非等截面桩超声波成孔质量检测

分析了非等截面超声波成孔质量检测的几个主要影响因素,给出了相应得改进措施。用工程实例说明超声波反射技术是一种保证非等截面桩成孔质量和成桩质量必不可少的检测方法。     

襄樊汉江四桥大口径灌注桩成孔施工实践

介绍了使用泥浆护壁气举反循环回转钻进工艺进行襄樊汉江四桥大口径嵌岩桩的施工实践。施工中采用下置双护简隔离卵石层，合理选用钻头类型(卵砾石层采用五翼合金刮刀钻头，基岩采用球齿滚刀钻头)和钻进参数(混合器沉没深度，尾管长度，孔内空气流量与压力)，摸索与总结出一套复杂地层成孔施工经验。     

煤田勘查超千米深孔快速钻进技术探讨

针对目前国内煤田勘查主要机具及工艺技术方法存在的主要问题,结合煤田勘查地层地质条件和超千米深孔施工要求,研制了液压立轴式HTJ-2000型钻机和新型绳索取心钻具,并就配套设备选型、钻进工艺、钻进参数、泥浆指标及应用效果进行了阐述.该项技术的应用,已明显提高了钻效,使钻孔深度达到1 350m.     

地下圆形衬砌隧道对沿线地震动的影响(II):数值结果

利用地下圆形衬砌隧道对入射平面P波和SV波散射级数解答，定量分析了入射波长、入射角度、隧道直径、衬砌刚度等因素对沿线地表位移放大作用的影响。计算结果表明，当入射频率较低时，地下隧道的存在对地表位移幅值影响不大；而当入射频率较高时，地表位移幅值可以达到无隧道情况的4．5倍以上；衬砌情况下地表位移幅值可以高出非衬砌情况的87．8％。建议在地铁的规划设计中考虑地下隧道的建设对隧道沿线设计地震动的影响。     

地下导线随盾构推进逐段接测中的可靠性检验

盾构法施工的要点是需要在井下布设高精度的控制支导线，当我们根据盾构推进进度对导线接测时，由于观测条件、观测方法、观测仪器基本相同，但观测、的成果往往会存在一定的差异，有时我们无法直接判断成果的正确与否，此时，采用测量平差中的统计检验的方法来分析这些观测数据，可以取得比较满意的结果。     

可控深度电法对水平柱体和垂直界面的计算和实验

球状地球体可控深度电法的效应系数可近似地全面表达可控深度电法和各种效应。通过点源二度体的电算模拟实验，证明了该方法在水平柱状体和地下存在电阻率垂直界面的条件下，也是有效的。     

DGSC—203型液动射流冲击器在地热井的试验

介绍了新研制的DGSC－203石油钻井液动射液冲击器的性能参数及结构设计上的创新点，测试所获得的排量与压降之间的关系曲线可指导冲击器的使用。生产性试验证明该冲击器工作稳定，可大幅度提高硬地层钻井效率，克服钻柱振动，延长钻柱的使用寿命，具有良好应用前景。     

Study of a semi‐active stiffness damper under various earthquake inputs

Semi‐active stiffness damper (SASD) is one of many semi‐active control systems with the capability to mitigate the dynamic response using only a small amount of external power. The system consists of a hydraulic damper connected to the bracing frame in a selected story unit. In this paper, study of a SASD in two building models of five‐stories under four benchmark earthquake records is reported. The purpose of this study is to evaluate the effectiveness of the control system against structure type and varying earthquake inputs. Various control laws are chosen to work with SASD, such as: resetting control, switching control, linear quadratic regulator (LQR) and modified LQR, and the results are compared with no control and passive control cases. Numerical results show that the use of a SASD is effective in reducing seismic responses. Control effectiveness is dependent on the type of structure and earthquake excitation. Passive control is less effective than other control cases as expected. Resetting control, switching control and LQR generally perform similarly in response reduction. While modified LQR is more efficient and robust compared with other control algorithms. Copyright © 2002 John Wiley & Sons, Ltd.     

Ground‐shaking mapping for a scenario earthquake considering effects of geological conditions: a case study for the 1995 Hyogo‐ken Nanbu,Japan earthquake

In order to examine the applicability of ground‐shaking mapping techniques to a near‐field earthquake, a peak ground velocity map of the 1995 Hyogo‐ken Nanbu, Japan earthquake computed from seismic zoning methods that consider the effects of geological conditions is compared with the actual observed intensity map. When computing the ground‐shaking map, the site amplification at each site is calculated in terms of the average shear‐wave velocity of the ground estimated from the corresponding geomorphological conditions. This map shows a relatively good agreement with the observed intensity map. However, the computations provide smaller values for certain disastrous areas of the earthquake, where the effects on ground motion of a deep, irregular underground structure have been reported. The effect of such structures on site response is examined implementing 2D FEM analyses, thereby being also incorporated into the method. Results considering the effect of the irregular underground structure show better agreement with the observed intensity map. Copyright © 2002 John Wiley & Sons, Ltd.     

离散裂隙渗流方法与裂隙化渗透介质建模

流体渗流模拟的连续介质方法通常适用于多孔地质体，并不一定适用于裂隙岩体，由于裂隙分布及其特征与孔隙差异较大。若流体渗流主要受裂隙的控制，对于一定尺寸的裂隙岩体，多孔介质假设则较难刻划裂隙岩体的渗流特征。离散裂隙渗流方法不但可直接用于模拟裂隙岩体非均质性和各向异性等渗流特征，而且可用其确定所研究的裂隙岩体典型单元体及其水力传导（渗透）张量大小。主要讨论了以下问题：（1）饱和裂隙介质中一般的离散流体渗流模拟；（2）裂隙岩体中的REV（典型单元体）及其水力传导（渗透）张量的确定；（3）利用离散裂隙网络流体渗流模型研究裂隙方向几何参数对水力传导系数和REV的影响；（4）在二维和三维离散裂隙流体渗流模型中对区域大裂隙和局部小裂隙的处理方法。调查结果显示离散裂隙流体渗流数学模型可用来评价不同尺度上的裂隙岩体的水力特征，以及裂隙方向对裂隙化岩体的水力特征有着不可忽视的影响。同时，局部小裂隙、区域大裂隙应当区别对待，以便据其所起的作用及水力特征，建立裂隙化岩体相应的流体渗流模型。