An experimental study on seismic responses of multifunctional vibration‐absorption reinforced concrete megaframe structures

Two models are tested on a shake‐table. One of the models is a normal reinforced concrete megaframe structure and the other is a multifunctional vibration‐absorption reinforced concrete megaframe structure in which the laminated rubber bearings are placed between the major frame and the minor frames. Two earthquake motions (the El Centro wave and the Taft wave) are used during the test. This paper presents the dynamic characteristic, the seismic responses and the failure mechanism of these two models under varying peak acceleration levels for each of the earthquake motions. The test results demonstrate that the aseismic behavior of a multifunctional vibration‐absorption reinforced concrete megaframe structure is much better than that of a normal reinforced concrete megaframe structure. Copyright © 2003 John Wiley & Sons, Ltd.     

Seismic structural control using an electric servomotor active mass driver system

This study investigates an electric‐type active mass driver (AMD) system for structural vibration control. Composed primarily of an electric servomotor and a ball screw, the electrical AMD system is free from noise problems, oil leakage, and labor‐intensive maintenance that commonly are associated with hydraulic AMD systems. The desired stroke amplification of the mass and the power demand of the servomotor can be adjusted via the ball screw pitch, which in turn affects the effectiveness and efficiency of the system. Meanwhile, an instantaneous optimal direct output feedback control algorithm is adopted. Numerical simulation is performed using a five‐story steel frame as the object structure under the conditions of the 1940 El Centro earthquake. The AMD system proves to be effective and efficient within a certain range of the ball screw pitch. The reductions of the peak responses can reach as high as 70% if properly designed. Requiring only the velocity measurement of the top floor for on‐line feedback control, the proposed control algorithm is recommended for practical implementation. Copyright © 2004 John Wiley & Sons, Ltd.     

Fundamental study on the response characteristics of drivers during an earthquake based on driving simulator experiments

After the 1995 Kobe earthquake, the expressway structures in Japan were retrofitted and they will not now be seriously damaged under a certain level of strong earthquake motion. However, the stability of a moving vehicle has not been investigated yet. It has been reported that drivers feel seismically induced vibrations, especially in the transverse direction of vehicles. Owing to this phenomenon, drivers have some difficulty in controlling the vehicles during strong shaking. For further safety promotion of the expressway networks, it is important to understand the drivers' reactions to seismic motion. The present authors have performed a series of seismic response analyses of a moving vehicle to investigate its response characteristics based on numerical simulation. However, the responses of the driver were not considered in the simulation process. In order to investigate the drivers' reactions during an earthquake, a series of virtual tests were conducted using a driving simulator. This driving simulator has six servomotor‐powered electric actuators that control its motions. Several types of tests were carried out for different examinees to investigate drivers' responses while controlling the simulator under seismic motion. The results of this study showed that a larger response time lag to strong shaking and over turning of the steering wheel may shift the vehicle into the next lane. According to this finding, trafficaccidents could possibly occur under strong ground shaking in the case of heavy traffic. Copyright © 2004 John Wiley & Sons, Ltd.     

Study on Ground Motion Attenuation Relation in Shanghai and Its Adjacent Region

Based on intensity data in Shanghai and its adjacent region, the intensity attenuation relation is determined. Selecting the western United States as a reference area where there are rich strong ground motion records and intensity data, and by determining ground motion attenuation relation in an area lacking in strong ground motion data, we obtain the ground motion attenuation relation in Shanghai and its adjacent region.     

傅立叶相位分析导风技术的适用范围和相位重叠分析

本文利用傅立叶相位分析法对示踪云进行频域波谱分析，通过谐波的相位变化计算波速，从而导出云迹风(Cloud Motion Wind—CMW)。本文研究表明，对于给定的导风云图序列，如果示踪云在给定时间间隔内的位移小于两个像距，适用傅立叶相位分析法计算云迹风；否则，在用傅立叶相位分析法计算波速时由于高次谐波出现相位重叠，从而使计算的波速小于实际风速，此时适用最大相关系数法。     

水流冲击管道内滞留气团的刚性数学模型

通过数学分析证明,在不计局部水头损失时,目前常用的几种简化刚性数学模型的最大气压计算结果相等,并与管道内初始充水段长度无关。但算例表明,对于初始充水段较短或滞留气团体积很小情况,这些简化模型的计算误差将达到不容忽视的程度,甚至导出错误结论。笔者导出的完整刚性数学模型,弥补了简化模型的不足,同时指出了刚性模型的理论缺陷和适用条件。     

澜沧江某水电站左岸地下式厂房岩体质量分级

通过大量的现场调查数据与统计工作结果，采用了多种岩体质量分级评价方案，对澜沧江某水电站左岸地下式厂房岩体质量进行了精细的评价，最后将各种结果进行对比分析，得到一个合理、科学的综合岩体质量综合评价分级。并根据评价结果，作出了研究区坝址左岸地下式厂房岩体在不同高程的岩体质量分区图，为下一步的参数选取工作奠定了必要的基础。     

Geological controls on rock mass classification of coal from Huntly East Mine, New Zealand

Rock Mass Rating (RMR) measurements from 65 sites within Huntly East underground coal mine are presented. All measurements are in coal, for which the dominant discontinuities are vertical cleat. Basic RMR values using two discontinuity spacings are presented: overall RMR based on the average spacing of all individual discontinuities; and cleat zone RMR based on the average spacing between zones of cleat. Cleat orientations are highly variable, but on average approximately parallel horizontal stress axes (face cleat follows maximum horizontal stress axis, butt cleat follows minimum horizontal stress axis).Contours of RMR variations throughout the mine are used to compare rock mass conditions with geological structure. It is apparent that: (1) RMR is least within downthrown fault blocks, and particularly immediately on the downthrown sides of faults, and greatest in upthrown fault blocks; and (2) RMR contours parallel horizontal stress axes within fault-bounded blocks, and bend to parallel faults at block boundaries. From similar contours for parameters contributing to RMR, the Rock Quality Designation (RQD), groundwater rating, and discontinuity condition rating create most of the observed variations in RMR. RQD is determined from the measured discontinuity frequency and hence is a measure of the degree of fracturing of the rock mass. This is interpreted as influencing the groundwater and condition parameters directly by allowing greater water ingress. Discontinuity frequency is greatest (least spacing) in the immediate vicinity of faults, and in downthrown fault blocks, generating low RMR values. Within fault blocks RQD varies little, so RMR contours align with cleat orientations.As RMR contours, faults, stress field and cleat orientation are clearly interrelated, there is unequivocally a connection between RMR and structural geology; this allows some predictive capacity in terms of ground conditions. If geological features can be accurately defined through either drilling programs or seismic surveys, then ground conditions may be predicted before panels are driven.     

The Shape and Volume of the Skaergaard Intrusion, Greenland: Implications for Mass Balance and Bulk Composition

Re-examination of the Skaergaard intrusion in the context ofits regional setting, combined with new data from explorationdrilling, has resulted in a revised structural model for theintrusion. It is modelled as an irregular box, c. 11 km fromnorth to south, up to 8 km from east to west, and 3·4–4km from the lower to the upper contact. The walls of the intrusionare inferred to follow pre-existing and penecontemporaneoussteep faults, and the floor and roof seem largely controlledby bedding planes in the host sediments and lavas, similar toregional sills. The suggested shape and volume are in agreementwith published gravimetric modelling. Crystallization alongall margins of the intrusion concentrated the evolving meltin the upper, central part of the intrusion, best visualizedas an ‘onion-skin’ structure inside the box. Thetotal volume is estimated to c. 280 ± 23 km³, of which13·7% are referred to the Upper Border Series (UBS),16·4% to the Marginal Border Series (MBS) and 69·9%to the Layered Series (LS). In the LS, the Lower Zone (LZ) isestimated to constitute 66·8%, the Middle Zone (MZ) 13·5%and the Upper Zone (UZ) 19·7%. The new volume relationshipsprovide a mass balance estimate of the major and trace elementbulk composition of the intrusion. The parental magma to theSkaergaard intrusion is similar to high-Ti East Greenland tholeiiticplateau basalts with Mg number c. 0.45. The intrusion representsthe solidification of contemporary plateau basalt magma trappedand crystallized under closed-system conditions in a crustalreservoir at the developing East Greenland continental margin. KEY WORDS: bulk composition; emplacement; mass proportions; Skaergaard intrusion; structure     

Curve-Fitting Schemes for Fragmentation Data

Fragmentation measurements in the form of sieve passing and mass fraction data were used to test the capability of three different distributions to fit the observed data over a wide range in fragment size and mass. These distributions were based on Rosin-Rammler, lognormal and simple sigmoidal (S-shaped) functions, having 2 input parameters for the single-component versions and 5 input parameters for the two-component versions. Provided convergence was achieved in the non-linear curve-fitting technique, the two-component versions always provided superior fits to the observed data. However, these versions were very sensitive to variations in the values chosen for the input parameters. In this particular regard, the two-component sigmoidal function was the most robust. The present results also show that the two-component lognormal function provided the best fit to the fragmentation data in a general sense, and the two-component Rosin-Rammler function provided the worst fit. However, there was not a significant difference between any of the three methods.