Geometry and kinematics of brittle deformation in the Central Cameroon Shear Zone (Kékem area): Implication for gold exploration within the Central Africa Fold Belt in Cameroon

The Central Africa Fold Belt (CAFB) is a collision belt endowed with gold deposits in Eastern Cameroon area mined for about 50 years. However, favorable areas for gold exploration are poorly known. This paper presents (1) the kinematics of the brittle deformation in the Kékem area in the SW portion of the Central Cameroon Shear Zone and (2) constraints gold mineralization events with respect to the collisional evolution of the CAFB. The authors interpret that the conjugate ENE to E and NNW to NW trending lineament corresponds to the synthetic (R) and the antithetic (R’) shears, which accompanied the dextral slip along the NE to ENE striking shear. The latter coincides with the last 570–552 Ma D₃ dextral simple shear-dominated transpression, which is parallel to the Bétaré Oya shear zone hosting gold deposits. Gold mineralizations, which mainly occurred during the last dextral shearing, are disseminated within quartz veins associated to Riedel’s previous structures reactivated due to late collisional activities of the CAFB as brittle deformation. Gold mineralizations occurred mainly during the 570–552 Ma D₃ event. The reactivation, which might be due to dextral simple shear during mylonitzation, plausibly remobilized the early gold deposits hosted in syn-compressional rocks and/or possibly focused deep-sourced fluid mixed with those released by dehydration. Therefore, the Central Cameroon Shear Zone where Kékem is located, and which shows similar petrographical and structural features to those controling Batouri gold district, is a target area for gold exploration in Cameroon.     

安口镇含金韧-脆性剪切带地质特征

柳河县安口镇一带太古宙地体中发育有一条北东向韧—脆性剪切带,该带由糜棱岩化英云闪长岩、绿泥糜棱片岩、绢云千糜岩等组成,原岩为深成变质的长英质片麻岩。带内已知有金矿(点)6处,其成因是深成变质含矿流体沿剪切带上侵而形成的,受韧性剪切带控制的中低温热液型金矿,因此,加强对韧性剪切带的特征及控矿机制的综合研究对本区的进一步找矿工作将起到事半功倍的效果。     

基于孔隙率的延安黄土抗剪强度模型

孔隙率对黄土抗剪强度具有非常重要的影响,然而,孔隙率对黄土抗剪强度影响效果的认识并不充分。本文以陕西省延安黄土为研究对象,开展不同孔隙率的黄土直剪试验研究,探讨了孔隙率对粘聚力与内摩擦角的定量变化关系;并以此为基础,构建了基于孔隙率的延安黄土抗剪强度模型,并对其进行了验证。研究结果表明:(1)延安黄土粘聚力与孔隙率间呈幂函数变化关系;(2)延安不同孔隙率黄土内摩擦角取值呈现出两个区间,当孔隙率n≥0.4时,其内摩擦角在25±2.5°的范围内变动,而当孔隙率n<0.4时,其内摩擦角在29.5±2°的范围内变动;(3)通过分析得到了基于孔隙率的延安黄土抗剪强度模型,且该模型得到的黄土抗剪强度理论值与实测值间的误差较小,相对误差均在7%以内,具有较高的精确度。研究成果不仅能为延安黄土抗剪强度研究等提供技术支持,而且还能为该地区的工程建设等方面提供理论参考。     

库岸边坡倾角及水位变化对红土型库岸稳定性影响研究

水库库岸失稳对水库安全运行有重大影响。采用土工试验和干湿循环试验,结合数值计算及理论分析,研究红土型库岸边坡倾角和库水位升降与库岸稳定性的关系。结果表明:(1)在一定初始干密度条件下,红土抗剪强度随水位升降循环次数增加而非线性减小,且在水位升降循环约10次时趋于稳定。(2)在一定水位升降速率、升降幅度和升降循环次数条件下,红土型库岸稳定安全系数随库岸边坡倾角的增加总体上呈减小的趋势,且在边坡倾角为50°左右存在稳定安全系数极小值。(3)在一定水位升降循环次数条件下,水位上升到坡高的60%左右为上升阶段的相对危险区域,且水位上升速率对库岸稳定安全系数影响很小;水位下降至坡高的70%左右为库水位下降阶段的相对危险区域,且水位下降速率越大,库岸稳定安全系数越小。(4)针对一定初始干密度,库岸稳定安全系数先随水位升降循环次数的增加而减小,但在水位升降循环次数约10次后逐渐趋于稳定。库岸岩土体性质及库岸边坡倾角、水位变化都会对库岸稳定产生影响。     

Current-induced scour beneath initially elevated subsea pipelines

When a subsea pipeline is laid on an uneven seabed, certain sections may have an initial elevation with respect to the far-field seabed, e_o, and thus potentially affecting the on-bottom stability of the pipeline. This paper focuses on quantifying the effects of the upstream dimensionless seabed shear stress, θ_∞, and Reynolds number, Re, on: (1) the maximum dimensionless seabed shear stress beneath the pipe, θ_max, to be compared to the critical shear stress in order to determine whether scour would occur and progress towards an equilibrium state; and, (2) the dimensionless equilibrium scour depth beneath the pipe, S_eq/D. Using a 2-D Reynolds averaged Navier-Stokes (RANS) approach along with the k-ω Shear Stress Transport (SST) turbulence model, a parametric study involving 243 computational fluid dynamics (CFD) simulations was conducted. The simulation results were used to develop a closed-form equation for the prediction of θ_max. Subsequently, experimental measurements of S_eq/D have been compiled from published literature, to develop a new closed-form equation for the prediction of S_eq/D with a high correlation to the experimental data. In summary, we present two closed-form equations for the prediction of θ_max and S_eq/D for pipelines with an initial e_o/D, which are applicable for both clear-water and live-bed conditions. The effects of θ_∞ and Re have been included, albeit Re having a small influence as compared to the other parameters.     

基于剪切波速的深层砂土地震液化研究

阐述了剪切波速法判别饱和砂土液化的原理,结合武汉地区某工程实例,对场地内埋深超越"规范法"适用范围的砂层进行液化判别,确定场地的临界液化深度。通过与室内动三轴试验的对比得出,2种方法的液化判别结果及确定的临界液化深度均吻合较好,验证了以剪切波速为指标的液化评估方法的可行性。     

海洋湍流观测技术

湍流在海洋能量和水体的交换演化中起着非常重要的作用。海洋湍流研究的发展和海洋湍流观测仪器的研发密切相关。世界上湍流观测仪器的研发起步于上世纪50年代,但是我国在湍流观测设备方面到目前为止仅仅处于起步和引进国外设备阶段。针对我国的情况,文中对海洋湍流观测的平台、探头测量原理及其数据修正、资料后处理等关键技术做一个总结性的介绍,为我国使用引进的海洋湍流设备和自主开发海洋湍流测量设备提供参考。     

Analysis of threshold and incipient conditions for sediment movement

Prediction of threshold conditions and incipient motion is the essential issue for the study of sediment transport. This work compares existing empirical threshold curves proposed for Shields diagram, a method based on the concept of probability of sediment movement, and an empirical method based on movability number. These methods are used to predict the incipient motion conditions for experimental runs taken from various studies. Most of the experimental data, used in this work, have not been used before in derivation of alternative formulations for Shields diagram and other methods. The empirical threshold curves based on the Shields entrainment function was the least successful at predicting the measured incipient motion conditions, while the use of the movability number gives good predictions of critical shear velocity compared with experimental data.     

A traversing system to measure bottom boundary layer hydraulic properties

This study describes a new convenient and robust system developed to measure benthic boundary layer properties, with emphasis placed on the determination of bed shear stress and roughness height distribution within estuarine systems by using velocity measurements. This system consisted of a remotely operated motorised traverser that allowed a single ADV to collect data between 0 and 1 m above the bed. As a case study, we applied the proposed traversing system to investigate bottom boundary layer (BBL) hydraulic properties within Coombabah Creek, Queensland, Australia. Four commonly-employed techniques: (1) Log-Profile (LP); (2) Reynolds stress (RS); (3) Turbulent Kinetic Energy (TKE); and (4) Inertial Dissipation (ID) used to estimate bed shear stresses from velocity measurements were compared. Bed shear stresses estimated with these four methods agreed reasonably well; of these, the LP method was found to be most useful and reliable. Additionally, the LP method permits the calculation of roughness height, which the other three methods do not. An average value of bed shear stress of 0.46 N/m², roughness height of 4.3 mm, and drag coefficient of 0.0054 were observed within Coombabah Creek. Results are consistent with that reported for several other silty bed estuaries.     

Estimation of the wave-related ripple characteristics and induced bed shear stress

A large data set on ripples was collected and examined. A set of new formulas for the prediction of the ripple characteristics is proposed with an emphasis on the disappearance of the ripples. The ripple wavelength was observed to be proportional to the bottom wave excursion but also to be a function of the grain-related Shields parameter and wave period parameter introduced by Mogridge et al. (1994). The ripple steepness was found to be nearly constant for orbital ripples, and with a sharp decrease for suborbital ripples. Two empirical functions are added including the effects of the critical Shields parameters (inception of transport and inception of sheet flow), i.e. giving the boundaries for the ripple existence's domain. The proposed formulas yield better prediction capabilities compared to the previously published formulas, especially when ripples are washed out. The effect of the ripple characteristics on the roughness height and the calculation of the bed shear stress is also discussed. It appeared that the bed shear stress calculation is more sensitive to the empirical coefficient a_r introduced in the estimation of the ripple-induced roughness height or to the limits of existence of the ripples than the ripple characteristics themselves.