潜孔锤偏心跟管钻进法在卵砾石地层岩土工程勘察中的应用

卵砾石地层是钻探工程中常见的一种典型的难钻进不稳定地层。通过采用潜孔锤偏心跟管钻进法,从根本上解决了卵砾石地层难以钻进的难题,结合都匀市区岩土工程勘察实例,笔者认为潜孔锤偏心跟管钻进法是在卵砾石地层钻进中行之有效的一种钻进法。     

An inexpensive and portable drill rig for bedrock groundwater studies in headwater catchments

Bedrock groundwater dynamics in headwater catchments are poorly understood and poorly characterized. Here, we present an inexpensive and portable bedrock drilling system designed for use in remote locations. Our system is capable of drilling bedrock wells up to 11 m deep and 38 mm in diameter in a wide range of bedrock types. The drill consists of a lawn mower engine adapted to rotate a diamond tipped coring bit, a small water pump to cool and flush the drill bit and a scaffolding platform for stable footing on steep slopes. The complete drilling assembly costs under $ 2000 USD. Here, we show proof‐of‐concept of our approach with 40 successful wells drilled in different geological substrates, including a conglomerate at the Maimai experimental catchment in New Zealand, volcanic breccias at the HJ Andrews experimental watershed in Oregon, USA, sandstone and siltstone at the Alsea watershed in Oregon, USA, and basalt at the Los Gavilanes experimental watershed in Veracruz, Mexico. We also present a transparent comparison between our design and other portable bedrock drilling systems and outline the strengths and weaknesses of each system. Copyright © 2011 John Wiley & Sons, Ltd.     

以PC1井三维荧光光谱分析结果论油气垂向运移

本文以Pcl并不同深度岩心和地表土壤作为分析样品，通过三维全扫描荧光光谱等分析。揭示了该区油气垂向运移规律和地下油气的某些分布特征。研究表明，芳烃三维荧光光谱方法是研究芳烃组成变化最理想的手段之一，可以有效地解决油气运移等问题。     

气举反循环钻深度的理论计算与加深试验

运用气举反循环钻进、在满足一定条件下适当增加双壁钻具长度即可得到较大钻进孔深，本文通过理论计算及实验，证实了使用现有设备，气举气循环可以更好的满足超午米深水井的施工要求。     

煤矿采空区钻孔注浆治理工艺

钻孔注浆充填固结处理煤矿采空区塌陷是一种经济快捷的有效方法，本文就其施工工艺方法进行了简单分析，期望能为其它类似工程提供参考。     

滚刀钻头在桩基施工中的应用

焊齿破岩滚刀钻头适应多种地层钻进。本文主要介绍了焊齿破岩滚刀钻头的钻进工作原理，在桩基施工中的钻进技术参数，滚刀刀齿的修复及应用效果。     

Quaternary vertical offset and average slip rate of the Nojima Fault on Awaji Island, Japan

Abstract Drilling was carried out to penetrate the Nojima Fault where the surface rupture occurred associated with the 1995 Hyogo-ken Nanbu earthquake. Two 500 m boreholes were successfully drilled through the fault zone at a depth of 389.4 m. The drilling data show that the relative uplift of the south-east side of the Nojima Fault (south-west segment) was approximately 230 m. The Nojima branch fault, which branches from the Nojima Fault, is inferred to extend to the Asano Fault. From the structural contour map of basal unconformity of the Kobe Group, the vertical component of displacement of the Nojima branch–Asano Fault is estimated to be 260–310 m. Because the vertical component of displacement on the Nojima Fault of the north-east segment is a total of those of the Nojima Fault of the south-west segment and of the Nojima branch–Asano Fault, it is estimated to total to 490–540 m. From this, the average vertical component of the slip rate on the Nojima Fault is estimated to be 0.4–0.45 m/10³ years for the past 1.2 million years.     

偏重钻铤在丁集矿冻结造孔施工中的应用

钻井技术的关键是预防及控制孔斜,通过对目前常用4种防斜钻具组合的适岩性、井深、井斜及钻效等指标对比,在冻结造孔施工中选用了适用地层广、防斜性能好并具有纠斜作用的偏重钻铤。为发挥偏重钻铤的防斜作用,宜增大转速,并使钻铤减去部分的重量应位于离轴线尽可能远的部位。在淮南丁集冻结孔施工的三十多口钻孔中,井斜一般均在0．5°以内,钻效超过2400m/台·月。     

依兰矿区钻探施工泥浆选型的研究

依兰矿区第三系上部的砂泥岩段,因泥岩的水敏水化作用及粗砂岩易坍塌等原因造成,区内钻孔孔壁极不稳定,经常发生粘卡钻具事故。为抑制泥岩的水敏水化,阻止泥岩水化和井壁岩石剥落,增强其防塌能力,在选择腐植酸钾做主剂的基础上选择CMC作降失水增粘剂,选择分子量为300万～500万、水解度30%的聚丙烯酰胺(PAM)作絮凝剂,以加速岩屑沉降,控制固相侵入,降低失水。在钻遇半胶结泥岩时,为防止缩径、坍塌,采用在泥浆中加入重晶石粉,把泥浆比重调整到1.15～1.20g/cm~3,利用泥浆液柱压力控制泥岩缩径和孔壁坍塌。通过实验及现场应用,为该区选择的KHM-CMC-PAM高聚物泥浆配方,能有效地防止水敏性易塌地层的粘卡钻事故,具有护壁防塌、提高钻效等技术效果。