排土场土石混合体分形特征与抗剪强度特性研究

露天矿山剥离堆积的土石混合体颗粒尺度不一,且力学性质异常复杂。以西藏甲玛铜矿南坑排土场为研究对象,采用现场勘测的方法测定堆积体的粒度组成及其分布特征,开展室内重塑土样的固结排水三轴压缩试验,以分析土体屈服强度特性与剪胀性,以及抗剪强度参数的取值。研究结果表明,自排土台阶坡顶至坡底,土石混合体的土粒减少且块石增多,颗粒的平均粒径呈指数关系增大;土体的粒度分布具有显著的分形结构特征,随块石含量的增大,其粒度分形维数减小。块石含量不同的土样在偏差应力作用下均表征出压密、屈服、塑性流动破坏的剪切特性,且围压条件与块石含量是影响土体剪切变形的两个关键因素,低围压时增加块石含量,土体更易产生剪胀。摩尔库伦强度准则能客观反映土体屈服的现象及过程,随块石含量的增加,土体的黏聚力呈线性减小且内摩擦角呈指数增大。     

基于小波域高斯尺度混合模型的天气雷达图像高分辨率插值

采用可精确刻画雷达回波强度数据统计特征的小波域高斯尺度混合（GSM）模型作为雷达图像先验模型,进行天气雷达图像插值,在提高图像分辨率的同时有效重建降水回波中局部强回波值、小尺度变化细节等一些重要空间分布统计特征。分析和总结雷达回波强度数据小波频率域统计特点,建立小波域GSM模型;匹配天气雷达图像小波系数和GSM模型,利用贝叶斯理论估计更小尺度的小波系数,进行小波逆变换,完成高分辨率天气雷达图像插值。试验表明,该算法能从低分辨率图像中估计出高分辨率高频系数,且所利用的先验模型充分考虑降水数据本身的特点,可有效捕获降水回波结构的非高斯特征和局部相关特性,重建雷达图像中的局部变化细节。      

A three‐phase model for unsaturated soils

A comprehensive framework to define the constitutive behaviour of unsaturated soils is developed within the theory of mixtures applied to three‐phase porous media. Each of the three phases is endowed with its own strain and stress. Elastic and elastic–plastic constitutive equations are developed. Particular emphasis is laid on the interactions between the phases both in the elastic and plastic regimes. Nevertheless, the clear structure of the constitutive equations requires a minimal number of material parameters. Their identification is provided: in particular, it incorporates directly the soil–water characteristic curve. Crucial to the formulation is an appropriate definition of the effective stress. The coupled influence of this effective stress and of suction makes it possible to describe qualitatively many of the characteristic features observed in experiments, e.g. for normally consolidated soils, a plastic behaviour up to air entry followed by an elastic behaviour at increasing suctions, and, on the way back, an elastic behaviour, unless compression is applied in which case plastic collapse occurs. Copyright © 2000 John Wiley & Sons, Ltd.     

循环荷载下土石混合体力学特性野外试验研究

土石混合体是一种物理、力学性质非常复杂的不连续介质。以云南某高速公路土石混合体边坡为例,分别对选取的3个试验点进行了单调加载、循环加载一次及多次循环加载试验,获取了其相应的剪切位移-剪切应力关系曲线,并对其曲线特征进行分析研究。通过对试样三维滑动面的形态分析,指出由于土石混合体三维滑动面的不规则性,利用传统的二维计算方法难以得到较为准确的强度参数。基于三维极限平衡理论,提出了土石混合体水平推剪试样强度参数的三维数据计算方法。并利用该方法得到了研究区土石混合体的相应的强度参数及残余强度参数。     

罗布泊硫酸镁亚型卤水制取钾混盐工艺试验研究

研究目的在于探讨用罗布泊罗北凹地卤水制取硫酸钾混盐的一种新方法。设计要求在冬季生产备用卤水，至春、夏季与原卤水混合，用以改变罗北凹地生产卤水的成分，而不需要加入钾矿物就可以把卤水成分点在五元体相图中的位置调整到最佳蒸发点，后经蒸发及兑卤等流程生产出高质量的钾混盐，即可获得含杂质较低硫酸钾镁盐。采用罗北凹地冬季冻卤水与春、夏季卤水混合生产钾混盐，方案是可行的，生产成本亦较低。     

Numerical determination of the effective permeability coefficient of soil–rock mixtures using the numerical manifold method

The present study extends the numerical manifold method to investigate the effective permeability coefficient (k_eff) of soil–rock mixtures. The influence of rock content, rock size, rock shape, and rock blocks' major axis direction on k_eff is studied. The results show the following: (1) k_eff decreases as the rock content increases; (2) the influence of rock size on k_eff can be neglected if other parameters are fixed; (3) the values of k_eff are nearly the same if rock blocks are in circular or regular hexagon shapes; and (4) the major axis direction of rock blocks has some influence on k_eff.     

橡胶砂级配对混合土体剪切特性影响研究

为了研究橡胶砂的剪切特性,采用室内大型直剪仪,研究了4种橡胶砂级配（1种间断级配、2种连续级配、1种开级配）、3种橡胶掺入量（10%、30%、60%）、3种竖向应力（30、60、90 kPa）对橡胶砂强度特性和体变特性的影响;并在室内直剪试验的基础上,按照相同级配和橡胶掺量建立纯砂和橡胶砂的离散元数值模型,从颗粒接触状态和颗粒位移角度探讨橡胶砂内在力学机制。研究结果表明：在低橡胶含量下,橡胶砂的剪应力曲线趋势和纯砂一致,但其抗剪强度均低于纯砂;橡胶砂剪切应力随竖向应力的增大而增大,4种级配的橡胶砂中连续级配SR2抗剪强度最高;橡胶颗粒的掺入能有效抑制砂土的剪胀,其中间断级配SR1橡胶砂抑制土体剪胀效果最好,剪胀量相较于纯砂减少了37.6%;橡胶砂的内摩擦角随着橡胶掺入量的增大而减小,同一橡胶掺量下连续级配SR2橡胶砂的内摩擦角最大;橡胶颗粒在橡胶砂力链网络中主要参与弱力链的形成,橡胶砂剪切带宽度小于纯砂的剪切带宽度。     

散粒体斜坡注浆固坡工程防治技术实验研究

目前,国内外对散粒体斜坡的防治措施研究甚少。笔者推荐注浆固坡工程防治技术,具有以动制动特点。本文通过室外注浆物理模拟实验,得出注浆后固结体形态有舌形、灵芝形、柱形、长倒锥形、短倒锥形,其有效半径分别是46.3cm、26cm、21.4cm、16.5cm、40cm、29.4cm。结合现场颗粒取样筛分实验,研究了散粒体堆积结构对注浆固坡措施的影响,提出颗粒间孔隙比的影响最为主要,并通过计算机优化回归得出注浆量及浆液扩散半径的公式;最后对固结体进行直剪试验,得出注浆后的散粒体强度增加,说明了注浆固坡工程的可行性和合理性。这对散粒体斜坡坡体实施注浆加固工程具有重大的参考价值。     

Downstream lightening and upward heavying: Experiments with sediments differing in density

Sorting and selective transport of particles by material density is important for understanding a wide range of processes, including the formation of mineral placers, deposition of mine tailings and routing of tracers and contaminants. This article describes an experimental study of the transport of mixtures of particles of differing density in a sediment‐feed flume. During the runs, a downstream prograding wedge‐shaped deposit was formed. Results show two sorting processes: (i) longitudinal sorting characterized by preferential deposition of heavy particles in the upstream part of the deposit – downstream lightening; and (ii) vertical sorting with less dense particles preferentially deposited in the lowermost portion of the migrating front – upward heavying. Downstream lightening is the analogue of the well‐known downstream fining observed in the more studied case of mixtures of heterogeneous size with the same density. In both cases, the lighter particles are carried further downstream than the heavier particles. Upward heavying is unexpected when compared with deposits of heterogeneous size and same‐density particles, where the heaviest (i.e. coarsest) particles are deposited in the lowermost part of the front. The physical mechanism underlying this upward heavying might be related to the physics of gravity‐driven granular flows; the front of the deposit acts like a dense granular flow down an inclined plane. In this case, the denser particles settle away from the free surface and at the top of the heap, while the lighter particles flow to the bottom. As the front of the deposit advances, this progressively gives rise to an upward heavying pattern. The application of classical surface‐based fractional bedload transport models suggests that equal mobility is not approached in the case of mixtures of particles with uniform size and different densities. This study hypothesizes that other mechanics related to the physics of the segregation processes in these systems contribute to these results.     

A ROLE FOR COVARIANCE STABILIZATION IN THE CONSTRUCTION OF THE CLASSICAL MIXTURE SURFACE

Some well-established ideas from classical covariance stabilization and shrinkage estimation are extendedto the context of physical mixtures through the use of a model developed by Burdick and Rayens.A cross-validation technique is proposed and associated computational issues are addressed.The methodology isevaluated in the context of real polychlorinated biphenyl data.