试验。试验结果表明:未开孔试件在距根部100 mm处发生钢管屈曲破坏;开孔试件的破坏主要是开孔处屈曲撕裂,开孔对钢管混凝土柱初期刚度和峰值承载力影响不大,但在峰值承载力后受孔边撕裂破坏影响,开孔试件的刚度和强度退化较快、延性和耗能能力降低;开孔并加固试件的破坏位置上移至加固段上部约90 mm处,与未开孔试件表现出相似的抗震性能。     

富水破碎岩体注浆加固材料试验研究与应用

针对富水破碎地层注浆治理过程中传统水泥类材料难以实现注浆加固和堵水同步进行的难题,以硫铝酸盐水泥熟料和钢渣微粉为主要原材,成功制备了一种水泥基复合注浆材料（CGM）。通过与传统水泥材料进行性能对比试验,采用扫描电镜和X射线测试手段,分析了CGM材料制备工艺、组分含量和浆液制备条件对材料性能的作用规律,并检验了CGM材料的工程适用性。结果表明：CGM材料宜采用混合粉磨制备工艺,可显著提高其水化活性,且粉磨时间应不超过45 min。钢渣微粉含量越高,水灰比越大,结石体强度越低,凝结时间越长,水灰比超过1.2:1时,结石体后期会出现干缩。与传统水泥材料相比,CGM材料浆液凝结时间与黏度的环境敏感度低,具有显著的工程适用性和性能优越性。     

A Probabilistic Model for Fatigue Crack Propagation Analysis

A simple probabilistic model for predicting crack growth behavior under random loading is pre-sented.In the model,the parameters c and m in the Paris-Erdogan Equation are taken as random variables,and their stochastic characteristic values are obtained through fatigue crack propagation tests on an offshorestructural steel under constant amplitude loading.Furthermore,by using the Monte Carlo simulation tech-nique,the fatigue crack propagation life to reach a given crack length is predicted.The tests are conducted toverify the applicability of the theoretical prediction of the fatigue crack propagation.     

Displacement amplification factors for steel eccentrically braced frames

Inelastic deformation capacity of links is a factor that significantly influences design of steel eccentrically braced frames (EBFs). The link rotation angle is used to describe inelastic link deformation. The link rotation angle is generally calculated by making use of design story drifts that in turn are calculated by modifying the elastic displacements by a displacement amplification factor. This paper presents a numerical study undertaken to evaluate the displacement amplification factor given in ASCE7‐10 for EBFs and the rigid‐plastic mechanism used for calculating link rotation angles. A total of 72 EBFs were designed by considering the number of stories, the bay width, the link length to bay width ratio, and the seismic hazard level as the prime variables. All structures were analyzed using elastic and inelastic time history analyses. The results indicated that the displacement amplification factor given in ASCE7‐10 provides unconservative estimates of the story drifts. On the other hand, the rigid‐plastic mechanism provides conservative estimates of link rotations. Based on the results of the numerical study, a new set of displacement amplification factors that vary along the height of the structure and modifications to the rigid‐plastic mechanism were developed. In light of the proposed modifications, the EBFs were redesigned and analyzed using inelastic time history analysis. The results indicated that the proposed modifications provide improvements for the displacement amplification factor and link rotation angle calculation procedures. Copyright © 2014 John Wiley & Sons, Ltd.