考虑二期荷载的高填明洞加筋减载土压力计算

随着城市建设的迅速发展,既有高填明洞填土顶面将不可避免地出现新增结构物等二期荷载的情况。为了明确明洞回填完成后新增二期荷载对其顶部垂直土压力的影响,在已有明洞减载结构土压力计算公式的基础上,利用土体沉降弹性理论计算公式建立了土工格栅变形与土体沉降变形的关系,并考虑二期荷载作用,进一步完善了高填明洞减载前后的洞顶垂直土压力计算公式。建立数值分析模型,将数值分析结果与文中公式计算结果进行了对比。结果表明：公式计算与数值分析结果较为接近,表现出相同的规律性;有无减载措施对明洞回填土压力影响较大,填土越高,减载越显著,实际作用在明洞顶土压力越小。新增二期荷载作用下的明洞顶垂直土压力计算,应考虑其对土体沉降变形的影响,而非简单叠加。     

爆炸荷载作用下深埋圆形隧洞的饱和黏弹性土-衬砌系统动力响应

假定土骨架服从标准线性固体黏弹性本构关系,研究了深埋圆形隧洞的饱和黏弹性土-弹性衬砌耦合系统在轴对称爆炸作用下的瞬态动力响应。首先,基于饱和土的Biot模型和衬砌的弹性理论,通过引入势函数和Laplace变换,利用弹性衬砌和饱和黏弹性土界面处的连续性条件以及边界条件,得到饱和黏弹性土体和弹性衬砌位移、应力和孔隙水压力等在Laplace变换域中的解析解。其次,利用Laplace数值Crump逆变换得到耦合系统在时间域的动力响应,数值分析了不同土体模型下土体-衬砌耦合系统的径向位移和环向应力以及土体孔隙水压力等。结果表明：对不同土体模型的土体-衬砌耦合系统,其在爆炸载荷作用下的动力响应性态基本一致,但动力响应的振动周期和幅值等具有明显的差异。同时,对于饱和黏弹性土-弹性衬砌系统,土体黏性参数对土体径向位移和孔隙水压力有明显的影响,但对土体环向应力影响较小。     

不同平衡堆载条件下桩基承载特性的原位试验研究

沿海吹填围垦地区土质较差,淤泥软弱土层较厚,在后期填土作用下土体会产生很大的固结沉降。后期不同堆载填土方式对桥梁基础影响较大,可降低基桩承载力,同时平衡堆载主要增加基桩的沉降,而不平衡堆载则对基桩水平位移影响较大。结合台州湾大桥工程建设,选取3根基桩进行了平衡堆载（围载）试验,另外,选取了3根基桩进行了不平衡堆载试验,研究不同堆载条件下对桩基承载特性的影响。现场试验结果表明,平衡堆载条件下主要引起桩侧产生负摩阻力,堆载高度达到4 m,堆载面积为24 m×16 m时,负摩阻力总和达到2 687 kN左右,中性点深度约为29.5 m,约为0.36倍桩长,且负摩阻力的发展是随时间而变化的;不平衡堆载条件下主要产生土拱效应,使桩基产生较大的水平位移,试验中不平衡堆载对吹填区的影响主要在距离地面20 m范围之内,土中最大水平位移出现在距离地面4～5 m左右位置,而桩身最大水平位移出现在桩顶。     

济阳坳陷特低渗透油藏地质多因素综合定量分类评价

在定量表征特低渗透油藏开发效果及地质特征的基础上,探讨特低渗透油藏开发效果主控地质因素。应用灰色关联分析法对济阳坳陷特低渗透油藏开展地质多因素综合定量分类评价,形成了一套以开发效果表征特低渗透油藏综合特征、从单井到区块基于灰色关联分析的特低渗透油藏地质多因素综合定量分类评价方法。研究结果表明,济阳坳陷特低渗透油藏主要为滩坝砂、浊积岩、砂砾岩沉积,具有埋藏深度大、粒度细、分选较好、孔喉微细、单层厚度薄、分布零散、比储量丰度低、流动性差的地质特点。定义累积产油差表征开发效果以反映特低渗透油藏综合特征,其主控地质因素为油层厚度层数比、砂岩厚度层数比、平均粒径、采油段中深、渗透率、孔隙度、比储量丰度。通过地质多因素综合定量分类评价,将济阳坳陷特低渗透油藏分为3类：Ⅰ类综合评价分数大于0.6,累积产油差大于4 500,开发效果最好;Ⅱ类综合评价分数0.4~0.6,累积产油差-2 500到4 500,开发效果中等;Ⅲ类综合评价分数小于0.4,累积产油差小于-2 500,开发效果差。利用不同区块已有开发数据检验,分类评价结果与实际生产情况一致性良好。Ⅰ类、Ⅱ类特低渗透油藏应该作为现阶段特低渗透油藏直井、水平井优先开发的对象。     

准噶尔盆地南缘硫磺沟煤层气富集主控地质因素及有利区优选

为评价煤层气资源勘探开发潜力和指导矿井安全生产,对准噶尔盆地南缘硫磺沟煤矿主煤层(4-5、7、9-15号煤)的储层物性特征(显微组分、裂隙及含气性等)进行了测试分析,结合现场钻井资料、瓦斯解吸及瓦斯涌出量等资料,从构造、沉积、煤层埋深、水动力条件等方面分析了该区煤层气的控气地质因素。结果表明：煤储层物性较好,孔裂隙较为发育,微裂隙高达3 935条/9 cm²;煤层含气性(瓦斯含量)较好,4-5号煤层为4.88~10.81 m³/t,平均6.56 m³/t。控气地质因素分析表明,准南硫磺沟煤层气的控气模式以构造-水动力耦合控气为主。同时,利用多层次模糊数学综合评价模型,预测的硫磺沟煤矿(4-5号煤)煤层气赋存有利区为钻孔29-3和28-3周边区域。     

川东地区震旦系灯影组储层特征及其控制因素

采用宏观和微观相结合的 方法,通过扫描电镜、阴极发光等手段,分析川东地区震旦系灯影组钻井、岩心和露头剖面样品的镜下岩石学特征,研究川东地区震旦系灯影组白云岩储层的特征及控制因素。研究结果表明灯影组白云 岩储层主要发育在灯二段和灯四段,主要储集岩类型为微生物白云岩、颗粒白云岩和距两期风化壳0~200 m范围内的角砾白云岩和溶孔白云岩;储集空间以次生的孔、缝、洞为主,主要为粒间溶孔、粒内 溶孔、次生晶间孔、构造裂缝、溶洞等。沉积环境是影响灯二段储层发育的主要因素,其有利储集相带主要是位于水动力能量较强的或有利于造礁生物繁殖的高能颗粒滩和微生物云坪沉积环境;溶蚀作 用,特别是古岩溶作用是灯四段储层发育的主要因素。早期的桐湾运动形成了灯影组的大规模孔洞,而其后的构造运动则建立了研究区内特别复杂的孔隙－洞穴－裂缝系统。     

致密砂岩气藏可动流体赋存特征的微观地质因素: 以苏里格气田东部盒8段储层为例

以苏里格气田东部盒8段典型的致密砂岩气藏为例,运用核磁共振、恒速压汞、铸体薄片、物性、X-衍射等实验资料,探讨了影响可动流体赋存差异的微观地质 因素。结果表明,盒8段储层可动流体饱和度低,T₂谱分布均为左高峰右低峰的双峰态;黏土矿物的充填与孔隙类型是孔隙结构复杂的重要因素,孔隙结构是影响可动流体赋存特征的关键;面孔率、喉道 半径、孔喉半径比是影响可动流体饱和度的主要因素,有效孔隙体积、分选系数对可动流体饱和度影响明显,储层物性、黏土矿物、有效喉道体积、孔隙半径对可动流体饱和度影响较弱。     

电网磁暴灾害风险影响因素研究综述

磁暴是源自太阳磁场剧烈变化的地球空间效应,随着电网规模的增大和电压等级的增高,磁暴灾害已经成为诱发电网故障风险的威胁之一.研究电力系统磁暴灾害风险的影响因素可为预防与控制其引发的电网事故提供重要参考.在分析历史典型磁暴事件的基础上,剖析了磁暴诱发电力系统故障的机理,阐述了故障传播与电力系统响应的过程,总结了近年来关于影响电力系统的地磁感应电流水平及其产生的变压器无功损耗方面的研究成果,从磁暴本身的特点和电力系统的参数与结构两方面将影响因素分类.以GIC标准模型,通过改变磁暴扰动环境和电力系统参数,说明了各因素对电网磁暴灾害风险的影响程度,并比较了不同因素影响后果的差异,最后指出了尚未解决的问题和可能的研究方向.     

Nonlinear response estimates of RC frames using linear analysis of SDOF systems

An approximate‐simple method for nonlinear response estimates of reinforced concrete frames subjected to near‐field and far‐field records is presented in this paper. The approximate method is based on equivalent single‐degree‐of‐freedom and linear multi‐degree‐of‐freedom models. In this procedure, the nonlinear maximum roof displacement is estimated using an effective period factor and elastic response spectrum with an equivalent damping. The effective period factor was proposed for far‐field and near‐field ground motion records. For regions of high seismicity, the maximum roof displacement can be estimated by applying an effective period factor of 2.3 and 2.1 for near‐field and far‐field records, respectively, and 9% damped displacement response spectrum. For regions of moderate seismicity, a lower effective period factor of 1.9 and 1.8, for near‐field and far‐field records, respectively, can be applied to estimate the maximum roof displacement. A relationship between linear and nonlinear response of multi‐degree‐of‐freedom systems was also proposed to obtain estimates of the maximum inter‐story drift of nonlinear responding reinforced concrete frames. In addition, the effects of number of ground motion records used in the analyses on the scatters of results were investigated. The required number of ground motions to produce a reliable response was proposed. Copyright © 2013 John Wiley & Sons, Ltd.     

Design,simulation, and large‐scale testing of an innovative vibration mitigation device employing essentially nonlinear elastomeric springs

This study proposes an innovative passive vibration mitigation device employing essentially nonlinear elastomeric springs as its most critical component. Essential nonlinearity denotes the absence (or near absence) of a linear component in the stiffness characteristics of these elastomeric springs. These devices were implemented and tested on a large‐scale nine‐story model building structure. The main focus of these devices is to mitigate structural response under impulse‐like and seismic loading when the structure remains elastic. During the design process of the device, numerical simulations, optimizations, and parametric studies of the structure‐device system were performed to obtain stiffness parameters for the devices so that they can maximize the apparent damping of the fundamental mode of the structure. Pyramidal elastomeric springs were employed to physically realize the optimized essentially nonlinear spring components. Component‐level finite element analyses and experiments were conducted to design the nonlinear springs. Finally, shake table tests using impulse‐like and seismic excitation with different loading levels were performed to experimentally evaluate the performance of the device. Experimental results demonstrate that the properly designed devices can mitigate structural vibration responses, including floor acceleration, displacement, and column strain in an effective, rapid, and robust fashion. Comparison between numerical and experimental results verified the computational model of the nonlinear system and provided a comprehensive verification for the proposed device. Copyright © 2014 John Wiley & Sons, Ltd.