水平定向钻进铺管技术在盐碱地改良中的应用

土壤盐碱化作为一种渐进性环境地质灾害,已严重制约着人类生活与社会经济的发展,对盐碱地实施改良和微咸水开发利用已成为世界关注的热点。以往的盐碱地改良多用明渠、暗管排水、暗管结合大口径竖井抽排、种植耐碱性植物等方法,明渠及埋设暗管对地表的开挖破坏性极大、且排水量及适用深度有限、植物改良存在周期长、费时费力等诸多缺点。水平定向钻进铺管技术可将滤水管以水平或近似水平安装在含水层中（水平井）,可垂直于含水层流向长距离铺设,与传统改良方式相比能获得较大的出水量、成本低、且施工对环境影响小等诸多优势,工程实例证明,该施工工艺技术为盐碱地改良、地下咸水开发利用、浅层低渗透性地下水资源开采等提供了较理想的工艺方法。     

定向钻进敷设电缆保护管轨迹优化设计研究

在老旧城区内采用定向钻进敷设地下管线,常常需要从已有的各类地下建（构）筑物或管线下方穿过,方案设计时就应考虑新建管道与之安全距离的取值问题。以厦门市某110 kV电力电缆的定向钻进工程的实际需求为出发点,在对国内现有规程规范及工程实例调查的基础上,对电力电缆保护管定向钻进敷设安全距离取值的影响因素进行分析,优化工程定向钻进敷设方案,指导该工程的建设,并为类似工程建设提供参考。     

混凝土灌注桩桩头渗水的处理及预防措施

混凝土灌注桩桩头渗水对桩体混凝土受力和基底防水产生影响,对混凝土结构中的钢筋造成腐蚀。结合工程实例,对桩头渗水产生的原因进行分析,主要有操作经验不足、责任心不强,灌注器具不合格,混凝土质量指标不符合要求,灌注接近结束时拔管速度过快、灌注终了超灌高度测量不准,基土含水量高、水压大等;出现桩头渗水可采用人工剔除或注浆封堵处理;介绍了预防措施,包括加强作业人员培训,强化灌注器具检查,严控混凝土质量,重点监管终灌时的状态,做好基坑内降水工作等。     

Residual compressive strength of inclined steel tubular members with local corrosion

In jacket-type offshore structures, corrosion damage affects the structural performance under compressive loading, which is created by the working and design loads of the main system. In this study, the effects of corrosion damage on the compressive structural behavior and strength of steel tubular members were investigated. Artificial corrosion damage was applied to the tubular specimens via mechanical processing and hand drilling to replicate the inclined nature of jacket-type offshore structures. The damage was applied to either half or all of the circumference of the specimens. The compressive failure modes of the artificially corroded tubular members were affected by the corrosion conditions. The compressive strengths were also affected by the level of corrosion. From the results of this study, the residual compressive strengths of corroded tubular steel members can be estimated based on the condition of the damaged sectional areas.     

锈蚀钢筋在疲劳荷载作用下压磁场分布研究

针对锈蚀钢筋的疲劳损伤与寿命评估中的难度大、精度低等问题,引入压磁检测技术,对锈蚀钢筋疲劳过程中的压磁场分布进行检测,从宏观与微观相结合的角度分析压磁场分布与疲劳损伤之间的联系。试验结果表明,锈蚀钢筋的压磁场分布能够反映疲劳损伤的演变规律,疲劳后期非线性特征加剧,锈蚀率及应力幅越大则变化越为明显,磁感强度值、磁场分布梯度、"反转"现象等均有助于进行疲劳损伤评价与寿命预测。研究结果可为压磁无损检测技术在钢筋混凝土结构中的应用提供依据。     

桩锚支护深基坑施工过程变形特征分析

以济南市某大型深基坑工程为依托,通过FLAC3D对深基坑工程不同施工阶段的变形特性进行了数值计算分析;桩锚支护深基坑,地表最大竖向变行产生在距离基坑边缘10 m位置处,且最大竖向变形量为46.16 mm;最大水平位移发生在桩顶冠梁位置处,最大水平位移为53.45 mm,是基坑支护最薄弱环节,基坑呈现三角形状向内侧滑动的趋势。     

Failure Pressure Analysis of Corroded Moderate-to-High Strength Pipelines

Based on the elastic-plastic, large-deformation finite element method, burst capacity of steel pipeline with longitudinal corrosion defect subjected to internal pressure is studied. The appropriate stress-based criterion is used to predict the failure pressure of finite element model of corroded pipeline under internal pressure. By considering the pipe steel grades and geometries of corrosion defects, a series of finite element analyses is conducted. The effects of corrosion depth, length and width on burst capacity are also discussed. A specific failure pressure solution for the assessment of corrosion defects in moderate-to-high strength pipeline is proposed on the base of numerical results. The failure pressures predicted by the proposed method are in better agreement with the experimental results than the results by the other methods.     

腐蚀管道在内压和轴向压力影响下的弯曲破坏

运行在恶劣环境中的海底管道,往往受到内压、轴力和弯矩等复杂荷载的联合作用。腐蚀会导致管壁局部变薄,降低管道极限承载力。为保证管道安全高效运行,准确预测和分析复杂荷载作用下的塑性极限承载力和变形行为就显得尤为重要。考虑大应变和大变形、应力强化和材料非线性,运用数值仿真软件建立腐蚀缺陷管道的三维实体有限元模型,在全尺寸管道破坏试验验证的基础上,对腐蚀管道在内压、轴向压力和弯矩相互作用下的失效模式和极限弯矩承载力进行了相关研究,并进行了腐蚀缺陷几何参数的敏感性分析。研究结果表明:初始内压和初始轴向压力会显著降低腐蚀管道的极限弯矩承载力,并且影响最终的失效模式;在腐蚀缺陷几何尺寸参数中,腐蚀宽度比腐蚀深度和腐蚀长度的影响更大。     

Safety Assessment of Buried Pipeline during Pile Driving Vibration in Offshore Engineering

To assess the impact of pile driving on adjacent submarine pipelines during the reconstruction of a pier berth, the local damage model of submarine pipelines is established to explore the safety thresholds of the particle peak velocity and horizontal displacement. The results are analyzed and adjusted by the existing standards and the corresponding literatures. Then, a three-dimensional numerical model is presented to assess the feasibility of the construction of piles by the obtained safety limits, in which the nonlinear behavior of the soil and stress–seepage coupling analysis are considered. After the construction, the safety of submarine pipelines is rechecked by the measured value of the particle peak velocity and horizontal displacement. Meanwhile, the propagation law of vibration, the horizontal displacement of underground soil, and the pore pressure during pile driving are explored. The results indicate that the construction of piles of 2# mooring pier did not cause damage to adjacent submarine pipelines. However, the construction of piles of 1# mooring pier which is nearer may cause damage to submarine pipelines.     

Field Evaluation of the Vertical Bearing Capacity of a Screw Pretensioned Spun High-Strength Concrete Pile

This study has evaluated the vertical bearing capacity by conducting static load tests for noise-free and vibration-free screw pretensioned spun high-strength concrete (PHC) piles installed using two different methods (end-squirting shoe and pre-boring methods). Vertical bearing capacity differences seem to occur due to the displacement of soils near the external circumference of a pile, depending on the installation method. A method by which to evaluate the bearing capacity of screw concrete piles is suggested by considering the equations that already have been used to calculate the bearing capacity of piles. Based on static load tests and analysis, the pile installed using the end-squirting shoe method was assumed to be a bored pile and it was reasonable to use the equation proposed by the Japanese Geotechnical Society. At the same time, the pile installed using the pre-boring method was deemed a low soil displacement pile and so it was reasonable to apply the equations proposed for calculating the bearing capacity of the driven pile suggested by the Architectural Institute of Japan.