波浪作用下海床的有效应力分析

波浪作用下海床的稳定性分析是海洋工程地质评价的重要内容。海床的稳定性可通过计算分析其随时间变化的有效应力场来评估。本文建议了一个周期荷载作用下土体的本构模型 ,并用于计算波浪作用下海床的应力与变形。采用Biot固结理论和有限单元法 ,分析了海床的动态应力场与孔隙水压力场。波浪作用下两种渗透系数时有效应力的动态变化过程结果对比 ,反映了渗透消散作用对海床有效应力变化的影响     

深圳河河口围垦对防洪和河床冲淤影响研究

为研究深圳河河口福田保税区围垦填土占用部分河道对深圳河治理工程的影响 ,建立了贴体坐标系下平面二维的深圳河河道 -河口 -海湾整体水域的水流泥沙数学模型 ,计算了不同频率洪峰流量和河口潮位过程组合下河口围垦所造成的深圳河沿程水位抬高程度和河床冲淤变化情况 ,提出了建议的挖除方案     

Circulation and Brackish Water Dispersal in a Coastal Lagoon of Southwest Taiwan

Modest observations and numerical experiments were conducted to investigate circulation and brackish water dispersal in a coastal lagoon southwest of Taiwan. The Chi-Ku Lagoon, partially shielded from the sea by a string of sandbar barriers with two entrances among them, receives modest and episodic runoff from Chi-Ku Stream. Flood and ebb tidal streams entering and leaving the two entrances are found to converge and diverge in a flow stagnation area inside the lagoon. Under weak wind conditions, brackish water is preferentially retained in the flow stagnation area. Besides the observations, scenario runs using a three-dimensional numerical model also indicate strong modulation by monsoon winds. Both summer southwest monsoon and winter northeast monsoon reduce brackish water retention; the latter is found to be more effective. This revised version was published online in August 2006 with corrections to the Cover Date.     

A new efficient 3D non-hydrostatic free-surface flow model for simulating water wave motions

A new three-dimensional, non-hydrostatic free surface flow model is presented. For simulating water wave motions over uneven bottoms, the model employs an explicit project method on a Cartesian the staggered gird system to solve the complete three-dimensional Navier–Stokes equations. A bi-conjugated gradient method with a pre-conditioning procedure is used to solve the resulting matrix system. The model is capable of resolving non-hydrostatic pressure by incorporating the integral method of the top-layer pressure treatment, and predicting wave propagation and interaction over irregular bottom by including a partial bottom-cell treatment. Four examples of surface wave propagation are used to demonstrate the capability of the model. Using a small of vertical layers (e.g. 2–3 layers), it is shown that the model could effectively and accurately resolve wave shoaling, non-linearity, dispersion, fission, refraction, and diffraction phenomena.     

Application of a two-dimensional depth-averaged hydrodynamic tidal model

A two-dimensional hydrodynamic model application to the San Francisco Bay was performed using the Boundary-Fitted HYDROdynamic model (BFHYDRO). The model forcing functions consist of tidal elevations along the open boundary and fresh water flows from the Delta Outflow. The model-predicted surface elevations compare well with the observed surface elevations at five stations in San Francisco Bay. Mean error in the model predicted surface elevations and currents are less than 7 and 9%, respectively. Correlation coefficients for surface elevations and currents are higher than 0.94 and 0.95, respectively. The amplitudes and phases of the principal tidal constituents at 24 tidal stations in San Francisco Bay, obtained from a harmonic analysis of a 90-day simulation compare well with the observed data. The predicted amplitude and phase of the M₂ tidal constituent at these stations are respectively within 8 cm and 8° of the observed data. Maximum errors in the K₁ harmonic amplitudes and phases are less than 3 cm and 7° respectively. The asymmetric diurnal and semi-diurnal tidal ranges and spring and neap tidal cycles of the surface elevations and currents are well reproduced in the model at all stations.     

Fast static correction methods for high-frequency multichannel marine seismic reflection data: A high-resolution seismic study of channel-levee systems on the Bengal Fan

Very high-frequency marine multichannel seismic reflection data generated by small-volume air- or waterguns allow detailed, high-resolution studies of sedimentary structures of the order of one to few metres wavelength. The high-frequency content, however, requires (1) a very exact knowledge of the source and receiver positions, and (2) the development of data processing methods which take this exact geometry into account. Static corrections are crucial for the quality of very high-frequency stacked data because static shifts caused by variations of the source and streamer depths are of the order of half to one dominant wavelength, so that they can lead to destructive interference during stacking of CDP sorted traces. As common surface-consistent residual static correction methods developed for land seismic data require fixed shot and receiver locations two simple and fast techniques have been developed for marine seismic data with moving sources and receivers to correct such static shifts. The first method – called CDP static correction method – is based on a simultaneous recording of Parasound sediment echosounder and multichannel seismic reflection data. It compares the depth information derived from the first arrivals of both data sets to calculate static correction time shifts for each seismic channel relative to the Parasound water depths. The second method – called average static correction method – utilises the fact that the streamer depth is mainly controlled by bird units, which keep the streamer in a predefined depth at certain increments but do not prevent the streamer from being slightly buoyant in-between. In case of calm weather conditions these streamer bendings mainly contribute to the overall static time shifts, whereas depth variations of the source are negligible. Hence, mean static correction time shifts are calculated for each channel by averaging the depth values determined at each geophone group position for several subsequent shots. Application of both methods to data of a high-resolution seismic survey of channel-levee systems on the Bengal Fan shows that the quality of the stacked section can be improved significantly compared to stacking results achieved without preceding static corrections. The optimised records show sedimentary features in great detail, that are not visible without static corrections. Limitations only result from the sea floor topography. The CDP static correction method generally provides more coherent reflections than the average static correction method but can only be applied in areas with rather flat sea floor, where no diffraction hyperbolae occur. In contrast, the average static correction method can also be used in regions with rough morphology, but the coherency of reflections is slightly reduced compared to the results of the CDP static correction method.     

A Sensitivity Analysis of the Waterline Method of Constructing a Digital Elevation Model for Intertidal Areas in ERS SAR scene of Eastern England

A sensitivity analysis of the waterline method of constructing a Digital Elevation Model (DEM) of an intertidal zone using remote sensing and hydrodynamic modelling is described. Variation in vertical height accuracy as a function of beach slope is investigated using a set of nine ERS Synthetic Aperture Radar (SAR) images of the Humber/Wash area on the English east coast acquired between 1992 and 1994. Waterlines from these images are heighted using a hydrodynamic tide-surge model and interpolated using block kriging. On 1:500 slope beaches, an average block height estimation standard deviation of 18–22 cm is achieved. This rises to 27 cm on 1:100 slope beaches, and 32 cm on 1:30 slope beaches. The average heighting error at different slopes is decomposed into components due to waterline heighting error, inadequate sensor resolution and interpolation inaccuracy. It is shown that, at 1:500 slope, waterline heighting error and interpolation inaccuracy are the main error sources, whilst at 1:30 slope, errors due to inadequate sensor resolution become dominant. The ability of the technique to generate intertidal DEMs for almost the entire coastal zone in a complete ERS SAR scene covering 100×100 km is demonstrated.