Land subsidence caused by compression of clay layers in Ojiya City, Japan was measured by global positioning system (GPS) between 1 April 1996 and 31 December 1998.
Three baselines were selected in and around the city, and height difference on a WGS-84 ellipsoid was measured by GPS on each baseline. The ground at the GPS station in the city subsides and rebounds 7 cm every winter and spring, respectively. Measurement accuracy was 9.5 mm standard deviation. Ground water level was observed at a well near the GPS station. Regression analysis between total strain, calculated as ratio of the height difference displacement to the total thickness of the clay layers, and the layers' effective stress change with ground water level change gave good correlation. The slope of regression line 7.0×10−11 m2/N was obtained as an average apparent coefficient of volume compressibility of the layers. 相似文献
This contribution explores a strategy for landslide hazard zonation inwhich layers of spatial data are used to represent typical settings inwhich given dynamic types of landslides are likely to occur. Theconcepts of assessment and prediction are defined to focus on therepresentation of future hazardous events and in particular on themyths that often provide obstacles in the application of quantitativemethods. The prediction rate curves for different applications describethe support provided by the different data layers in experiments inwhich the typical setting of hazardous events is approximated bystatistically integrating the spatial information. 相似文献
Rockfall susceptibility has been analysed in mountain cliffs of the Cantabrian Range, North Spain. The main aim of this analysis has been to build a predictive model of rockfall activity from a low number of environmental and geological variables. The rockfall activity has been quantified in a GIS. The cartographic information used shows the spatial distribution of all the recent talus screes as well as their associated source areas in the rock-slopes. The area relation At/Ar (recent talus scree polygon/source basins) in the rock slopes has been used as the rockfall activity indicator. This relation has been validated in 50 pilot rock-slopes and compared with the relation number of recent rock fragments/source basin, obtained from field work. The environmental factors causing rockfall depend on the rock slope situation, and these are: altitude and sun radiation on the rock cliff. The geological factors considered are: lithology, relative position of the main discontinuities with respect to the topographic surface and two morphologic parameters: the roughness and slope gradient. A logistic regression analysis has been applied to a population of 442 limestone and quartzite rock cliffs. The dependent variable is the rockfall activity indicator, which allows the definition of two classes of rock cliff units: low and high activity. The independent variables are altitude, sun radiation (equinox radiation, summer solstice radiation, winter solstice radiation), slope roughness, slope gradient,anisotropy and lithology. Results suggest that it is possible tobuild a valid cartographic predictive model for rockfall activity in mountain rock cliffs from a limited number of easily obtainable variables. The method is especially applicable in massive rock slopes or in regions with uniform rock mass characteristics. 相似文献
Abstract The Joggins Formation was deposited in the Cumberland Basin, which experienced rapid mid‐Carboniferous subsidence on bounding faults. A 600 m measured section of coastal and alluvial plain strata comprises cycles tens to hundreds of metres thick. The cycles commence with coal and fossiliferous limestone/siltstone intervals, interpreted as widespread flooding events. These intervals are overlain by coarsening‐upward successions capped by planar‐based sandstone mounds, up to 100 m in width that represent the progradation of small, river‐generated delta lobes into a standing body of open water developed during transgression. The overlying strata contain sand‐rich heterolithic packages, 1–8 m thick, that are associated with channel bodies 2–3 m thick and 10–50 m wide. Drifted plant debris, Calamites groves and erect lycopsid trees are preserved within these predominantly green‐grey heterolithic sediments, which were deposited on a coastal wetland or deltaic plain traversed by channel systems. The cycles conclude with red siltstones, containing calcareous nodules, that are interbedded with thin sandstones and associated with both single‐storey channel bodies (1–1·5 m thick and 2–3 m wide) and larger, multistorey channels (3–6 m thick) with incised margins. Numerous channel bodies at the same level suggest that multiple‐channel, anastomosed river systems were developed on a well‐drained floodplain. Many minor flooding surfaces divide the strata into parasequences with dominantly progradational and aggradational stacking patterns. Multistorey channel bodies are relatively thin, fine grained and modestly incised, and palaeosols are immature and cumulative. The abundance and prominence of flooding surfaces suggests that base‐level rise was enhanced, whereas the lack of evidence for abrupt basinward stepping of facies belts, coupled with the absence of strong fluvial incision and mature palaeosols, suggests that base‐level fall was suppressed. These architectural features are considered to reflect a tectonic architectural signature, in accordance with the high‐subsidence basinal setting. Evidence for restricted marine influence and variation in floral assemblages suggests modulation by eustatic and climatic effects, although their relative importance is uncertain. 相似文献
The inference of fault geometry from suprajacent fold shape relies on consistent and verified forward models of fault-cored folds, e.g. suites of models with differing fault boundary conditions demonstrate the range of possible folding. Results of kinematic (fault-parallel flow) and mechanical (boundary element method) models are compared to ascertain differences in the way the two methods simulate flexure associated with slip along flat-ramp-flat geometry. These differences are assessed by systematically altering fault parameters in each model and observing subsequent changes in the suprajacent fold shapes. Differences between the kinematic and mechanical fault-fold relationships highlight the differences between the methods. Additionally, a laboratory fold is simulated to determine which method might best predict fault parameters from fold shape. Although kinematic folds do not fully capture the three-dimensional nature of geologic folds, mechanical models have non-unique fold-fault relationships. Predicting fault geometry from fold shape is best accomplished by a combination of the two methods. 相似文献