密肋壁板结构计算模型及Pushover分析

在前期试验和理论研究的基础上,将密肋壁板结构中的密肋复合墙板等效为整体斜撑,提出结构的刚架 - 等效斜撑力学模型,并结合试验数据确立了该模型主要参数的计算方法及塑性铰的设定.采用该模型对一实际密肋壁板结构进行了Pushover分析并进行了抗震性能评估.结果表明采用该模型是实现密肋壁板结构Pushover分析及抗震性能评估的一种有效方法.     

Theoretical investigation of large-amplitude waves in granular soils

A theoretical investigation of plane waves in granular soils is presented. Dynamic equations are derived with the use of the hypoplasticity theory for granular materials. For numerical calculations the material parameters of Karlsruhe sand are used. Wave speeds as slopes of characteristics of the dynamic equations are calculated for various stresses and densities. It is shown that under certain conditions the dynamic equations lose hyperbolicity and the initial boundary value problem thus becomes ill-posed. Two types of ill-posedness are found, known as flutter ill-posedness and stationary discontinuity. The latter is shown to arise at higher shear stress than the former. A comparison is made between dynamic ill-posedness and stability of static equilibrium. With the use of the second-order work stability criterion it is found that the dynamic equations lose hyperbolicity when the static equilibrium under a dead load is still stable. Numerical solutions to the problem of propagation of boundary disturbance in a half-space are obtained. Owing to dilatancy and contractancy of the granular material, a purely transverse disturbance induces a longitudinal component of velocity in the wave, and vice versa.     

基于岩体塑性位错理论的龙门山区域构造系统演化过程

青藏高原对四川盆地的挤压作用导致了龙门山断裂带的形成及其山脉的隆起。本文以龙门山附近区域板块运动以及深部岩体力学特性为背景,采用FLAC3D软件模拟再现了时间跨度为700万年的龙门山区域构造系统演化过程。研究结果表明:在板块运动作用下,F1、F2和F3断层依次形成,贯通的断层对地表的抬升具有较强的控制作用,当断层贯通于地表后,龙门山及其以西的川西高原持续隆起,平均抬升速率约为1.38mm/yr,而龙门山断裂带以东的川西坳陷只有较小的抬升量,从而导致川西高原抬升8996 m,致使该区域产生6000m左右的落差,模拟的地形特征与目前的龙门山地形地貌基本相似。依据模拟结果与实测资料,绘制了龙门山断裂带形成及其附近区域地形地貌的演化过程图,呈现了板块挤压、断层塑性位错、地表侵蚀和沉积作用等因素共同作用对地形地貌的塑造过程。     

基于Hoek-Brown准则的隧洞围岩变形研究

由于在许多实际条件下,比如节理岩体中,线性的M-C准则不太适用,非线性的Hoek-Brown比较适用,因此,可以尝试使用这一非线性屈服准则对洞室变形进行研究。研究隧洞变形时,将围岩分为弹性区、应变软化区、塑性流动区。采用Hoek-Brown准则和非关联流动法则对洞室变形进行了理论推导;软化区域围岩参数随着塑性变形增加而变化,解析法难以求得应力,采用龙格－库塔方法进行数值计算,求解得到塑性软化区和流动区半径,并最终求得洞室变形。通过算例计算表明,在不考虑软化区和流动区时,方法和Carranza-Torres计算结果相差甚小;随着原岩应力的增加,膨胀角对洞室变形的影响增大。     

基于Ls-Dyna的高能射流式冲击器活塞杆回程应力分析

针对在钻探实践中高能射流式冲击器的活塞杆频繁出现尾部塑性变形严重影响冲击器工作性能和整体寿命的现象,拟对活塞杆进行优化改进。利用非线性动力学仿真软件Ls-Dyna对活塞杆的回程撞击缸体进行数值模拟和优化分析,并进行了室内试验,结果表明：冲击末速度为4 m/s,活塞杆回程撞击缸体强制停止运动瞬间,尾部产生的应力集中值为3 339.28 MPa,导致其破坏;优化改进后,活塞杆上下端直径比为17/16、尾部圆弧直径为60 mm,活塞杆体内的应力集中值为1 419.66 MPa,较改进前活塞杆的应力集中值减小58%。试验验证表明,优化后的活塞能大幅提高使用寿命和耐久性。     

黏土中两种不同直径单桩水平循环加载模型试验与分析

为探讨海上风机在风、浪等水平往复循环荷载下大直径单桩基础的循环弱化特性,设计了稳定输出长期循环荷载的机械加载装置,开展了软黏土中长期水平循环荷载下海上风电大直径单桩基础和传统长桩基础的模型试验对比研究。根据API给出的骨干曲线和Masing二倍准则构建循环荷载下的p-y（荷载-位移）曲线,并借鉴前人工作,采用累积塑性应变描述软黏土的不排水抗剪强度弱化,提出了分析大周数水平循环荷载下单桩基础循环弱化的理论方法。该方法将循环荷载次数、幅值等外界条件与桩周土体的循环弱化特性建立联系,以适应海洋环境复杂多变的水平循环荷载形式。通过模型试验和理论研究认为,大直径单桩基础因刚度较大,在同样的水平力循环荷载条件下,其抵抗循环荷载的能力明显优于传统长桩。在海上风机大直径单桩的设计中采用基于黏土残余强度的循环后稳定水平承载力更为合理。     

Experimental evaluation of shear strength behaviour of plastic and non-plastic silts

Silt is available in many parts of the world in combination with sands and clays. However, due to lack of clear understanding of its engineering behaviour, most of the time it is interpreted in terms of either sands or clays. Structures that are usually built on silty soils are designed to take into account design procedures developed for sandy or clayey soils. Presence of silts in combination with varying amount of sand and clays produces silt that is either plastic or non-plastic in nature. Silt is available in and around the Delhi region, in a majority mixture along with fine sands, which is non-plastic in nature. On the other hand silty deposits found in offshore Bombay High region are found in abundance along with significant amounts of clays and are termed as plastic silts. In this paper a comparison of the stress-strain behaviour of plastic and non-plastic silts is carried out under triaxial compression loading during both drained and undrained conditions. Two representative samples each from Delhi and Bombay High regions were considered for this comparison and results of stress-strain under four sets of confining pressure are discussed in detail. It is observed from this study that behaviour of silts is mainly dependent on the composition and structure of the resultant soil matrix. It is concluded from the results that shear strength parameters as well as volume change/pore pressure response of silty soils is dominated by the constituent soil present along with the silt. It is seen from the comparative behaviour of non-plastic and plastic silts that the presence of sand and clays has a governing effect on pore pressure development and the resultant friction angle. The study also corroborated that the nature of silt is transitional both in the case of plastic and non-plastic forms.     

塔里木盆地北缘兴地断裂构造变形特征

兴地断裂发生在中元古代末期，使中元古巨厚的沉积岩发生了强烈褶皱和隆起，并伴有大量岩浆侵入和区域变质作用。在兴地断裂形成的同时，发生了第一期构造变形，其特点以韧性变形为主，由三个变形幕构成，形成了本区主要构造骨架；晚元古代本区进入晋宁期发展阶段，团结的塔里木地台基底局部裂开，形成一系列近东西向的断陷盆地，发生了第二期变形，形成以塑性变形为主的板劈理和千枚理为其特征。该期变形结束了塔里木基底发展，进入了稳定盖层沉积发展阶段；进入早古生代，兴地断裂控制了该时期的沉积作用，之后发生第三期变形，以脆性变形为主，形成一系列碎裂岩和脆性变形组构，使兴地断裂形成几十米乃至上百米宽的破碎带，从而改造了早期的糜棱岩；至中、新生代，兴地断裂再次活动，形成断裂两侧南升北降的扭动形迹。通过对兴地断裂的深入探讨，笔者认为：该断裂具有线性特征明显，活动时间漫长，构造变形复杂，是塔里木盆地北缘规模巨大的复活大断裂。     

比奥固结理论在堆载预压加固工程场地中运用

运用平面应变比奥固结有限单元法，对南京某钢铁厂江边原料厂采用堆载预压结合塑料排水板处理的软土地基进行了计算，得到了较为理想的效果。计算中将塑料排水板合理地简化成等效砂墙，理论计算结果与实测结果吻合较好。验证了计算方法是合理可行的。     

Energy demands for seismic design against low‐cycle fatigue

A seismic design procedure that does not take into account the maximum and cumulative plastic deformation demands that a structure is likely to undergo during severe ground motion could lead to unsatisfactory performance. In spite of this, current design procedures do not take into account explicitly the effect of low‐cycle fatigue. Based on the high correlation that exists between the strength reduction factor and the energy demand in earthquake‐resistant structures, simple procedures can be formulated to estimate the cumulative plastic deformation demands for design purposes. Several issues should be addressed during the use of plastic energy within a practical performance‐based seismic design methodology. Copyright © 2006 John Wiley & Sons, Ltd.