南沙海域万安盆地地质构造特征

利用在南沙海域万安盆地所采集的地震、重磁资料及钻井、地质资料，对该盆地的地震反向特征，沉积特征、区域地质、构造特征及构造发展史进行了的简要的论述，本文以该区Ｔｇ深度资料为基础，并利用ＣＣＯＰ年刊发表的新生代基底深度资料，初步圈定了万安盆地的边界，并对盆地二级构造单元进行了划分，将盆地划分为５坳３隆、坳隆相间的构造格局。     

具有内波特性的渤海南部次重力波

次重力波(infragravity waves)是频率范围介于局地平均Brunt-V¾is¾l¾频率和0.05Hz(涌浪频率)之间的一种海洋波动,其能量在深水大洋中一般甚低,但在浅海中却很强.该波动的研究对于浅海海洋内部混合、近岸海洋工程、海洋生态学、海洋沉积学及军事海洋学均有重要的意义.Munk[1]很早就开始研究这类波动,然而主要由于观测技术的限制,对于该类波动的动力学机制的研究进展迟缓.     

黄河口快速沉积及其动力过程

现场观测资料和卫星遥感校准图像计算表明 ,185 5年以来 ,黄河三角洲新淤陆地 36 99km2 ,生长速率为 2 6 8km2 /a ,黄河输入三角洲 1× 10 8t泥沙形成 3 14 4km2 的陆地。进入河口区的泥沙约 88 4 %堆积在水下 8km宽的三角洲前缘。研究表明 ,这一堆积比例是河口切变锋、异重流和潮流场相互作用的结果 ,异重流在黄河汛期一直存在 ,大约搬运黄河来沙的 6 0 %沉积在三角洲前缘 ;一个潮周期内 ,切变锋出现两次 ,它能够捕获异轻羽状流中的悬浮泥沙堆积 ,也能够限制异重流的远距离扩散。切变锋消失后 ,少量悬浮泥沙才能远距离扩散 ,随潮流离开三角洲水下斜坡。     

基于新型高频声学多普勒流速剖面仪的河口近底部边界层观测初探

河口物质输运、能量交换与底边界层内的水动力过程密切相关,底边界层参数(如切应力、拖曳系数)的确定至关重要。挪威Nortek公司生产的新型声学多普勒流速剖面仪AD2CP相比传统ADCP具有高频、低噪的优点,可用于高频(16Hz)流速剖面观测,而被广泛应用于底边界层观测的ADV只能测量单点高频流速。本文采用AD2CP在长江口南槽最大浑浊带区域进行座底式观测,并与同步近底部三脚架上ADV的观测结果进行对比。结果表明,使用AD2CP测得的近底部平均流速与ADV的测量结果吻合良好;使用惯性耗散法计算了底切应力,基于ADV的单点高频流速数据计算结果为2.16×10~(-2)～5.69×10~(-1)N/m~2,基于AD2CP的结果为2.09×10~(-2)～4.26×10~(-1)N/m~2,二者范围大致相当。在此基础上,基于AD2CP数据计算出摩阻流速为4.55×10~(-3)～2.06×10~(-2)m/s、底拖曳系数范围为1.84×10~(-4)～2.49×10~(-3),与ADV的计算结果基本一致。此外,由于AD2CP可以获得高频的流速剖面数据,优于单点ADV,具备观测近底部边界层参数和边界层内湍流剖面的潜力。     

Effect of sand on the vacuum consolidation of dredged slurry

Vacuum preloading is often used to improve the geotechnical properties of dredged slurry. Although the performance of this method has improved with rapidly developing technology, soil columns usually formed on the drainage boundary induce the decrease of permeability around the boundary, thereby limiting the further development of this method. To address this issue, this paper proposes a method for pretreating the slurry combined with sand prior to vacuum consolidation. This method partially replaces the fine particles with sand to reduce the formation of soil columns. Two groups of vacuum preloading tests were performed to investigate the effect of sand content and sand grain size on the vacuum consolidation of dredged slurry. The test results revealed that for a given sand grain size, increasing the sand content of the sand–slurry mixture increased the pore water drainage and accelerated the dissipation of pore water pressure, thereby increasing the vane shear strength. In contrast, for a constant sand content, the samples containing coarse sand exhibited increased pore water drainage and accelerated dissipation of pore water pressure, thereby increasing the vane shear strength of the soil.     

胶南地区的伸展作用——以胶南—诸城一带为例

胶南地区的胶南—诸城一带存在两期不同方向的伸展构造。早期以形成近ＥＮ向的拉伸线理为特征，并在不同构造层次上显示出不同的变形。出露于研究区中部桃林尚庄隆起的含榴辉岩片麻岩中，主要以ＬＳ的组构为特征，显示出早期伸展作用下地壳岩石的垂直轴缩短、ＥＷ向拉伸的共轴应变；而在把下地壳含榴辉岩片麻岩与以变沉积岩为主的中上地壳岩石分开的韧性滑脱带上，此期伸展作用则表现为从东向西剪切的非共轴简单剪切变形，具有近水平的拉伸线理及近水平的ＥＷ向剪切褶皱和鞘褶皱枢纽。晚期伸展作用表现为近ＳＮ的伸展垮塌作用，形成向北和向南倾斜的两条韧性正剪切带，且遭受低角闪岩高绿片岩相条件下的透入性均匀简单剪切变形，剪切方向分别向北和向南。     

晋北娄烦吕梁群变质相带的划分及其成因研究

晋北娄烦吕梁群由一套经受过两期不同性质变质作用的泥砂质岩、基性火山岩和酸性流纹岩组成。早期为吕梁期变质作用,其结果使该区地层构造形迹总体上呈NE走向;晚期为西川河韧性剪切断裂所产生的区域变质作用,其结果使该区地层走向由早期的NE向扭转为近SN向,且使地层层序发生倒转,并与递增变质带的形成关系密切。选取该区中对变质温度和压力变化反映较敏感的原岩为泥砂质岩石的袁家村组和裴家庄组地层为研究对象,采用电子探针微区分析(EPMA)对沿地层走向上连续分布的特征变质矿物及矿物共生组合特征进行研究,并利用矿物对地质温度计估算该区不同采样点的变质温度和压力条件,对研究区进行变质相带的划分,确定各变质相带的变质温、压条件,并探讨其成因。研究结果表明,袁家村组和裴家庄组为等化学系列地层。沿该地层走向上:西川河断裂以北地区,从北向南,特征变质矿物绿泥石、黑云母、石榴石、十字石和蓝晶石依次规律出现;西川河断裂以南地区,红柱石和夕线石依次规律出现。根据特征变质矿物的空间分布规律、首次出现的地点及矿物共生组合特征,划分出5个变质带:绿泥石带、黑云母带、石榴石带、十字石-蓝晶石带和红柱石-夕线石带。这一完整的递增变质带可与苏格兰高地的巴罗型相媲美。矿物对地质温度计估算结果。     

基于剪切波速的深层砂土地震液化研究

阐述了剪切波速法判别饱和砂土液化的原理,结合武汉地区某工程实例,对场地内埋深超越"规范法"适用范围的砂层进行液化判别,确定场地的临界液化深度。通过与室内动三轴试验的对比得出,2种方法的液化判别结果及确定的临界液化深度均吻合较好,验证了以剪切波速为指标的液化评估方法的可行性。     

A traversing system to measure bottom boundary layer hydraulic properties

This study describes a new convenient and robust system developed to measure benthic boundary layer properties, with emphasis placed on the determination of bed shear stress and roughness height distribution within estuarine systems by using velocity measurements. This system consisted of a remotely operated motorised traverser that allowed a single ADV to collect data between 0 and 1 m above the bed. As a case study, we applied the proposed traversing system to investigate bottom boundary layer (BBL) hydraulic properties within Coombabah Creek, Queensland, Australia. Four commonly-employed techniques: (1) Log-Profile (LP); (2) Reynolds stress (RS); (3) Turbulent Kinetic Energy (TKE); and (4) Inertial Dissipation (ID) used to estimate bed shear stresses from velocity measurements were compared. Bed shear stresses estimated with these four methods agreed reasonably well; of these, the LP method was found to be most useful and reliable. Additionally, the LP method permits the calculation of roughness height, which the other three methods do not. An average value of bed shear stress of 0.46 N/m², roughness height of 4.3 mm, and drag coefficient of 0.0054 were observed within Coombabah Creek. Results are consistent with that reported for several other silty bed estuaries.