盾构隧道下穿管道施工引起的管-土相互作用研究

采用Loganathan公式研究了盾构隧道下穿管道施工引起的地下管道处土体竖向位移,利用考虑土中剪力传递的Pasternak模型模拟管-土相互作用,运用修正Vlasov模型中的迭代流程计算出Pasternak模型的关键参数——弹性系数k与剪切系数gs。将计算结果与已有文献结果及工程监测数据进行对比,深入分析了迭代求解k、gs值的Pasternak模型与传统模型的计算差异,并进一步研究了土中剪力、管道与隧道的夹角、土体弹性模量及隧道半径的变化对管-土相互作用的影响。研究结果表明：迭代求解的k、gs值能提升Pasternak模型的精确度;土中剪力对管道竖向位移计算值的影响可达15.3%;随着管道与隧道夹角的减小,管道的竖向位移增大、弯矩减小;土体弹性模量与隧道半径的增大均会增加管道的竖向位移和弯矩。     

由环境应力值寻找地震危险区的尝试

作者根据位错理论,采用二维矩形破裂模式,在导出了平均震源速度谱的基础上,导出了用地震波计算环境剪应力τ_0的公式。计算了1987—1991年中国和邻区大约1000多次4级以上中强地震的环境剪应力值τ_0,并把τ_0≥10MPa的地震看作是高剪应力值地震。自1987—1991年5年内,我国及邻区共发生M_s≥6.0的强震45次,和160余次高剪应力中强地震(M=4.0-5.0,τ_0≥10MPa),大约有1/4的强震和1/3的高应力值地震发生在台湾地区。说明台湾地区是一个高地震活动区和高应力值地区。新疆的喀什—乌恰—乌什地区也是高地震活动区和高应力值地区。我们对发生在其地区的强震,向前追溯了环境应力值τ_0的变化。发现有11个强震事件(约占全部事件80%)在震前1—5年内,在以强震为圆心,半径为200km范围内(个别略远),均有1—2个或多个高应力值地震出现。说明当高应力值地震发生时,该地区环境应力在增高,它可以作为将要发生强震的前兆。据此,推测了今后3年内大陆强震发生的可能地区是:①中印缅三国边境地区;②西藏波密地区;③青海北部到宁夏北部地区;④新疆伊宁地区;⑤纵贯新青藏90°E±2°线地带;⑥晋北忻州地区;⑦苏北及黄海地区;⑧山东长岛地区。     

循环荷载下砂土的剪切硬化边界面本构模型

基于临界状态土力学框架,建立了一个适用于往返循环荷载作用的砂土边界面本构模型。采用无纯弹性域假设,认为受到反向荷载的瞬时土体就产生塑性变形,砂土的弹性区域退化为一个点。屈服面为倒子弹头型,由于砂土孔隙比与压力之间不存在惟一对应的关系,使得屈服面大小无法与体积应变直接耦合,故采用塑性偏应变而不是剑桥模型那种塑性体应变作为硬化参数。流动法则采用加入状态参数的修正的Rowe应力剪胀关系,体现了依赖状态的剪胀思想。屈服面大小的比值 反映了塑性模量的演化,并推导了 的表达式。只用1套参数,该模型就能合理地模拟砂土在不同密度和固结压力下循环荷载的应力-应变关系曲线。     

低地应力区地下洞室开挖围岩剪应力静态数值模拟研究

本文以西北某市大型水利地下洞室工程为例,采用弹塑性二维有限元法对低地应力区洞室开挖后围岩剪应力分布与围岩变形破坏进行了数值模拟,总结出了低地应力区地下洞室开挖后围岩剪应力大小、分布规律与围岩变形破坏的关系.该项研究它将有利于进一步研究低地应力区地下洞室开挖后围岩稳定性,同时对保障地下洞室工程的圆满进行具有重要的理论价值和现实意义.     

岩石空心圆柱扭剪仪研制的重点问题及研究进展

随着深部岩体工程的发展,开挖卸荷导致的应力主轴旋转问题引起了广泛关注。首先,分析总结了岩体工程中存在的应力主轴旋转问题及其对岩体工程稳定性的影响;其次,介绍了土体空心圆柱扭剪仪的发展现状及其特点,从荷载的施加方式、试样尺寸两个方面指出了研制岩石空心圆柱扭剪仪的关键问题,并与土体空心圆柱扭剪仪进行了对比,提出了新的扭矩施加技术和合理的岩石空心圆柱试样尺寸;最后,总结概括了考虑应力主轴旋转的土体本构模型的研究成果,并对考虑应力主轴旋转的岩石本构关系的研究进行了展望。该工作将对岩石空心圆柱扭剪仪的研制和相关理论的研究提供一定的参考和指导。     

Laboratory modelling of shear behaviour of soft joints under constant normal stiffness conditions

Shear behaviour of regular sawtooth rock joints produced from casting plaster are investigated under constant normal stiffness (CNS) conditions. Test results obtained in this investigation are also compared with the constant normal load (CNL) tests. It is observed that the peak shear stress obtained under CNL conditions always underestimates the peak shear stress corresponding to the CNS condition. Plots of shear stress against normal stress show that a nonlinear (curved) strength envelope is acceptable for soft rock joints subjected to a CNS condition, in comparison with the linear or bilinear envelopes often proposed for a CNL condition. Models proposed by Patton (1966) and Barton (1973) have also been considered for the predictions of peak shear stress of soft joints under CNS conditions. Although Patton's model is appropriate for low asperity angles, it overestimates the shear strength in the low to medium normal stress range at higher asperity angles. In contrast, while Barton's model is realistic for the CNL condition, it seems to be inappropriate for modelling the shear behaviour of soft joints under CNS conditions. The effect of infill material on the shear behaviour of the model joints is also investigated, and it is found that a small thickness of bentonite infill reduces the peak stress significantly. The peak shear stress almost approached that of the shear strength of infill when the infill thickness to asperity height ratio (t/a) reached 1.40. This paper also introduces an original, empirical shear strength envelope to account for the change in normal stress and surface degradation during CNS shearing. © Rapid Science Ltd. 1998     

A traversing system to measure bottom boundary layer hydraulic properties

This study describes a new convenient and robust system developed to measure benthic boundary layer properties, with emphasis placed on the determination of bed shear stress and roughness height distribution within estuarine systems by using velocity measurements. This system consisted of a remotely operated motorised traverser that allowed a single ADV to collect data between 0 and 1 m above the bed. As a case study, we applied the proposed traversing system to investigate bottom boundary layer (BBL) hydraulic properties within Coombabah Creek, Queensland, Australia. Four commonly-employed techniques: (1) Log-Profile (LP); (2) Reynolds stress (RS); (3) Turbulent Kinetic Energy (TKE); and (4) Inertial Dissipation (ID) used to estimate bed shear stresses from velocity measurements were compared. Bed shear stresses estimated with these four methods agreed reasonably well; of these, the LP method was found to be most useful and reliable. Additionally, the LP method permits the calculation of roughness height, which the other three methods do not. An average value of bed shear stress of 0.46 N/m², roughness height of 4.3 mm, and drag coefficient of 0.0054 were observed within Coombabah Creek. Results are consistent with that reported for several other silty bed estuaries.     

北京721特大暴雨极端性分析及思考（二）极端性降水成因初探及思考

本文是“北京7.21特大暴雨极端性分析及思考”的第二部分,第一部分“观测分析及思考”对此次过程的降水特点、水汽特点、中尺度对流系统（MCS）的环境场条件和发生发展过程进行了分析,指出这是一次极端降水过程。本文进一步从影响降水的因子：降水效率、水汽、上升运动、持续时间等方面进一步探讨极端性降水的成因,所用资料为业务中常用的模式分析和各种观测资料。分析表明,本次过程为典型华北暴雨环流形势,其中高层气流辐散区与低层低涡切变线的耦合是直接诱因;较高的环境相对湿度和湿层较厚,较低的抬升凝结高度和自由对流高度以及热带降水性质提高了本次过程的降水效率;异常大的水汽含量（可降水量达60－80mm）及与其相关的物理量异常,可作为判断极端降水的重要因子;环境大气具有中下层条件性不稳定,上层湿中性层结特性,CAPE值中等,同时上层干侵入增加了对流不稳定,有利于上升运动发展;低涡切变线及华北地形共同触发了MCS的在暖区生成发展;低涡北跳、MCS后向传播特性使暖区MCS东移速度慢,形成“列车效应”,造成降雨持续时间长。本文最后探讨了极端降水的预报思路。     

灞源韧性剪切带特征及其地质意义

本文对灞源地区不同时代的韧性剪切带的运动学、动力学特征进行了研究。笔者认为,前人所称的部分太华群(Arth_3b)是太古宙末期太华群韧性变形的产物;张家坪花岗岩以左旋螺旋式上升侵位;燕山期,多期活动韧性剪切带是本区金矿形成富集的主要原因之一。     

裂隙面对强膨胀土抗剪强度影响分析

膨胀土作为一种特殊性土,其抗剪强度取值不同于一般的黏性土。实践证明,在进行膨胀土边坡设计时,不仅要考虑土体的土块强度,而且也要考虑裂隙面强度,其抗剪强度在很大程度上受其裂隙面规模与产状的影响,尤其是对裂隙极发育的强膨胀土而言。为了更加真实地模拟强膨胀土在裂隙面控制下的剪切破坏,特在南水北调中线工程南阳段强膨胀土地段进行大剪试验,通过拟合试验数据,对强膨胀土抗剪强度影响因素进行分析。结果表明,裂隙面的发育程度、倾角、裂面的起伏程度都对强膨胀土的抗剪强度有着很大的影响。