长江三峡工程对河口近海区理化环境要素的影响

本文在调查研究的基础上,论述了长江径流的主要作用,并且给出了长江径流量分别与含沙量、营养盐含量的经验关系,同时阐述了河口近海区水动力条件,给出了径流量与沿岸锋锋位的回归关系。根据上述关系及长江三峡工程运行预案,研究了工程兴建后可能对河口近海地区理化环境要素分布的影响。研究表明,该工程兴建后虽对河口近海产生一定的影响,但并不会超出历史上自然变化对其影响的范围及程度。     

Results from microseismic monitoring,conventional instrumentation,and tomography surveys in the creation and thinning of a burst-prone sill pillar

Located in northern Québec, the Lac Shortt Mine was a small gold mine consisting of a thin subvertical orebody which was mined in three main phases. High stress and rockbursting conditions were experienced when ore was extracted in the upper zone between the surface and a depth of 500 metres during the first two phases of mining. Severe rockbursts were experienced in late 1989 near the shaft and in the footwall development following a deepening of the mine shaft to a depth of 830 m and partial development of footwall drift access for the third phase of mining (the mining of the lower zone starting at a depth of 830 m moving upward toward a depth of 500 m). A 16-channel Electrolab MP250 microseismic system, with a Queen's University Full-Waveform piggy-back system, was installed underground at the site due to these problems.It was expected that the thinning sill would be subjected to an ever-increasing load as the thickness of the 500 m sill pillar decreased in the face of the mining excavation from below. A monitoring program consisting of the microseismic monitoring system, a range of conventional geomechanics monitoring tools as well as the undertaking of periodic seismic tomography surveys to assess the ongoing state of stress and rock mass condition within the sill was therefore warranted.The anomalously high-magnitude stress field and the brittle rockmass created a situation in which rockmass failure was common and violent. In the creation and thinning of the sill pillar, the location of banded microseismic activity was crucial in tracing rockmass failure and the associated ground control problems. Reliable source-location determination enabled the identification of areas of stress increase. The movement of the rockmass failure front could be followed, and was responsible for stope dilution, footwall and orebody development deterioration, and caving.Source-mechanism analyses gave accurate double-couple solutions for approximately forty percent of these events having at least ten recognizable polarities. Results suggested movement along vertical north-south striking or vertical east-west striking features. Underground observation of damaged access points showed that vertical north-south striking joints were experiencing failure.The microseismic activity, which was consistently concentrated close to the southwest and northeast corners of current production stopes, could be explained by a stress field oriented obliquely to the strike of the orebody, as measured prior to shrinkage of the sill pillar byin situ stress measurements and observed borehole overbreaks. The orientations of theP andT axes for the microseismic activity further confirmed that the stress field oriented obliquely to strike.While an increase in compressional-wave velocity of 2.3 percent, corresponding to a measured stress increase of approximately 10 MPa could be measured by repeated tomographic surveys, it was relatively small and only a factor of two or so above the velocity measured uncertainty. The relative insensitivity of thein situ rock mass modulus to the applied stress is believed to be largely due to the rockmass discontinuities being relatively closed prior to stress increase, as substantiated by the small deformations seen by the extensometer and borehole camera. This situation existed because of the very high pre-mining stress level.The experimental demonstration that the rock could not absorb substantially increased load through the mechanism of discontinuity closure or tightening (which would be reflected in the modulus) may be evidence in itself of potentially burst-prone ground, such as encountered at Lac Shortt.     

大火成岩省及其在古大陆重建及裂解研究中的应用

大火成岩省是地质历史上与地球深部过程（如地幔柱）密切相关的极端地质事件,以相对较短时期内形成规模宏大的板内幔源基性岩浆活动为主要特征,对研究全球性大气—海洋环境的巨变与生物灭绝、大规模成矿及超大陆的重建和裂解均有重要意义。从潘吉亚超大陆的裂解过程可以看出,尽管不是所有的大火成岩省都与大陆裂解有关,但几乎每一次重要的裂解事件都伴有大火成岩省的出现,因此大火成岩省对于研究前潘吉亚超大陆,特别是对于缺少古生物等重建标志,古地磁数据偏少的前寒武纪超大陆重建及裂解研究有重要价值。近20多年来随着年代学技术的进步及研究工作的不断深入,大火成岩省在古大陆重建及裂解方面取得了一些重要进展,并发挥了越来越重要的作用。前寒武纪大火成岩省由于经历了多次裂解事件改造及后期抬升剥蚀或覆盖的影响,现今保留的是一些分散在不同大陆上的大火成岩省残片或碎片。用大火成岩省开展古大陆重建及裂解的目标就是通过不同陆块大火成岩省或大规模基性岩浆活动的年代学、岩石学及地球化学对比,结合其他证据,恢复大火成岩省形成时的时空分布特征,据此来确定这些陆块在超大陆中的相对或绝对位置。与其他前寒武纪大陆重建标志相似,大火成岩省也有一些局限性及不确定性,因此应用大火成岩省开展古大陆重建及裂解研究中要与前岩浆期沉积地层中的特殊事件层（如冰碛岩、火山灰、黑色页岩、不整合面、古生物等）对比、岩墙几何学产状、基性岩浆事件序列对比、古地磁、大型构造（如造山带）对比及深部地球物理等多学科方法相结合。     

Paleoproterozoic gabbronoritic and granitic magmatism in the northern margin of the North China craton: Evidence of crust–mantle interaction

Paleoproterozoic Xuwujia gabbronorites in the northern margin of the North China craton occur as dykes, sills and small plutons intruded into khondalite (aluminous paragneisses, sedimentary protoliths deposited at ca. 2.0–1.95 Ga), and as numerous entrained bodies and fragments of variable scales in the Liangcheng granitoids (ca. 1.93–1.89 Ga). These gabbronoritic dykes are present at all locations where ca. 1.93–1.92 Ga ultra-high-temperature metamorphism is recorded in the khondalite. A gabbronorite sample from the Hongmiaozi dyke gives zircon ²⁰⁷Pb/²⁰⁶Pb mean ages of 1954 ± 6 Ma (core domains) and 1925 ± 8 Ma (rim domains). These ages, as well as previously reported ages, constrain the age of mafic magmatism to be at ca. 1.96–1.92 Ga (∼1.93 Ga). One sample from the Xigou gabbro intruded by the Liangcheng granitoids gives a zircon ²⁰⁷Pb/²⁰⁶Pb mean age of 1857 ± 4 Ma, which is interpreted as the age of a metamorphic overprint. The Xuwujia gabbronorites comprise mainly gabbronorite compositions, as well as some norite, olivine gabbronorite, monzonorite, quartz gabbronorite, and quartz monzonorite. Chemically, they are tholeiitic and can be divided into two groups: a high-Mg group (6.2–22.9 wt.% MgO) and a relatively low-Mg group (2.2–5.7 wt.% MgO). The high-Mg group shows negative Eu-anomalies (Eu/Eu* = 0.53–0.72), slight light rare earth element enrichment (La/Yb_N = 0.56–1.53), and small negative anomalies in high field-strength elements. The ?Nd (t = 1.93 Ga) values vary from +0.3 to +2.4. The low-Mg group shows varied Eu-anomalies (Eu/Eu* = 0.48–1.05), and is enriched in light rare earth elements (La/Yb_N = 1.51–11.98). The majority shows negative anomalies in high field-strength elements (e.g., Th, Nb, Zr, and Ti). Initial ?Nd (at 1.93 Ga) values for low-Mg gabbronorites vary from −5.0 to 0. The Xuwujia gabbronorites possibly experienced assimilation of crust, and fractional crystallization of initially olivine and hypersthene (the high-Mg group), and then olivine, clinopyroxene, and plagioclase (the low-Mg group). The slightly younger Liangcheng granitoids consist of garnet-bearing granite, granodiorite and quartz-rich granitic compositions. They are intermediate to felsic calc-alkaline rocks, thought to be derived from surrounding metasedimentary crust. Xigou gabbro could represent early cumulates. The granitoids have relatively high-Mg numbers (up to 54), and show some chemical affinities with the gabbronorites, which could have resulted from incorporation of gabbronoritic melts. The occurrence and chemical variations of the Xuwujia gabbronorites and Liangcheng granitoids can be interpreted to have resulted from crust–mantle interaction, with mingling and partial mixing of mantle (gabbronoritic) and crustal (granitic) melts. The Xuwujia gabbronorites originated from a mantle region with high potential temperatures (∼1550 °C), possibly associated with a plume or more likely a ridge-subduction-related mantle upwelling event. They could have had extremely high primary intrusion temperatures (up to 1400 °C). Emplacement of these magmas was likely responsible for the extensive crustal anatexis (Liangcheng granitoids) and the local ultra-high-temperature metamorphism. These sequences may have followed ca. 1.95 Ga continent–continent (arc?) juxtaposition and were themselves followed by significant regional uplift and exhumation in the northern margin of the North China craton.     

Occurrence and Dispersal of Magmas in the Jurassic Ferrar Large Igneous Province, Antarctica

Tholeiitic rocks of the Ferrar Large Igneous Province (FLIP) occur in a linear belt from the Theron Mountains to Horn Bluff in the Transantarctic Mountains and extend into southeastern Australasia. The FLIP was emplaced during the initial stages of Gondwana break-up from a source suggested to be in the proto-Weddell Sea region. Magma transport from its source (Weddell triple junction) was controlled by an Early Jurassic zone of extension. The FLIP comprises the Dufek intrusion, Ferrar Dolerite sills and dykes (sheet intrusions), and extrusive rocks consisting of pyroclastic strata overlain by Kirkpatrick Basalt lavas. The Dufek intrusion occurs in deformed supracrustal rocks of the foldbelt along the paleo-Pacific Gondwana margin. A few sills were emplaced in basement rocks, but the majority of the sheet intrusions occur in flat-lying Devonian to Triassic Beacon strata. Only in the central Transantarctic Mountains (CTM) and south and north Victoria Land (SVL, NVL) are extrusive rocks preserved overlying Beacon strata. The greatest cumulative thicknesses of magmatic rocks (ca. 2 km) occur in areas where lavas are preserved (CTM and SVL). Sheet intrusions have complex relationships. Dyke swarms (sensu stricto) are unknown and dykes cutting basement rocks are uncommon. Nevertheless, these dykes, including a 30-m-wide dyke in SVL, suggest that some magmas locally migrated up through basement rocks. In CTM and NVL the outcrop belt has a width of about 160 km. Sills originally extended farther toward the plate margin but have been cut out by erosion and Cenozoic faulting, most clearly in CTM; geophysical data suggest extension under the East Antarctic ice sheet for at least 100 km. Although Early Jurassic extension is documented in CTM, major rift-bounding faults have not been observed. Models for magma emplacement include transport along the axis of the Transantarctic Mountains and off-axis transport from major rift-bounding faults. Contrasts in geochemistry between lavas of NVL (MgO=67%) and CTM (MgO=24%) and the presence of massive dolerite bodies (CTM, SVL) suggest discrete episodes and locations of magma emplacement, and that there was no long range interconnection along the mountain range in supracrustal rocks.     

矿山压力对底板破坏深度监测研究

目前肥城煤田6 1%的煤炭储量受底板奥陶系灰岩岩溶水威胁,采场底板破坏深度的监测是该煤田底板水害防治的重要内容,选择肥城煤田曹庄井田8煤层和9煤层开采作为监测对象,利用向底板岩层注水方法监测岩层破坏情况。利用专利产品“钻孔双端封堵测漏监测仪”,监测煤层采前的底板原始裂隙发育程度和采后矿山压力底板的破坏深度。监测结果表明,8煤层开采造成的底板破坏深度可达36.5m;9煤层开采底板破坏深度可达14.2m。      

Fingered Intrusion of Shallow Saucer-shaped Igneous Sills: Insights from the Jiaojiang Sag, East China Sea

An extensive suite of igneous sills was intruded into the Tertiary sedimentary section of the Jiaojiang sag,East China Sea.This suite has been well imaged offshore through 2D and 3D seismic surveys,showing a close relationship with CO2 content in nearby gas discoveries.A new observational model,which incorporates simple upward propagation,simple horizontal propagation,and transgressive propagation,was proposed to interpret these sill intrusions.In this model,the source magma of the saucer-shaped sills was injected from their lowest points near the center.The transgressive propagation can be interpreted as a combination of the vertical and horizontal propagation.Most shallow sub-volcanic intrusions in the Jiaojiang sag exhibit fingered characteristics,both vertically and horizontally.The vertical fingered propagation produced saucer-shaped sills arranged in the flower style.Along the brims of lower sills could usually be found the upper sills,which are interpreted to have formed simultaneously with or later than the lower feeder sills.In the second type,the chilled paths of the older sills were reutilized by subsequent intrusions.The horizontal fingered propagation formed sheet intrusions that exhibit groove,lobate,tubular,and crevasse splaylike geometry in plan view.In 3D view,the sheet intrusions have still preserved the lower center and higher rim that similar with the sub-rounded saucer-shaped sills.Although fracture propagation may be important,flow inflation was the key mechanism of magma intrusion.Further consideration of the mechanisms underlying sill formation may help explain the fingered characteristics of sill propagation.