饱和软土大应变自重固结非线性分析

饱和软土的自重固结涉及许多复杂的非线性问题,而现有分析方法一般基于线性假设,将固结控制方程简化,在沉降变形较大的情况下并不合理。基于Gibson大变形固结方程,推导在单面排水和双面排水条件下的边界条件,综合考虑饱和软土的自重特性与非线性压缩、渗透关系,采用稳定性较好的Crank-Nicolson型差分格式离散并求解非线性控制方程,并从孔隙比、沉降、孔隙水流速3个方面将数值解与CS2固结数值模型进行对比验证。结合工程实例,研究土层不同初始厚度和初始孔隙比对自重固结的影响。结果表明：初始厚度与初始孔隙比较大土层最终沉降也较大。与传统方法相比,该方法所得出的数值解精度较高,实现了高度非线性固结方程的快速求解,其成果更能广泛运用于实际工程的分析之中。     

基于广义热力学的超固结土本构模型

基于广义热力学基本理论,通过考虑塑性剪切变形产生的能量一部分以塑性自由能的形式储存,并且该部分自由能与超固结度相关,结合修正剑桥模型的热力学函数形式建立了适用于超固结土的自由能函数和耗散函数。该耗散函数与当前应力状态无关,相关联流动法则仍然适用。由建立的耗散函数和自由能函数,推导了弹塑性本构关系的屈服函数、流动法则、硬化定律。通过4种不同超固结土的试验结果和计算结果进行比较,验证了模型的合理性。     

下穿隧道开挖引起的挤土桩沉降控制分析方法

随着地下空间开发利用的立体式发展,地下近接工程中结构相互作用问题日益突显。针对盾构隧道下穿既有挤土桩问题,提出了基于岩土介质小孔扩张（收缩）理论的分析方法。通过基于统一砂黏土本构模型和大应变假设推导的小孔扩张-收缩排水解析解,建立了隧-桩相互作用力学模型;提出了隧道开挖影响下桩基的承载力衰减因子,并采用荷载-沉降曲线预测了桩基沉降。由分析结果可知,隧道地层损失引起的桩侧承载力减小、桩端承载力减小和桩端刚度损失,三者共同作用促使桩基发生沉降失稳,并提出了桩基的承载力控制准则、稳定控制准则和变形控制准则。此外,研究得到了桩基失稳时隧道地层损失与各因素之间的相关关系。其结果为揭示隧道与邻近结构相互作用机制、保障地下结构稳定性提供了有效的分析手段和必要的理论依据。     

石英显微变形机制及流变学特征研究进展

石英是组成地壳的主要矿物之一,其物理性质与地壳的变形行为及流变学属性密切相关,因此石英的显微变形机制及流变学特征研究意义重大。随着石英显微变形机制及流变学属性实验学研究的深入,我们对石英在地壳变形过程中重要作用的认识也随之提升。本文从石英结构入手,对升温过程中石英主滑移系的转换进行了总结,并且升温过程中显微变形机制也发生了改变,对流变学内涵也不同,所以分述了石英的主要变形机制,及其流变学参数;由于应变局部化为地壳变形的研究热点,并且石英对应变局部化具有一定的指示意义,所以本文对石英在应变局部化过程中的表现进行了深入讨论。考虑到地壳变形的研究过程中,石英不常作为单矿物发生变形,所以本文对多相矿物的变形表现也进行了讨论。最后我们将简单介绍一些现今主流的石英显微变形机制的研究手段。     

混凝土徐变对抗滑桩结构的影响分析

混凝土徐变作用能够增大桩身弯曲变形,占用设计冗余。增大受拉侧混凝土裂缝宽度,降低结构耐久性。由于抗滑桩嵌固段属于隐蔽工程,无法及时发现此类问题,故将会对防治工程造成安全隐患。本文采用在抗滑桩埋设应变计,定期监测桩身应变数值的方法,研究了悬臂式抗滑桩在成桩后至一定时期内的实际受力变形情况。特别是对工程运行初期混凝土徐变作用下的桩身变形情况,进行了分析与总结,最后提出了抗滑桩设计时注意事项。     

The recognition of former melt flux through high‐strain zones

High‐strain zones are potential pathways of melt migration through the crust. However, the identification of melt‐present high‐strain deformation is commonly limited to cases where the interpreted volume of melt “frozen” within the high‐strain zone is high (>10%). In this contribution, we examine high‐strain zones in the Pembroke Granulite, an otherwise low‐strain outcrop of volcanic arc lower crust exposed in Fiordland, New Zealand. These high‐strain zones display compositional layering, flaser‐shaped mineral grains, and closely spaced foliation planes indicative of high‐strain deformation. Asymmetric leucosome surrounding peritectic garnet grains suggest deformation was synchronous with minor amounts of in situ partial melting. High‐strain zones lack typical mylonite microstructures and instead display typical equilibrium microstructures, such as straight grain boundaries, 120° triple junctions, and subhedral grain shapes. We identify five key microstructures indicative of the former presence of melt within the high‐strain zones: (a) small dihedral angles of interstitial phases; (b) elongate interstitial grains; (c) small aggregates of quartz grains with xenomorphic plagioclase grains connected in three dimensions; (d) fine‐grained, K‐feldspar bearing, multiphase aggregates with or without augite rims; and (e) mm‐ to cm‐scale felsic dykelets. Preservation of key microstructures indicates that deformation ceased as conditions crossed the solidus, breaking the positive feedback loop between deformation and the presence of melt. We propose that microstructures indicative of the former presence of melt, such as the five identified above, may be used as a tool for recognising rocks formed during melt‐present high‐strain deformation where low (<5%) volumes of leucosome are “frozen” within the high‐strain zone.     

Equivalent continuum strain calculations based on 3D particle kinematic measurements of sand

Constitutive modeling of granular materials has been a subject of extensive research for many years. While the calculation of the Cauchy stress tensor using the discrete element method has been well established in the literature, the formulation and interpretation of the strain tensor are not as well documented. According to Bagi, 1 researchers mostly adopt well‐known continuum or discrete microstructural approaches to calculate strains within granular materials. However, neither of the 2 approaches can fully capture the behavior of granular materials. They are considered complementary to each other where each has its own strengths and limitations in solving granular‐mechanics problems. Zhang and Regueiro 2 proposed an equivalent continuum approach to calculating finite strain measures at the local level in granular materials subjected to large deformations. They used three‐dimensional discrete element method results to compare the proposed strains measures. This paper presents an experimental application of the Zhang and Regueiro 2 approach using three‐dimensional synchrotron microcomputed tomography images of a sheared Ottawa sand specimen. Invariant Eulerian finite strain measures were calculated for representative element volumes within the specimen. The spatial maps of Eulerian octahedral shear and volumetric strain were used to identify zones of intense shearing within the specimen and compared well with maps of incremental particle translation and rotation for the same specimen. The local Eulerian volumetric strain was compared to the global volumetric strains, which also can be considered as an averaging of all local Eulerian volumetric strains.     

Modelling the time‐dependent behaviour of granular material with hypoplasticity

This paper presents a constitutive model for time‐dependent behaviour of granular material. The model consists of 2 parts representing the inviscid and viscous behaviour of granular materials. The inviscid part is a rate‐independent hypoplastic constitutive model. The viscous part is represented by a rheological model, which contains a high‐order term denoting the strain acceleration. The proposed model is validated by simulating some element tests on granular soils. Our model is able to model not only the non‐isotach behaviour but also the 3 creep stages, namely, primary, secondary, and tertiary creep, in a unified way.     

对欧拉矢量附加不等式约束的RELSM模型及其应用

借鉴选权拟合思想,对区域地壳运动的整体旋转和线性应变模型中欧拉矢量部分附加不等式约束,将区域地壳运动的欧拉参数约束到由多年观测资料确定的平均欧拉参数值附近,建立附有不等式约束的整体旋转和线性应变模型。对中国大陆构造环境监测网络在环渤海区域的近几期GPS观测速度场数据进行拟合分析,结果表明,本文方法通过不等式约束可适当增强块体整体运动趋势的平滑性,获得对速度场更高的拟合精度,可进一步增强模型的物理解释能力。